Schneider Electric TSXCUSBMBP user manual Safety Information, Important Information

Page 5

Safety Information

§

Important Information

NOTICE

Read these instructions carefully, and look at the equipment to become familiar with the

 

device before trying to install, operate, or maintain it. The following special messages

 

may appear throughout this documentation or on the equipment to warn of potential

 

hazards or to call attention to information that clarifies or simplifies a procedure.

 

The addition of this symbol to a Danger or Warning safety label indicates

 

that an electrical hazard exists, which will result in personal injury if the

 

instructions are not followed.

 

This is the safety alert symbol. It is used to alert you to potential personal

 

injury hazards. Obey all safety messages that follow this symbol to avoid

 

possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death, serious injury, or equipment damage.

WARNING

WARNING indicates a potentially hazardous situation, which, if not avoided, can result in death, serious injury, or equipment damage.

CAUTION

CAUTION indicates a potentially hazardous situation, which, if not avoided, can result in injury or equipment damage.

35011984 02/2006

5

Image 5 Contents
Tsxcusbmbp Page Table of Contents Using the Tsxcusbmbp with an Application Connecting to a Modbus Plus NetworkModbus Plus Network Diagnostic Functions Appendix a Tsxcusbmbp Settings for UnityImportant Information Safety InformationSchneider Electric. All Rights Reserved At a Glance About the BookAbout the Book Abbreviation/Acronym Expansion Glossary of Abbreviations AcronymsIntroduction Glossary Abbreviations Acronyms Abbreviations & Acronyms Topic OverviewSubject of this chapter Whats in this Chapter? Introduction Modbus Plus Communication for ApplicationsVirtual Serial Port VSPDescription Modbus Plus Network DiagnosticsTsxcusbmbp Hardware Overview Chapter? InstallationSubject of this Upgrading From Previous Version Installation RequirementsIntroduction How to install Tsxcusbmbp Driver? Installing the Tsxcusbmbp Driver SoftwareInstalling the Tsxcusbmbp Hardware How to install Tsxcusbmbp Hardware Status Establishing a Connection toDriver Icon Color Status of the driverRescan Adapters How to rescan?Show Interface If the iconConfiguring the Tsxcusbmbp Driver Interface Tsxcusbmbp Driver Interface WindowWindow Display Select Show InterfaceAddress Changing Process Configuring the Modbus Plus Node AddressAddress Slave Response Configuring the Slave Response TimeoutTimeout Configuration Configured as follows Then Configuring the Virtual Serial COM PortAssignment Configuring Configuring the Modbus Plus RoutingAddressing MethodsImplicit ExplicitDirect Modbus + Slave ID Routing Example Routing exampleModbus Plus Routing Path Node Used by Routing Table Address Application EntryTsxcusbmbp Entering Routing Paths into the Routing Table Configuring the Tsxcusbmbp Driver Modbus Plus Network Status Indicator Connecting to a Modbus Plus NetworkFlash Codes LED Flash Code DescriptionConnecting to a Modbus Plus Network Tsxcusbmbp with an Application Whats in this Chapter? Using the Tsxcusbmbp with an ApplicationStart the Tsxcusbmbp Driver Connect Configure the Application SoftwareIntroduction Typical Configuration Using the Tsxcusbmbp with an Application Section Topic Modbus Plus Network Diagnostic FunctionsModbus Plus Network Diagnostic Functions Procedure for Starting the Diagnostic Functions Starting the Diagnostic FunctionsScanning Local or Complete Network Procedure for Scanning the Modbus Plus NetworkScanning the Modbus Plus Network Introduction Whats in this Section? Displaying Diagnostic InformationModbus Plus Network Diagnostics screen Procedure for Displaying Diagnostic InformationResults ProcedureNode Error Statistics Screennode Node PersonalityTransactions Selected node Screen Internal Path TransactionsToken Owner Work Table Screen Green when active and gray when inactiveMap screen. This section describes this screen Node TokenActive Station Table Token Station Table Present Table Global Data Present TableGlobal Data Read Global DataModbus Plus Network Diagnostic Functions Introduction Whats in this Appendix? AppendicesAppendices This situation from occurring Tsxcusbmbp Settings for UnityTsxcusbmbp Settings for Unity Configuring Unity Make sure both drivers are running You should now be able to Connect Setting Tsxcusbmbp Settings for Concept & ProWORX32Tsxcusbmbp Configuring Concept ProWORX32Step Action