Pelco CM6800E-48X8 manual System START-UP, POWER-UP the System, Initialize Keyboards

Page 36

SYSTEM START-UP

After completing the system installation, follow the procedure below to start proper system operation. Skip any “system-specific” steps that do not apply to your system setup.

POWER-UP THE SYSTEM

Plug the CM6800E power cord into a 120/230V, 50/60 Hz power source. Plug in and turn on all devices connected to the CM6800E. Once the system is powered-up you will see video from camera 1 and the following time/date stamp on all system monitors:

Figure 29. CM6800E Time/Date Stamp on Monitor

The time stamp will be advancing in one-second increments. Wait five seconds before proceeding.

INITIALIZE KEYBOARDS

Specify a monitor for each keyboard after your first power-up or any time power is cycled to the keyboard or the CM6800E. Always allow five seconds to elapse before specifying a monitor.

1.Enter a number corresponding to the monitor output that is feeding the monitor you are viewing.

2.Press the MON key. The keyboard LED displays the number you entered. This also confirms successful communication between the keyboard and the CM6800E. If the keyboard LED does not display the monitor number, repeat 1 and 2.

36	C1528M-F (6/05)

Image 36

Contents CM6800E-48X8 Contents Control Genex Multiplexer and Genex Multiplexer Displays List of Illustrations List of Tables C1528M-F 6/05 Important Safeguards and Warnings For Qualified Service Personnel onlyDescription Sample CM6800E-48X8 SystemSample CM6800E 96 x 16 System Sequences, Macros, Presets, Patterns, and Zones System Access and PriorityProgramming KeyboardsAlarm Inputs Power, Mounting MethodsAuxiliary Outputs Continuous Operating DeviceModels Compatible ProductsAdditional Resources Associated EquipmentInstallation Mounting96 x 16 System Default Camera Numbers Video SourcesCable Type Maximum Distance Main unit Cameras Expansion unit CamerasConnecting Looping Video Sources Control Lines 96 x 16 System PTZ Control CapacityMonitors 96 x 16 System Monitor CapacityMain unit Monitor Expansion Unit Monitor Alarms 96 x 16 System Alarm CapacityMain unit Alarms Expansion Unit Alarms Connecting Devices Through the Communication Ports Input Type Wiring Pin-Outs Default DeviceCM9760-MDA, Ascii RS-485 Pin-Outs Ascii device CM9760-MDA, Satellite Rx+ Ground Tx+ RS-232 Pin-Outs RJ-45Port RS-485, 19200 baud, no parity, 8 data bits, 1 stop bitCM6800E Communication Port Connections and Options KBD100, KBD200A, and KBD300A Direct-Powered Keyboards KBD100, KBD200A, and KBD300A Series KeyboardsKeyboard Address Switch Settings Table E. Switch Settings-KBD200A/300A Keyboards OnlyKeyboard Switch OFFKBD100, KBD200A, and KBD300A Remote Keyboards Remote KeyboardsDevices KBD960, ALM2064, REL2064 Devices AddressingKBD960/KBR960 REL2064 ALM2064 Connecting a Single KBD960/KBR960 Keyboard Connecting a KBD960/KBR960 to the CM6800EConnecting a Single ALM2064 Alarm Interface Unit To connect a single ALM2064 Alarm Interface UnitConnecting a Single REL2064 Relay Interface Unit To connect a single REL2064 Relay Interface UnitMultiple M Devices Multiple M Devices Local ConnectionConnecting Multiple M Devices Remote Connection Multiple M Devices Remote ConnectionConnecting a PC PC Connection to RJ-45 PortConnecting Genex Multiplexers Connecting Genex MultiplexersConnecting Relay Contacts AUX 1 Local Auxiliaries96 x 16 System Auxiliary Capacity Main unit AUX Expansion Unit AUXConnecting the Open Collector Output F3 TTL Wiring the F3 TTL OutputConnecting a 96 X 16 System CM6800E-48X8 Main UnitPOWER-UP the System System START-UPInitialize Keyboards Configure the System Port Default SettingsCommunication Ports COM96 X 16 System Settings KBD960/KBR960 KeyboardGenex Multiplexer Control MUXMonitor Color Adjustment Program PresetsAdditional Programming Programming the CM6800E CM6800E Programming Mode Exit Programming ModeSelect Language Entries in Programming Mode FunctionKeyboard Navigate to the Help field Press F1 Navigate to the Next or Previous field Press F1Access Keyboard to MonitorCamera to Keyboard Camera to MonitorAlarm Programming Program Alarm GroupsProgram AN Internal or External Alarm Contact AUX field, select an auxiliary to be activated ACK TypeType PriorityProgram a Video Loss Alarm Program Video Loss AlarmsAssign a Logical Alarm Number Optional Assign a Logical Alarm NumberAlarm-based Operation Mode field for each auxiliary, select either LAT or MOMAuxiliary Outputs Latching or Momentary OperationCamera Programming Program Logical NumbersIf necessary, first program logical camera number Program Cameras Program Vertical Drive Option Optional Select CharacterEvent Timers Macros Macro Status View ScreenMonitor Display MonitorCamera Title Type Display ValuesMonitor Status Display Values ALM Status Display ValuesTime DatePassword Use the Set Password screen to change the system passwordPorts SERIAL/COM Ports Serial Port Input on CM6800E rear panelAction Ascii text Priority PortOptions Level 1 = highest priority Level 8 = lowest priority96 X 16 System Settings Change the System SettingSequences SequenceAUX and ## Turn global auxiliary onTurn global auxiliary off Turn camera auxiliary onPATTERNS, PRESETS, and Zones Time and DateOptions DD/MMM/YY MMM/DD/YY YY/MMM/DD DD/MM/YY YY/MM/DD Switch Monitors OperationOverview Operating the CM6800EControl Receivers Operate Sequences To move through the sequence one camera at a timeRUN a Macro Select Macro to start the macroSelect To start the macro Acknowledge AN Alarm Call a PresetCreate and RUN a Pattern Patterns are not available with the KBD100 keyboardOperate AUXILIARIES/RELAYS Operate a Local AuxiliaryOperate an External Auxiliary Operate an Auxiliary in a ReceiverControl Genex Multiplexer and Genex Multiplexer Displays Operate Scanning FunctionsDetect Video Loss Define ZonesCM6800E DIP Switches CM6800E DIP Switch Default SettingSwitch AppendixAlarm Group Display Options Monitor Alarm AlarmsBlock Build Chronological Pair D and QMonitor Alarm Alarms Next Display Cycle Reverse Chronological Pair M and LSalvo Group Macro Commands Description Specify FieldsAuxiliary Notes Pipo QuadNano HEXInstall the CM6800E AS a Satellite Device Page Configure the CM6800E AS a Satellite Device Satellite Monitor AccessSatellite Port Settings Change the Port SettingSatellite Alarms Optional Enable Alarm ContactsConfigure CM9700-MGR System Manager Settings Add a Satellite Device in the CM9700-MGRConfigure CM9760-MGR System Manager Settings Program the Comms File Click the Comms tab. The Comms page appearsProgram the Cameras File Click the Cameras tab. The Cameras page appearsProgram the Link Cameras File Click the Link Cameras tab. The Link Cameras page appearsProgram the Alarms File Optional Click the Alarms tab. The Alarms page appearsClick OK to close the Alarm Camera Switches dialog box How to Display the CM6800E Programming Main Menu How to Exit Programming ModeHow to Select a Numerical Value in an Option Field Press 89 PresetLogical Number Assignment Table for Link Cameras Link Camera NameLink Camera page Phy Num column Ascii Operating Commands Functional Procedure Commands Result3Ma16#a Desired Action Command Result Uppercase characters48~Jva Trigger an alarm #Ea Clear an alarm #IaAcknowledge an alarm #Ka Panel An alarm is triggered #Ea Logical Alarm Number in the Alarm Programming sectionTroubleshooting Gaining Initial ControlWait AT Least Five Seconds Software Reset Dip Switch Cover PlateSolutions to Common Problems Problem RemedyKBD960/KBR960 ICON/BUTTON Legend Icon/Button LegendUpgrade the CM6800 Switcher Software Upgrade the CM6800 Switcher SoftwareGlossary Term DefinitionAscii Ntsc PALPTZ All four wires Star configurationRS-422 Recommended distance is 4,000 feet 1,219 mSpecifications Regulatory Notices 48 x 8 System96 x 16 System Product Warranty and Return Information C1528M-F 6/05 105 ISO9001

Related manuals

Manual 20 pages 33.51 Kb