Sun Microsystems 816-7727-10 manual Power button Standby Keyswitch Normal Locked Diagnostics

Page 53

2.Turn on power to any peripherals and external storage devices.

Read the documentation supplied with the device for specific instructions.

3.Connect the Sun Fire V440 server’s outlet plug of each power cord to the power sequencer in the cabinet (if your type of cabinet includes one), to a grounded outlet strip, or to a grounded AC power outlet.

Note – Each outlet must connect the server to a 15A circuit for North America and Japan, and to a 10A or 16A circuit for Europe. Consult your local electrical codes for any additional requirements. See the instructions provided with your cabinet for information about the power sequencer.

Note – Connect each cord to a separate circuit to maximize system availability.

The Standby LEDs on the power supplies are lit, indicating that power is being supplied. As soon as you plug in the power cord, several boot messages from the ALOM software are displayed on your system console device. The ALOM boot messages end with the ALOM sc> prompt.

4.Unlock and open the right system door, as viewed from the front of the system.

5.Insert the system key into the system control keyswitch and turn the system control keyswitch to the Diagnostics position.

See the Sun Fire V440 Server Administration Guide for information about each system control keyswitch setting.

The illustration below shows the system control keyswitch and the Power button locations, as well as the keyswitch position icons.

Power button

Standby

Keyswitch

Normal

Locked

Diagnostics

Chapter 3 Setup and Power-On Procedures 45

Image 53

Contents Sun Fire V440 Server Installation Guide Please Recycle Contents Background and Reference Setup and Power -On ProceduresHow This Book Is Organized PrefaceTypographic Conventions Using Unix CommandsRelated Documentation System PromptsSun Welcomes Your Comments Accessing Sun DocumentationContacting Sun Technical Support About the Parts Shipped to You Preparing for InstallationVerify that you have received all the parts of your system Verify All PartsTransfer Online Documentation Plan the InstallationWhat Next Installing a Sun Fire Server Into a 4-Post Cabinet Checklist of 4-Post Rackmounting Tasks Inventory for 4-Post Rackmounting Tools Required for Rackmounting Attach the Inner Glides to the Chassis Remove the side panels from the cabinet, if applicable Prepare the CabinetLocate the Mounting Holes To use the Rack Alignment template, complete these steps Install the Slide Assemblies Sun Fire V440 Server Installation Guide July Installing a Sun Fire V440 Server Into a 4-Post Cabinet Install the Server Into the Cabinet Installing a Sun Fire V440 Server Into a 4-Post Cabinet Sun Fire V440 Server Installation Guide July What Next Install the Cable Management Arm Captive screw Slot Tab Mounting hole Inner glide Sun Fire V440 Server Installation Guide July Installing a Sun Fire V440 Server Into a 4-Post Cabinet Locate the speed pin on the end of the cable management arm Secure the Cords and Cables to the Cable Management Arm Upper lip Velcro straps Oval cutouts First section Oval cutouts Install any optional components shipped with your system Install Optional ComponentsPort Information Connecting the Cords and CablesConnect the Power Cords to the Server PCI Connect Twisted-Pair Ethernet Cables Choose a network port, using the following table as a guideInstalling a Sun Fire V440 Server Into a 4-Post Cabinet Restore the Cabinet Set Up a System Console Device Setup and Power-On ProceduresAbout Connecting the Server to a Terminal Server Terminal Straight-through cable Server Turn off power to the alphanumeric terminal Open a terminal session on the connecting device, and typeHow to Access the System Console via tip Connection A terminal window on the other Sun system, type Choose a host name for the server and make a note of it Prepare to Configure the Primary Network InterfacePower On the Server How to Power On via the Power Button Turn the system control keyswitch to the Locked position How to Power On via the poweron CommandPower button Standby Keyswitch Normal Locked Diagnostics Quickly enter the console command sc console At the Alom sc prompt, type the poweron command sc poweronSetup and Power-On Procedures What Next System LEDs Background and ReferenceFollowing table describes the power supply LEDs Serial Port Connector Signals Serial Port ConnectorTable A-44-Post Cabinet Requirements Post Cabinet RequirementsTable A-44-Post Cabinet Requirements Sun Fire V440 Server Installation Guide July