Schneider Electric TSXCUSBMBP user manual Tsxcusbmbp Settings for Concept & ProWORX32

Page 61

TSXCUSBMBP Settings for Concept & ProWORX32

B

TSXCUSBMBP Settings for Concept & ProWORX32

Introduction	This section describes how to configure Concept & ProWORX32 to work the
	TSXCUSBMBP.
Setting the
Setting the	When using serial Modbus communications with Concept, a delay of approximately
Optimum Baud	50 milliseconds occurs before each Modbus request is transmitted.
Rate in Concept	When using Concept with the TSXCUSBMBP, a serial interface must be selected.

	Therefore, the overall throughput of the TSXCUSBMBP with Concept is only slightly
	above that of a serial Modbus interface. Setting the baud rate in Concept to 19200
	instead of the 9600 default will slightly improve performance.
Setting the
Setting the	When using serial Modbus communications with ProWORX32, there are no delays
Optimum Baud	inserted and the TSXCUSBMBP runs at the expected USB speed.
Rate in
ProWORX32

35011984 02/2006

61

Image 61

Contents Tsxcusbmbp Page Table of Contents Using the Tsxcusbmbp with an Application Connecting to a Modbus Plus NetworkModbus Plus Network Diagnostic Functions Appendix a Tsxcusbmbp Settings for UnityImportant Information Safety InformationSchneider Electric. All Rights Reserved At a Glance About the BookAbout the Book Introduction Glossary Abbreviations Acronyms Glossary of Abbreviations AcronymsAbbreviation/Acronym Expansion Abbreviations & Acronyms Subject of this chapter Whats in this Chapter? OverviewTopic Introduction Modbus Plus Communication for ApplicationsVirtual Serial Port VSPTsxcusbmbp Hardware Modbus Plus Network DiagnosticsDescription Overview Subject of this InstallationChapter? Upgrading From Previous Version Installation RequirementsInstalling the Tsxcusbmbp Hardware Installing the Tsxcusbmbp Driver SoftwareIntroduction How to install Tsxcusbmbp Driver? How to install Tsxcusbmbp Hardware Status Establishing a Connection toDriver Icon Color Status of the driverRescan Adapters How to rescan?Show Interface If the iconConfiguring the Tsxcusbmbp Driver Interface Tsxcusbmbp Driver Interface WindowWindow Display Select Show InterfaceAddress Configuring the Modbus Plus Node AddressAddress Changing Process Timeout Configuring the Slave Response TimeoutSlave Response Configuration Configured as follows Assignment Configuring the Virtual Serial COM PortThen Configuring Configuring the Modbus Plus RoutingAddressing MethodsDirect ExplicitImplicit Modbus + Slave ID Routing Example Routing exampleModbus Plus Routing Path Node Used by Routing Table Address Application EntryTsxcusbmbp Entering Routing Paths into the Routing Table Configuring the Tsxcusbmbp Driver Modbus Plus Network Status Indicator Connecting to a Modbus Plus NetworkFlash Codes LED Flash Code DescriptionConnecting to a Modbus Plus Network Tsxcusbmbp with an Application Whats in this Chapter? Using the Tsxcusbmbp with an ApplicationStart the Tsxcusbmbp Driver Introduction Typical Configuration Configure the Application SoftwareConnect Using the Tsxcusbmbp with an Application Section Topic Modbus Plus Network Diagnostic FunctionsModbus Plus Network Diagnostic Functions Procedure for Starting the Diagnostic Functions Starting the Diagnostic FunctionsScanning the Modbus Plus Network Procedure for Scanning the Modbus Plus NetworkScanning Local or Complete Network Introduction Whats in this Section? Displaying Diagnostic InformationModbus Plus Network Diagnostics screen Procedure for Displaying Diagnostic InformationResults ProcedureNode Error Statistics Screennode Node PersonalityTransactions Selected node Screen Internal Path TransactionsToken Owner Work Table Screen Green when active and gray when inactiveMap screen. This section describes this screen Node TokenActive Station Table Token Station Table Present Table Global Data Present TableGlobal Data Read Global DataModbus Plus Network Diagnostic Functions Introduction Whats in this Appendix? AppendicesAppendices Tsxcusbmbp Settings for Unity Tsxcusbmbp Settings for UnityThis situation from occurring Configuring Unity Make sure both drivers are running You should now be able to Connect Setting Tsxcusbmbp Settings for Concept & ProWORX32Tsxcusbmbp Configuring Concept ProWORX32Step Action