Sun Microsystems 440 manual Accessing the System Console Through a Terminal Server

Page 33

To connect through the network management port, use the telnet command to the IP address you specified in Step 3 of the preceding procedure.

Accessing the System Console Through a Terminal Server

The following procedure assumes that you are accessing the system console by connecting a terminal server to the serial management port (SERIAL MGT) of the Netra 440 server.

To Access The System Console Through a Terminal Server

1.Complete the physical connection from the serial management port to your terminal server.

The serial management port on the Netra 440 server is a data terminal equipment (DTE) port. The pinouts for the serial management port correspond with the pinouts for the RJ-45 ports on the Serial Interface Breakout Cable supplied by Cisco for use with the Cisco AS2511-RJ terminal server. If you use a terminal server made by another manufacturer, check that the serial port pinouts of the Netra 440 server match those of the terminal server you plan to use.

If the pinouts for the server serial ports correspond with the pinouts for the RJ-45 ports on the terminal server, you have two connection options:

Connect a serial interface breakout cable directly to the Netra 440 server. See “Accessing the System Controller” on page 16.

Connect a serial interface breakout cable to a patch panel and use the straight- through patch cable (supplied by Sun) to connect the patch panel to the server.

Chapter 1 Configuring the System Console 19

Image 33
Contents Netra 440 Server System Administration Guide Page Contents Managing RAS Features and System Firmware Managing Disk Volumes Iv Netra 440 Server System Administration Guide August Figures Vi Netra 440 Server System Administration Guide August Tables Viii Netra 440 Server System Administration Guide August How This Book Is Organized PrefaceShell Prompts Using Unix CommandsRelated Documentation Typographic ConventionsThird-Party Web Sites Accessing Sun DocumentationContacting Sun Technical Support Sun Welcomes Your CommentsCommunicating With the System Configuring the System Console1Ways of Communicating With the System What the System Console Does Using the System ConsoleSerial MGT NET MGT Alom serial management port Alom network management port 3Alternative Console Ports Require Additional Configuration Alternative System Console ConfigurationAccessing the System Console Through a Graphics Monitor About the sc Prompt OpenBoot ok Prompt Access Through Multiple Controller SessionsReaching the sc Prompt Reaching the ok Prompt Alom System Controller break or console Command Graceful ShutdownL1-A Stop-A Keys or Break Key Manual System Reset Externally Initiated Reset XIRGetting to the ok Prompt For More InformationTo Get to the ok Prompt 2Ways of Accessing the ok PromptConsole # Using the Serial Management Port Accessing the System ControllerActivating the Network Management Port To Use the Serial Management PortEstablish an Alom system controller session To verify the network settings, type To Activate the Network Management PortLog out of the Alom system controller session To Access The System Console Through a Terminal Server Accessing the System Console Through a Terminal Server3Pin Crossovers for Connecting to a Typical Terminal Server Open a terminal session on the connecting device, and type Power on the system Accessing the System Console Through a TIP ConnectionA shell tool window on the Sun system, type To Access the System Console Through the TIP ConnectionOk power-off If the number displayed by the uname -rcommand is less than Modifying the /etc/remote FileTo Modify the /etc/remote File Netra 440 Server System Administration Guide August Ok setenv input-device ttyb ok setenv output-device ttyb To Verify the Serial Port Settings on Ttyb Verifying Serial Port Settings on TtybOpen a shell tool window Type Look for the following outputFor more information, see Getting to the ok Prompt on To cause the changes to take effect, type Output-device Ttya Ttyb Screen Input-device Keyboard System Console OpenBoot Configuration Variable SettingsNetra 440 Server System Administration Guide August Managing RAS Features and System Firmware Logging In To the Alom System Controller Alom System ControllerTo Log In To the Alom System Controller About the scadm UtilitySc showenvironment To View Environmental InformationTo turn on the Locator LED, do one of the following Controlling the Locator LEDTo turn off the Locator LED, do one of the following OpenBoot Emergency Procedures To Restore OpenBoot Configuration Defaults Stop-A FunctionalityStop-N Functionality To reset the system, type the following command Automatic System RecoveryStop-F Functionality Stop-D FunctionalityAuto-Boot Options Error Handling Summary Automatic System Recovery User Commands Reset ScenariosEnabling and Disabling Automatic System Recovery To Enable Automatic System RecoveryTo Disable Automatic System Recovery To cause the parameter changes to take effect, typeTo cause the parameter change to take effect, type Unconfiguring and Reconfiguring Devices Obtaining Automatic System Recovery InformationTo Unconfigure a Device Manually To determine full physical device paths, type To Reconfigure a Device Manually Enabling the Hardware Watchdog Mechanism and Its Options To Enable the Hardware Watchdog MechanismMultipathing Software Disk Volumes Managing Disk VolumesVolume Management Software Veritas Dynamic MultipathingSun StorEdge Traffic Manager Managing Disk Volumes Disk Concatenation RAID TechnologyRAID 1 Disk Mirroring RAID 0 Disk StripingHardware Disk Mirroring RAID 5 Disk Striping With ParityHot-Spares C1t3d0 Devices/pci@1f,700000/scsi@2/sd@3,0 To Create a Hardware Disk MirrorFor example To Delete a Hardware Disk Mirror To delete the volume, type the following command To Perform a Mirrored Disk Hot-Plug Operation To confirm a failed disk, type the following commandTo Perform a Non-Mirrored Disk Hot-SwapOperation CD-ROM View the status of the Scsi devices# cfgadm -x removedevice c0dsk/c1t1d0 Remove the hard drive from the device treeVerify that the device has been removed from the device tree Configure the new hard driveVerify that the new hard drive is in the device tree OpenBoot Configuration Variables Baudrate, bits Appendix a OpenBoot Configuration Variables Netra 440 Server System Administration Guide August Alarm Relay Output Application Programming Interface Netra 440 Server System Administration Guide August Page Netra 440 Server System Administration Guide August Page Netra 440 Server System Administration Guide August Index SymbolsNetra 440 Server System Administration Guide August Asr-disable, 46 go Console, 11, 41 console -f, 9 poweroff, 12 poweron Uadmin 11 uname, 25 uname -r Netra 440 Server System Administration Guide August