Pelco C2622M FX82051 module consists of the following series of models, Multimode Models

Page 7

Designed to meet NEMA TS 2 and Caltrans traffic signal control equipment standards for ambient operating temperature, mechanical shock and vibration, humidity with condensation, high-line/low-line voltage conditions, and transient voltage protection

NOTE: Conformal coating is required for operation in environments with relative humidity above 95 percent (condensing).

No performance adjustments required

12 VDC or 24 VAC power supply

Stand-alone and rack-mountable modular design

LED indicators for monitoring of optic signal/laser status, 100BASE-FX port status including far end fault indication (FEFI), 10BASE-T/100BASE-TX port status, and operating power

MODELS

The FX82051 module consists of the following series of models:

Multimode Models*

FX82051MSTR-2 Unmanaged Ethernet switch, five 10BASE-T/100BASE-TX ports, one multimode ST fiber port, two fibers

FX82051MSCR-2 Unmanaged Ethernet switch, five 10BASE-T/100BASE-TX ports, one multimode SC fiber port, two fibers

Single-Mode Models*†

FX82051SSTR-2 Unmanaged Ethernet switch, five 10BASE-T/100BASE-TX ports, one single- mode ST fiber port, two fibers

FX82051SSCR-2 Unmanaged Ethernet switch, five 10BASE-T/100BASE-TX ports, one single- mode SC fiber port, two fibers

*For conformal coated models, replace the first letter F in the model number with the letter C. The conformal coated version of FX82051MSTR-2, for example, is CX82051MSTR-2.

Single-mode FC connector is available upon request. Contact the factory for additional information.

OPTIONAL ACCESSORIES

The following optional accessories are available:

WM5002-3U

Wall mount base kit for double-width module

WM5002-3UEXP

Wall mount expansion kit for double-width module

RK5000-3U

19-inch rack mount chassis for 14 slots (no power), 3 RUs

RK5000PS-3U

19-inch rack mount chassis for 12 slots with power, 3 RUs

EPS5000-120

External rack power supply, 1 RU, dual 120 W power outputs

RK5001B-3U

Blank filler panel, single width

RK5002B-3U

Blank filler panel, double width

RK5002-1UEXP

Adapter kit that allows a 3 RU double-width fiber module to be used in

 

RK5000PS-5U rack mount chassis

C2622M (2/07)

7

Image 7
Contents Ethernet Switch List of Illustrations ContentsList of Tables Important Safety Instructions Risk of Electric Shock Do not Open Radio and Television Interference Regulatory NoticesDescription Product OverviewSingle-Mode Models*† ModelsFX82051 module consists of the following series of models Multimode ModelsFront Panel Power LED Pelco badge100BASE-FX Status LED Rear Panel 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectorsPackage Contents InstallationFlow control is disabled by default Autonegotiation is enabled by defaultFlow control default setting Table A. TX Mode Switch Settings10BASE-T/100BASE-TX Modes of Operation Mounting the FX82051 Module Into a Rack MountingMounting the FX82051 Module Using the Wall Clip 10BASE-T/100BASE-TX connections ConnectionsFiber connections Fiber Port Connections in Point-to-Point Application Troubleshooting Meaning Possible Cause Corrective Action Optic Fault LED Amber Table C. Troubleshooting with Rear-Panel IndicatorsDesired, refer to Setting Data is being Desired, refer to Setting Transmitted orMeaning Possible Cause Corrective Action Amber Port is set to If 10BASE-T full-duplex Duplex modeDuplex mode Duplex link If half-duplex mode isUse Cat5e or higher Green Port is set to If 100BASE-TX full-duplexFlashing green Port is set to Normal or excessive Replace cable if it isTable C. Troubleshooting with Rear-Panel Indicators Duplex/collision and speed SpecificationsFX82051SSTR-2 Optical Maximum LaserIllustrates RJ-45 MDI/MDI-X connector pinouts Appendix. RJ-45 Connector PinoutsProduct Warranty and Return Information ISO9001