Sun Microsystems EC000066 manual Changing the Solaris root password

Page 47

CHANGING THE SOLARIS ROOT PASSWORD

■ no data errors are reported See the example below:

# zpool status

pool: vtlpool0

state: ONLINE
scrub: none requested
config:
NAME	STATE	READ WRITE CKSUM
vtlpool0		0	0	0
vtlpool0	ONLINE	0	0	0
raidz1		0	0	0
raidz1	ONLINE	0	0	0
c0t0d0	ONLINE	0	0	0
c0t1d0	ONLINE	0	0	0
c0t2d0		0	0	0
c0t2d0	ONLINE	0	0	0
c0t3d0	ONLINE	0	0	0
c0t4d0	ONLINE	0	0	0
c0t5d0		0	0	0
c0t5d0	ONLINE	0	0	0
c0t6d0	ONLINE	0	0	0

spares

c0t7d0	AVAIL
c1t7d0	AVAIL
c7t7d0	AVAIL

c4t7d0	AVAIL
errors: No known data errors
errors: No known data errors

Alternatively, to limit the output to problem pools only, use the following form of the command:

#zpool status -xv

3.Once you have finished your checks, close the terminal window. Next task: “Changing the Solaris root password” on page 35.

Changing the Solaris root password

You should not leave the system system configured with the default Solaris root password or share the default with the customer. Instead, change the default password to something the customer prefers. Proceed as follows.

316196101 • A

Chapter 2 Setting up the VTL Value ILOM service processor 35

Image 47

Contents Virtual Tape Library Page Revision History Iv VTL Value Hardware Installation Guide Aug Contents Setting up the VTL Value Ilom service processor Removing VTL Value hardware Viii VTL Value Hardware Installation Guide Aug About this book Using this bookUnderstanding the conventions used in this book Taking advantage of this book’s hypertext featuresCommenting on this book Xii VTL Value Hardware Installation Guide Aug Installing the VTL Value appliance in an equipment rack Installing VTL Value hardwareObtaining required tools, personnel, and materials Remove both power supplies Remove the system controllerPreparing the slide-rail assemblies for installation Installing slide-rail assembliesAttaching the inner rails to the server chassis Positioning the outer/middle rail assembly in the rack VTL Value Hardware Installation Guide Aug 316196101 a Attaching the outer/middle rail assembly to the rack 316196101 a Sun Rack 1000 hardware uses metric screws Adjusting and securing middle/outer slide rails VTL Value Hardware Installation Guide Aug Mounting the appliance in the rack VTL Value Hardware Installation Guide Aug 316196101 a Installing VTL Value hardware Cabling Installing the cable management armAttaching the Outer Rail Extension VTL Value Hardware Installation Guide Aug 316196101 a Installing VTL Value hardware Installing data and power cables Routing and connecting cablesPort Starting the VTL appliance Powering up316196101 a Installing VTL Value hardware Powering down Understanding the Ilom Setting up the VTL Value Ilom service processorAttaching a laptop to the Ilom via the VTL private network Changing the IP address of the Ilom SPNext task Changing the IP address of the Ilom on Changing the IP address of the Ilom Resetting the default Ilom password Changing the Ilom passwordChecking the health of the internal storage systems Java starts, downloads files, and launches the Java console Accessing the Solaris desk top via the IlomRoot Running basic storage diagnostics Submirror 0 d31 No data errors are reported See the example below Changing the Solaris root passwordLogging out of the operating system and Ilom Changing the default Solaris root passwordLogging out 316196101 a VTL Value Hardware Installation Guide Aug Back and front panels VTL Value server Top hard disk drive or fan fault VTL private network addresses VTL Value Hardware Installation Guide Aug Connecting to Ilom via a serial port Log in to the CLI as root and enter the root password Ilom command reference Display information about PET alerts. You can NtpIPaddress VTL Value Hardware Installation Guide Aug Removing VTL Value hardware Shutting off system powerRemoving the cable management arm Removing the appliance from the rack Removing the VTL appliance from a rackPreparing to remove the appliance VTL Value Hardware Installation Guide Aug