Sun Microsystems 440 manual To cause the changes to take effect, type

Page 44

Note – There are many other OpenBoot configuration variables. Although these variables do not affect which hardware device is used to access the system console, some of them affect which diagnostic tests the system runs and which messages the system displays at its console. For details, refer to the Netra 440 Server Diagnostics and Troubleshooting Guide (817-3886-xx).

7.To cause the changes to take effect, type:

ok reset-all

The system stores the parameter changes, and boots automatically when the OpenBoot configuration variable auto-boot?is set to true (its default value).

Note – To store parameter changes, you can also power cycle the system using the front panel Power button.

You can issue system commands and view system messages using your local graphics monitor. Continue with your installation or diagnostic procedure, as needed.

If you want to redirect the system console back to the serial management and network management ports, see “System Console OpenBoot Configuration Variable Settings” on page 31.

30 Netra 440 Server System Administration Guide • August 2004

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Netra 440 Server System Administration Guide Page Contents Managing RAS Features and System Firmware Managing Disk Volumes Iv Netra 440 Server System Administration Guide August Figures Vi Netra 440 Server System Administration Guide August Tables Viii Netra 440 Server System Administration Guide August Preface How This Book Is OrganizedUsing Unix Commands Shell PromptsTypographic Conventions Related DocumentationAccessing Sun Documentation Third-Party Web SitesContacting Sun Technical Support Sun Welcomes Your CommentsConfiguring the System Console Communicating With the System1Ways of Communicating With the System Using the System Console What the System Console DoesSerial MGT NET MGT Alom serial management port Alom network management port Alternative System Console Configuration 3Alternative Console Ports Require Additional ConfigurationAccessing the System Console Through a Graphics Monitor About the sc Prompt Reaching the sc Prompt OpenBoot ok PromptAccess Through Multiple Controller Sessions Reaching the ok Prompt L1-A Stop-A Keys or Break Key Alom System Controller break or console CommandGraceful Shutdown Externally Initiated Reset XIR Manual System ResetFor More Information Getting to the ok Prompt2Ways of Accessing the ok Prompt To Get to the ok PromptConsole # Accessing the System Controller Using the Serial Management PortEstablish an Alom system controller session Activating the Network Management PortTo Use the Serial Management Port Log out of the Alom system controller session To verify the network settings, typeTo Activate the Network Management Port Accessing the System Console Through a Terminal Server To Access The System Console Through a Terminal Server3Pin Crossovers for Connecting to a Typical Terminal Server Open a terminal session on the connecting device, and type Accessing the System Console Through a TIP Connection Power on the systemTo Access the System Console Through the TIP Connection A shell tool window on the Sun system, typeOk power-off To Modify the /etc/remote File If the number displayed by the uname -rcommand is less thanModifying the /etc/remote File Netra 440 Server System Administration Guide August Ok setenv input-device ttyb ok setenv output-device ttyb Verifying Serial Port Settings on Ttyb To Verify the Serial Port Settings on TtybOpen a shell tool window Type Look for the following outputFor more information, see Getting to the ok Prompt on To cause the changes to take effect, type System Console OpenBoot Configuration Variable Settings Output-device Ttya Ttyb Screen Input-device KeyboardNetra 440 Server System Administration Guide August Managing RAS Features and System Firmware Alom System Controller Logging In To the Alom System ControllerAbout the scadm Utility To Log In To the Alom System ControllerTo View Environmental Information Sc showenvironmentControlling the Locator LED To turn on the Locator LED, do one of the followingTo turn off the Locator LED, do one of the following OpenBoot Emergency Procedures Stop-N Functionality To Restore OpenBoot Configuration DefaultsStop-A Functionality Automatic System Recovery To reset the system, type the following commandStop-F Functionality Stop-D FunctionalityAuto-Boot Options Error Handling Summary Reset Scenarios Automatic System Recovery User CommandsEnabling and Disabling Automatic System Recovery To Enable Automatic System RecoveryTo cause the parameter change to take effect, type To Disable Automatic System RecoveryTo cause the parameter changes to take effect, type To Unconfigure a Device Manually Unconfiguring and Reconfiguring DevicesObtaining Automatic System Recovery Information To determine full physical device paths, type To Reconfigure a Device Manually To Enable the Hardware Watchdog Mechanism Enabling the Hardware Watchdog Mechanism and Its OptionsMultipathing Software Managing Disk Volumes Disk VolumesSun StorEdge Traffic Manager Volume Management SoftwareVeritas Dynamic Multipathing Managing Disk Volumes RAID Technology Disk ConcatenationRAID 0 Disk Striping RAID 1 Disk MirroringHot-Spares Hardware Disk MirroringRAID 5 Disk Striping With Parity To Create a Hardware Disk Mirror C1t3d0 Devices/pci@1f,700000/scsi@2/sd@3,0For example To Delete a Hardware Disk Mirror To delete the volume, type the following command To confirm a failed disk, type the following command To Perform a Mirrored Disk Hot-Plug OperationTo Perform a Non-Mirrored Disk Hot-SwapOperation View the status of the Scsi devices CD-ROMRemove the hard drive from the device tree # cfgadm -x removedevice c0dsk/c1t1d0Configure the new hard drive Verify that the device has been removed from the device treeVerify that the new hard drive is in the device tree OpenBoot Configuration Variables Baudrate, bits Appendix a OpenBoot Configuration Variables Netra 440 Server System Administration Guide August Alarm Relay Output Application Programming Interface Netra 440 Server System Administration Guide August Page Netra 440 Server System Administration Guide August Page Netra 440 Server System Administration Guide August Symbols IndexNetra 440 Server System Administration Guide August Asr-disable, 46 go Console, 11, 41 console -f, 9 poweroff, 12 poweron Uadmin 11 uname, 25 uname -r Netra 440 Server System Administration Guide August
Top Page Image Contents