Psion Teklogix MLP 3040 Series manual Belt Loop System, Getting Started

Page 14

Getting Started

Belt Loop System

The belt loop system consists of two parts – a knob located on the bottom of the printer and a belt loop strap with a click on connector

To use the belt loop system, slide your belt through the strap of the belt loop and then insert the knob located on the bottom of the printer into the slot of the belt loop connector. Pull down on the printer until you hear a click. The printer is now secure and can safely hang down beside your hip.

To release the printer, press in on the two latches on the sides of the connector and pull the printer and knob up and clear of the slot.

Note: Do not force or pull the printer from the connector without pressing in on the two latches.

Image 14

Contents Psion Teklogix Corporation 3000 Kustom Drive Hebron, KY MLP3040 Series Operator’s ManualBattery Disposal FCC Part 15 Class BNehmen Sie den Drucker nicht in der Nähe einer Wärmequelle in Betrieb Do not operate near a heat sourceLesen Sie vor der Inbetriebnahme die Aufbau- und Bedienungsanleitung Page Introduction Printer ConfigurationPower Considerations Getting StartedAdvanced Setup Features Table of ContentsMaintenance and Troubleshooting SpecificationsIntroduction Page Getting Started Battery Installation and ChargingFigure 1 - Battery Installation and Power Connector Getting Started Installing MediaRoll Media Figure 2 - Opening Paper DoorFigure 4 - Paper Laying Through Print Head Cassette MediaFigure 3 - Media Support Movable SupportFigure 5 - Cassette In Printer Turning the Printer On and OffPerforming A Printer Self Test Interface Host Interface Set UpFactory Default Interface Settings Belt Loop System Control Panel Daily OperationIntroduction Figure 6 - Control PanelMLP 3040 and MLP 3040 LP Models Printer ConfigurationRemoving Printed Output MLP 3040 SL Models Battery ChargingPrinter Configuration Figure 7 - Tearing Off Printed Output Figure 9 - Using The Magnetic Card Reader Using the Magnetic Card ReaderFigure 8 - MLP 3040 Power Connector & Battery Indicator Power Connector Battery IndicatorPaper Door Open Additional MessagesCheck Paper Setup Basics Printer ConfigurationIntroduction To Setup Figure 10 - MLP 3040 Control PanelSelecting Menus Entering SetupExiting Setup Interface Menu Setup Menu SummaryFormat Menu Options MenuFormat Name Format MenuCurrent Format Left Margin FontSpacing Maximum Paper Speed Right MarginPrint Contrast Form Feed DistanceGap Sensitivity Mark SensingMark Sensitivity Tear to Mark DistancePresent Distance Interface MenuSerial Interface Current Host I/OData Bits EmulationBaud Rate Stop BitsETX/ACK Handshaking IrDA InterfaceXON/XOFF Handshaking RTS/CTS HandshakingBluetooth Interface Pairing ModeDiscoverability Role PolicyRole Policy Defer Discoverability OnAddress Wi-Fi InterfaceLocal Name WLAN SSID WLAN TypeWLAN Channel WLAN WEP BitsIP Address Assign WEP Key WEP Key WEP Key WEP KeyWLAN Auth IP AddressIP Gateway Options MenuIP Subnet Mask Tunnel Port NumberUser Language Auto Power DownMaximum Format Number Truncate LinesPrint Promotion Print Promo NoPage Pin # Interfacing To A Host ComputerRS-232C Serial Interface DescriptionIrDA Interface Bluetooth InterfaceFigure 12 - Wireless Indicator & IrDA Window Interfacing to a Host ComputerWi-Fi Interface Page Operation Without A Battery Power ConsiderationsAuto Power Down Standby OperationPage Figure 13 - Printer Cleaning Areas Maintenance and TroubleshootingCleaning Additional Battery and Safety Information Battery CareCharging the Battery Maintenance and TroubleshootingTesting the Power Supply and Battery Solution TroubleshootingError Messages MessageSolution Other ProblemsProblem Possible CauseObtaining Service Interface Menu Advanced Setup FeaturesFormat Menu Options MenuPage Print & Font Samples Print SamplesPrint & Font Samples Courier Font With International Extended Character SetCourier Font PC Line Drawing Extended Character Set Sans Serif Font Page Printing Specifications SpecificationsPrinter Specifications Power ManagementEnvironmental Specifications SpecificationsPhysical Specifications Operator Controls and IndicatorsLabels Media SpecificationsReceipt Paper Figure 14 - Black Mark Position Gap Sensing SpecificationsBlack Mark Position Supplies Supplies and AccessoriesAccessories Page Glossary of Terms Glossary