Sun Microsystems X4150 manual 2shows the RAID drive options, 2RAID Drive Options

Page 71

Note – Configuring the Sun Fire X4150 server RAID is optional, by default, the preinstalled Windows Server 2003 R2 image is configured in a non-RAID configuration. If anything other than a basic Mirror RAID is required, it is recommended to perform a fresh install of the Windows Server 2003 R2 OS in the desired RAID configuration.

RAID Drive Options

TABLE 5-2shows the RAID drive options:

TABLE 5-2RAID Drive Options

SAS Card	Drives Supported	RAID Configuration Supported	Drive Usage

Sun StorageTek	Seagate 73 GB SAS	Volume – 1 disk
	Fujitsu 73 GB SAS	RAID 0 – stripe – 2 disk minimum	No redundancy
	Seagate 146 GB SAS	RAID 1 – mirror – 2 disk minimum	50%
		RAID 1E – 3 drive minimum	50%
		RAID – 4 drive minimum	50%
		RAID 5 – 3 drive minimum	67–94%
		RAID 5EE – 4 drive minimum	50–88%
		RAID 50 – 6 drive minimum	67–94%
		RAID 6 – 4 drive minimum	50–88%
		RAID 60 – 8 drive minimum	50–88%
		Spanned Volume – 2 drive minimum	100%
		RAID Volume – 4 drive minimum	50-100%
LSI 3081E	Seagate 73 GB SAS	IM – Integrated Mirror array. 2 disk	Data on Primary disk
		minimum, plus up to 2 hot spare disks.	might be merged.
	Fujitsu 73 GB SAS	IME – Integrated Mirror Enhanced array. 3	All data will be deleted
		to 8 disks including up to 2 hot spares.	during creation.
	Seagate 146 GB SAS	IS – Integrated Striping array. 2 to 8 disks.	All data will be deleted
			during creation.

Chapter 5 Configuring the Preinstalled Windows Server 2003 R2 Operating System

61

Image 71

Contents Sun Fire X4150 Server Installation Guide Please Recycle Contents Configuring the Preinstalled Solaris 10 Operating System Setting Up the Sun Fire X4150 ServerIf You Need Help Vi Sun Fire X4150 Server Installation Guide May How This Book Is Organized Table P-1Installation Guide ChaptersSun Online Typographic ConventionsRelated Documentation Safety and Compliance InformationSun Fire X4150 Server Documentation Sun Welcomes Your Comments Tools and Equipment Needed Installation Process Flowchart1Sun Fire X4150 Server Installation Process Part 2Sun Fire X4150 Server Installation Process Part Options Package Contents InventoryUnpacking the Boxes Antistatic Precautions Sun Fire X4150 Server Description Front Panel Features2Back Panel Legend Back PanelSun Fire X4150 Server Installation Guide May Server Installation Process Overview Before You Install the Server1Rack Compatibility Service LabelChecking Compatibility Disassembling Slide-Rails Preparing the Slide Rails and Server for InstallationUnpack the slide-rails 1Disassembling the Bolt-onSlide-rail Before Installation2Aligning the Mounting-bracket With the Server Chassis Installing the Mounting-Brackets Onto the ServerAttaching Bolt-On Slide-Rail Assemblies Attaching the Slide-Rail Assemblies to the RackSlide-rail assembly Rack post Rail-width spacer 5Extending the Anti-tip Foot Installing the Server Into the Slide-Rail AssembliesSun Fire X4150 Server Installation Guide May 7Cable Management Arm CMA Installing the Cable Management ArmLeft slide-rail CMA rail extension Remove tape to separate partsLeft slide-rail CMA rail extension Right slide-rail CMA mounting bracket Right slide- rail assembly CMA slide-rail connector 12Connecting the CMA Arm to the Rail Extension Connector Install and route cables to your server, as requiredCMA arm CMA cable hanger Verifying Operation of the Slide-rails and CMA Setting Up the Sun Fire X4150 Server Connector Locations Connecting the CablesCabling the Server 2Front Panel Power/OK LEDEmbedded LOM Service Processor Software Overview Service Processor OverviewClient-side Secure 2Embedded LOM Service Processor ComponentsRemote Console ApplicationIntegrated LOM Service Processor Software Overview Initial LOM Setup Overview Connecting to the LOM Service Processor for the First TimePower on the server or restart the server if it is running Determining the LOM Service Processor IP AddressMethod 1 Access the Bios See -4for the position of the serial port on the back panel Be sure to record the IP address assigned to the LOM Method 1 Using the Bios Modifying the Service Processor IP AddressExample Method 2 Using the Serial ConnectionIlom Set /SP/network IPSource=dhcp Applying Power for the First Time Install and configure the software, as required Installing the Intel Proset Teaming Utility Sun Fire X4150 Server Installation Guide May Delivery Methods Solaris Preinstall OverviewAbout the Grub Menu Before You Begin1Installation Worksheet Installation WorksheetNIS+ Start the LOM console. Elom Configuring the Solaris OSRedirect the Console Output to the Video Port Optional Using the Grub MenuCtrl-A Configuring Sun Fire X4150 Server RAID DrivesReboot the server RAID Drive Overview3RAID Drive Options RAID Drive OptionsMirroring the Preinstalled Solaris OS with LSI RAID Using your Solaris Server, log in and start Xserver Solaris 10 Operating System User Information Accessing Solaris 10 User DocumentationSolaris 10 OS Training Downloading Solaris 10 OS SoftwareWindows Server 2003 R2 Preinstall Overview Boot the pre-installation image for the first time Configuring the Windows Server 2003 R2 Operating SystemHow to start a Rkvm Session Determine the Service Processor IP addressDate and Time Settings screen appears Workgroup or Computer Domain page appears 2RAID Drive Options 2shows the RAID drive optionsSun Fire X4150 Server Installation Guide May You will need the Sun Fire X4150 Server Tools and Drivers CD One more confirmation screen appears. Confirm the mirroring Power On the Main Power Powering On and Off the Server1Front Panel Power/OK LED Power Off from Main Power Mode2Troubleshooting Procedures Setup Troubleshooting3System Information Needed for Support Contacting Support4Sun Technical Support Contacts 4Sun Technical Support Contacts Index Sun Fire X4150 Server Installation Guide May

Related manuals

Manual 12 pages 7.65 Kb

Manual 150 pages 45 Kb