Sun Microsystems X2100 manual You will hear an audible click

Page 20

Mounting bracket inserted into slide-rail

Slide-rail	Slide-rail
release	assembly
button	mounted on
	rack post

FIGURE 1-7Inserting the Server With Mounting Brackets Into the Slide-Rails

4.Simultaneously pull and hold the slide-rail release buttons on each mounting bracket while you push the server into the rack. (See FIGURE 1-7.) Continue pushing until the slide-rail locks on the front of the mounting brackets engage the slide-rail assemblies.

You will hear an audible click.

Caution – Before continuing to the next procedure, verify that the server is securely mounted in the rack and that the slide-rail locks are engaged with the mounting brackets.

1-10Sun Fire X2100 Server Getting Started Guide • April 2006

Image 20

Contents Sun Fire X2100 Server Getting Started Guide Please Recycle Contents Software Installation Setting Up the Preinstalled SoftwareContents Vi Sun Fire X2100 Server Getting Started Guide May Preface How This Book Is OrganizedShell Prompts Typographic ConventionsRelated Documentation Third-Party Web Sites Sun Welcomes Your CommentsSystem Setup Safety and Compliance InformationPlanning the Installation Process StartPackage Contents Inventory Installing the Server Into a Rack With Optional Slide-Rails Disassembling the Slide-Rails Before Installation Unpack the slide-railsInstalling the Mounting Brackets Onto the Server 3Aligning the Mounting Bracket With the Server ChassisRepeat and for the remaining slide-rail assembly Attaching the Slide-Rail Assemblies to the Rack5Setting the Rail Width Installing the Server Into the Slide-Rail Assemblies 6Extending the Anti-tip FootYou will hear an audible click Installing the Cable Management Assembly 12Sun Fire X2100 Server Getting Started Guide April Right slide-rail CMA mounting bracket Right slide- rail assembly CMA slide-rail connector System Setup Install cables to your server, as required Attaching and Routing CablesPosition the cable hangers snap them into place. See Route the cables through the CMA cable hangersCabling the Server Verifying Operation of the Slide-Rails and CMABack Panel Interconnecting Servers 15Interconnecting ServersPowering On the Server Front PanelPowering Off the Server Using Serial Console Redirection Eeprom console=text /usr/dt/bin/dtconfig -e 24Sun Fire X2100 Server Getting Started Guide April Software Installation Preparing for Installation1Installation Flow Diagram Setting up the Bios for Windows 2003 or Solaris 10 OS Erasing the Primary Boot Hard DiskSetting up the Bios for Operating System Installation Installing the Operating System Setting up the Bios for a Linux Operating SystemRunning the up2date Utility Installing Drivers and Mounting the Diagnostic Partition Installing the Drivers Over a NetworkCreate a Shared Drivers Directory Change to the /etc/dfs directoryOpen the dfstab file in a text editor Add the following line to the dfstab fileAt the command prompt type /export/home/drivers directory is now on the network asLog in as root superuser on the hostname system Add the following line to the end of the dfstab fileType the following command at the prompt Create a Shared Drivers Directory on a Windows SystemCopy the Drivers from the Supplemental CD Iii. Select Map Network Drive Install the Drivers onto the Target Sun Fire X2100 ServerLogin as superuser Type the following at the command line Install the Drivers on a Target Windows System Type the appropriate command to install the driversInstalling Linux Operating System Drivers From a CD Log in to the Sun Fire X2100 Server as superuserRun the installation script by typing the following command Log in as superuser Installing Solaris 10 OS Operating System Drivers from a CDType the following command at the system prompt Run the install script by typing the following command Installing RAID Drivers Using the 2003Reburn Script Installing RAID Drivers Using a Boot Diskette Where OS is 200332 or Installing Windows 2003 Drivers Specify the driver location as C\NVIDIA\Ethernet 22Sun Fire X2100 Server Getting Started Guide April Solaris 10 Operating System Configuration Overview Solaris 10 Operating System1Installation Process Flow Diagram Configuration Instructions Reboot the system1Information for Preinstalled Solaris 10 Configuration Java Enterprise System Http//docs.sun.com Sun Studio Software Http//docs.sun.com8Sun Fire X2100 Server Getting Started Guide April P E N D I X a \ risetup.exe Adding the Nvida Ethernet Drivers to the Windows Image Adding Other Drivers and Modifying Setting Files Remove the following entry from the ristndrd.sif fileAdd the following entries to the ristndrd.sif file Unattended DriverSigningPolicy = IgnoreTo unzip the package, type the following command \ net Stop binlsvc c\ net Start binlsvc Installing Windows 2003 Server 64-bit onto the RIS Server Ultra20WindowsXP64-bit 10Sun Ultra 20 Workstation Getting Started Guide April Drivers audio nic sataide smbus OemDir \ copy cdromdrive\drivers\windows\xp64\chipset\*.zip c\temp Installing a RIS Image onto a Client Server Either power on or reboot the server14Sun Ultra 20 Workstation Getting Started Guide April