Psion Teklogix MLP 3040 Series manual WLAN Type, WLAN Channel, Wlan Ssid, WLAN WEP Bits

Page 33
WLAN Type

Printer Configuration

Note: After pressing the WLAN Channel Enter Button to move from Emulation to WLAN Type, the printer will pause and display “Waiting for Wi-Fi” while reading the current configuration from the Bluetooth interface module.

WLAN Type

Possible Values: Infrastructure*, Peer-to-Peer

WLAN Type Infrastructure

This feature specifies the type of wireless network the printer will be attached to. An Infrastructure network consists of nodes that connect to each other and/or a wired network through an Access Point. A Peer-to-Peer, or Ad-Hoc, network consists of nodes that connect directly to each other without the control of an access point.

WLAN Channel

Possible Values: 1* … 14

WLAN Channel 1

Note that this feature is only available if the WLAN Type is set to Peer-to-Peer.

This feature sets the radio channel to be used when communicating in a Peer-to-Peer network. When in an Infrastructure network, the radio channel is automatically assigned by the interface and Access Point.

WLAN SSID

WLAN SSID

 

any

Possible Values: any*,

Up to 16 characters of “0” through “9”, “A” through “Z”, “a” through “z”,

This feature specifies the “name” of the network the printer will connect to. This allows communications to be controlled, or routed to the appropriate nodes when multiple wireless networks are present. When set to “any”, the printer may connect to any available network(s).

To advance through the character positions, press the WLAN SSID Advance Button. To change the character at the current position, press the WLAN WEP Bits Increment Button. The order of characters that may be selected is “0123456789 ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz”.

WLAN WEP Bits

Possible Values: 0*, 64, 128

WLAN WEP Bits 0

This feature specifies the level of Wired Equivalent Security to use. If set to “0”, security is turned off. If set to a“64” or “128” bit encryption level, a WEP Key must be entered that matches the key on the other nodes on the network.

27

Page 32 Page 34
Image 33
Page 32 Page 34
Contents MLP3040 Series Operator’s Manual Psion Teklogix Corporation 3000 Kustom Drive Hebron, KYFCC Part 15 Class B Battery DisposalDo not operate near a heat source Lesen Sie vor der Inbetriebnahme die Aufbau- und BedienungsanleitungNehmen Sie den Drucker nicht in der Nähe einer Wärmequelle in Betrieb Page Power Considerations Printer ConfigurationIntroduction Getting StartedMaintenance and Troubleshooting Table of ContentsAdvanced Setup Features SpecificationsIntroduction Page Battery Installation and Charging Figure 1 - Battery Installation and Power ConnectorGetting Started Roll Media Installing MediaGetting Started Figure 2 - Opening Paper DoorFigure 3 - Media Support Cassette MediaFigure 4 - Paper Laying Through Print Head Movable SupportTurning the Printer On and Off Performing A Printer Self TestFigure 5 - Cassette In Printer Host Interface Set Up Factory Default Interface SettingsInterface Belt Loop System Introduction Daily OperationControl Panel Figure 6 - Control PanelPrinter Configuration Removing Printed OutputMLP 3040 and MLP 3040 LP Models Battery Charging Printer Configuration Figure 7 - Tearing Off Printed OutputMLP 3040 SL Models Figure 8 - MLP 3040 Power Connector & Battery Indicator Using the Magnetic Card ReaderFigure 9 - Using The Magnetic Card Reader Power Connector Battery IndicatorAdditional Messages Check PaperPaper Door Open Introduction To Setup Printer ConfigurationSetup Basics Figure 10 - MLP 3040 Control PanelEntering Setup Exiting SetupSelecting Menus Format Menu Setup Menu SummaryInterface Menu Options MenuFormat Menu Current FormatFormat Name Font SpacingLeft Margin Print Contrast Right MarginMaximum Paper Speed Form Feed DistanceMark Sensitivity Mark SensingGap Sensitivity Tear to Mark DistanceSerial Interface Interface MenuPresent Distance Current Host I/OBaud Rate EmulationData Bits Stop BitsXON/XOFF Handshaking IrDA InterfaceETX/ACK Handshaking RTS/CTS HandshakingPairing Mode Bluetooth InterfaceRole Policy Defer Role PolicyDiscoverability Discoverability OnWi-Fi Interface Local NameAddress WLAN Channel WLAN TypeWLAN SSID WLAN WEP BitsWLAN Auth WEP Key WEP Key WEP Key WEP KeyIP Address Assign IP AddressIP Subnet Mask Options MenuIP Gateway Tunnel Port NumberMaximum Format Number Auto Power DownUser Language Truncate LinesPrint Promo No Print PromotionPage RS-232C Serial Interface Interfacing To A Host ComputerPin # DescriptionFigure 12 - Wireless Indicator & IrDA Window Bluetooth InterfaceIrDA Interface Interfacing to a Host ComputerWi-Fi Interface Page Auto Power Down Power ConsiderationsOperation Without A Battery Standby OperationPage Maintenance and Troubleshooting CleaningFigure 13 - Printer Cleaning Areas Charging the Battery Battery CareAdditional Battery and Safety Information Maintenance and TroubleshootingTesting the Power Supply and Battery Error Messages TroubleshootingSolution MessageProblem Other ProblemsSolution Possible CauseObtaining Service Format Menu Advanced Setup FeaturesInterface Menu Options MenuPage Print Samples Print & Font SamplesCourier Font With International Extended Character Set Courier Font PC Line Drawing Extended Character SetPrint & Font Samples Sans Serif Font Page Printer Specifications SpecificationsPrinting Specifications Power ManagementPhysical Specifications SpecificationsEnvironmental Specifications Operator Controls and IndicatorsMedia Specifications Receipt PaperLabels Gap Sensing Specifications Black Mark PositionFigure 14 - Black Mark Position Supplies and Accessories AccessoriesSupplies Page Glossary of Terms Glossary
Top Page Image Contents