Sun Microsystems X2100 manual Installing Windows 2003 Server 64-bit onto the RIS Server

Page 72

A.2 Creating a RIS Image of Windows 2003 Server, 64-bit, and Platform Drivers

This section tells you how to create a Windows 2003 Server 64-bit image on a RIS server and then add platform specific drivers to the image. All drivers for this procedure located on the Supplemental CD, version 1.3 or later.

Note – Before using this procedure, you must install RIS onto a Windows 2003 server. See the following URL for complete instructions on how to install the RIS.

http://support.microsoft.com/default.aspx?scid=kb;en-us;325862

A.2.1 Installing Windows 2003 Server 64-bit onto the RIS Server

To copy the Windows 2003 Server 64-bit CD onto the RIS server, do the following steps. Click Next or Finished in each screen to advance to the next screen.

1.Insert the Windows 2003 Server 64-bit CD into the RIS server's CDROM drive.

2.In the Start menu, select Run.

3.To start the RIS setup program, type the following command:

c:\ risetup.exe

Note – In all commands, c:\ is shown as the DOS command prompt.

4.In the “Welcome to the Remote Installation Services Setup Wizard“ screen, click Next.

5.In the “Remote Installation Services Options“ screen, choose “Add a new OS image to this remote installation server“.

6.In the “Installation Source Files Location” screen, choose the CDROM drive with the Windows 2003 Server 64-bit CD.

A-8Sun Ultra 20 Workstation Getting Started Guide • April 2006

Image 72

Contents Sun Fire X2100 Server Getting Started Guide Please Recycle Contents Software Installation Setting Up the Preinstalled SoftwareContents Vi Sun Fire X2100 Server Getting Started Guide May Preface How This Book Is OrganizedShell Prompts Typographic ConventionsRelated Documentation Third-Party Web Sites Sun Welcomes Your CommentsSystem Setup Safety and Compliance InformationPlanning the Installation Process StartPackage Contents Inventory Installing the Server Into a Rack With Optional Slide-Rails Disassembling the Slide-Rails Before Installation Unpack the slide-railsInstalling the Mounting Brackets Onto the Server 3Aligning the Mounting Bracket With the Server ChassisRepeat and for the remaining slide-rail assembly Attaching the Slide-Rail Assemblies to the Rack5Setting the Rail Width Installing the Server Into the Slide-Rail Assemblies 6Extending the Anti-tip FootYou will hear an audible click Installing the Cable Management Assembly 12Sun Fire X2100 Server Getting Started Guide April Right slide-rail CMA mounting bracket Right slide- rail assembly CMA slide-rail connector System Setup Install cables to your server, as required Attaching and Routing CablesPosition the cable hangers snap them into place. See Route the cables through the CMA cable hangersCabling the Server Verifying Operation of the Slide-Rails and CMABack Panel Interconnecting Servers 15Interconnecting ServersPowering On the Server Front PanelPowering Off the Server Using Serial Console Redirection Eeprom console=text /usr/dt/bin/dtconfig -e 24Sun Fire X2100 Server Getting Started Guide April Software Installation Preparing for Installation1Installation Flow Diagram Erasing the Primary Boot Hard Disk Setting up the Bios for Operating System InstallationSetting up the Bios for Windows 2003 or Solaris 10 OS Installing the Operating System Setting up the Bios for a Linux Operating SystemRunning the up2date Utility Installing Drivers and Mounting the Diagnostic Partition Installing the Drivers Over a NetworkCreate a Shared Drivers Directory Change to the /etc/dfs directoryOpen the dfstab file in a text editor Add the following line to the dfstab fileAt the command prompt type /export/home/drivers directory is now on the network asLog in as root superuser on the hostname system Add the following line to the end of the dfstab fileType the following command at the prompt Create a Shared Drivers Directory on a Windows SystemCopy the Drivers from the Supplemental CD Install the Drivers onto the Target Sun Fire X2100 Server Login as superuser Type the following at the command lineIii. Select Map Network Drive Install the Drivers on a Target Windows System Type the appropriate command to install the driversInstalling Linux Operating System Drivers From a CD Log in to the Sun Fire X2100 Server as superuserRun the installation script by typing the following command Installing Solaris 10 OS Operating System Drivers from a CD Type the following command at the system promptLog in as superuser Run the install script by typing the following command Installing RAID Drivers Using the 2003Reburn Script Installing RAID Drivers Using a Boot Diskette Where OS is 200332 or Installing Windows 2003 Drivers Specify the driver location as C\NVIDIA\Ethernet 22Sun Fire X2100 Server Getting Started Guide April Solaris 10 Operating System Configuration Overview Solaris 10 Operating System1Installation Process Flow Diagram Configuration Instructions Reboot the system1Information for Preinstalled Solaris 10 Configuration Java Enterprise System Http//docs.sun.com Sun Studio Software Http//docs.sun.com8Sun Fire X2100 Server Getting Started Guide April P E N D I X a \ risetup.exe Adding the Nvida Ethernet Drivers to the Windows Image Adding Other Drivers and Modifying Setting Files Remove the following entry from the ristndrd.sif fileAdd the following entries to the ristndrd.sif file Unattended DriverSigningPolicy = IgnoreTo unzip the package, type the following command \ net Stop binlsvc c\ net Start binlsvc Installing Windows 2003 Server 64-bit onto the RIS Server Ultra20WindowsXP64-bit 10Sun Ultra 20 Workstation Getting Started Guide April Drivers audio nic sataide smbus OemDir \ copy cdromdrive\drivers\windows\xp64\chipset\*.zip c\temp Installing a RIS Image onto a Client Server Either power on or reboot the server14Sun Ultra 20 Workstation Getting Started Guide April