Sun Microsystems X2100 manual Where OS is 200332 or

Page 53

■A Windows 2003 CD (retail media only—not an OEM version)

To create a boot diskette for Windows 2003 32-bit and 64-bit, you need a Windows system with a CD drive and a diskette drive.

1.On a Windows system, insert the Sun Fire X2100 Server Supplemental CD.

2.Change to the following directory on the CD:

D:\DRIVERS\WINDOWS\OS\CHIPSET

Where OS is 2003_32 or 2003_64.

3.Unzip the appropriate file under the CHIPSET directory and extract the files to a local directory (for example C:\raid).

■For 2003_32, unzip the NFref_*_w2k.zip

■For 2003_64, unzip CK804_*_w64.zip

4.Insert a preformatted blank diskette into the server.

5.Change to the directory where the files were extracted (for example, C:\raid), then open the appropriate directory for your OS.

For 2003_32, open IDE\WinXP\

For 2003_64, open IDE\Win2k\sataide

6.Select all files in the directory and copy them to the diskette drive (a:).

7.Configure RAID in the Sun Fire X2100 Server BIOS.

a. Reboot the server and press the F2 key when you see the Sun logo screen. The BIOS Setup screen is displayed.

b. Select Integrated Peripherals from the main menu. c. Select RAID config.

d. Under RAID, change the setting to Enable.

e. Press the F10 key to save your changes and exit.

8.When prompted by the NVRaid BIOS, press the F10 key. a. Select the type of RAID (mirror or stripe).

b. Select the disk drives for the array. c. Press the F7 key.

d. Select boot (B).

e. Exit the NVRaid BIOS.

f. Press Control-X to save and exit the NVRaid BIOS.

Chapter 2 Software Installation 2-19

Image 53

Contents Sun Fire X2100 Server Getting Started Guide Please Recycle Contents Setting Up the Preinstalled Software Software InstallationContents Vi Sun Fire X2100 Server Getting Started Guide May How This Book Is Organized PrefaceTypographic Conventions Shell PromptsRelated Documentation Sun Welcomes Your Comments Third-Party Web SitesSafety and Compliance Information System SetupStart Planning the Installation ProcessPackage Contents Inventory Installing the Server Into a Rack With Optional Slide-Rails Unpack the slide-rails Disassembling the Slide-Rails Before Installation3Aligning the Mounting Bracket With the Server Chassis Installing the Mounting Brackets Onto the ServerAttaching the Slide-Rail Assemblies to the Rack Repeat and for the remaining slide-rail assembly5Setting the Rail Width 6Extending the Anti-tip Foot Installing the Server Into the Slide-Rail AssembliesYou will hear an audible click Installing the Cable Management Assembly 12Sun Fire X2100 Server Getting Started Guide April Right slide-rail CMA mounting bracket Right slide- rail assembly CMA slide-rail connector System Setup Attaching and Routing Cables Install cables to your server, as requiredPosition the cable hangers snap them into place. See Route the cables through the CMA cable hangersVerifying Operation of the Slide-Rails and CMA Cabling the ServerBack Panel 15Interconnecting Servers Interconnecting ServersFront Panel Powering On the ServerPowering Off the Server Using Serial Console Redirection Eeprom console=text /usr/dt/bin/dtconfig -e 24Sun Fire X2100 Server Getting Started Guide April Preparing for Installation Software Installation1Installation Flow Diagram Setting up the Bios for Windows 2003 or Solaris 10 OS Erasing the Primary Boot Hard DiskSetting up the Bios for Operating System Installation Setting up the Bios for a Linux Operating System Installing the Operating SystemRunning the up2date Utility Installing the Drivers Over a Network Installing Drivers and Mounting the Diagnostic PartitionChange to the /etc/dfs directory Create a Shared Drivers DirectoryOpen the dfstab file in a text editor Add the following line to the dfstab file/export/home/drivers directory is now on the network as At the command prompt typeLog in as root superuser on the hostname system Add the following line to the end of the dfstab fileCreate a Shared Drivers Directory on a Windows System Type the following command at the promptCopy the Drivers from the Supplemental CD Iii. Select Map Network Drive Install the Drivers onto the Target Sun Fire X2100 ServerLogin as superuser Type the following at the command line Type the appropriate command to install the drivers Install the Drivers on a Target Windows SystemLog in to the Sun Fire X2100 Server as superuser Installing Linux Operating System Drivers From a CDRun the installation script by typing the following command Log in as superuser Installing Solaris 10 OS Operating System Drivers from a CDType the following command at the system prompt Run the install script by typing the following command Installing RAID Drivers Using the 2003Reburn Script Installing RAID Drivers Using a Boot Diskette Where OS is 200332 or Installing Windows 2003 Drivers Specify the driver location as C\NVIDIA\Ethernet 22Sun Fire X2100 Server Getting Started Guide April Solaris 10 Operating System Solaris 10 Operating System Configuration Overview1Installation Process Flow Diagram Reboot the system Configuration Instructions1Information for Preinstalled Solaris 10 Configuration Java Enterprise System Http//docs.sun.com Http//docs.sun.com Sun Studio Software8Sun Fire X2100 Server Getting Started Guide April P E N D I X a \ risetup.exe Adding the Nvida Ethernet Drivers to the Windows Image Remove the following entry from the ristndrd.sif file Adding Other Drivers and Modifying Setting FilesUnattended DriverSigningPolicy = Ignore Add the following entries to the ristndrd.sif fileTo unzip the package, type the following command \ net Stop binlsvc c\ net Start binlsvc Installing Windows 2003 Server 64-bit onto the RIS Server Ultra20WindowsXP64-bit 10Sun Ultra 20 Workstation Getting Started Guide April Drivers audio nic sataide smbus OemDir \ copy cdromdrive\drivers\windows\xp64\chipset\*.zip c\temp Either power on or reboot the server Installing a RIS Image onto a Client Server14Sun Ultra 20 Workstation Getting Started Guide April