Sun Microsystems X4150 manual See -4for the position of the serial port on the back panel

Page 45

2.When the Sun Microsystems splash screen or text prompt appears during the Power On Self Test (POST) operation, press F2 to access the BIOS settings.

3.Navigate to the Server tab, using the left and right keyboard arrows.

4.Access the Server tab and AST2000 (LAN)CONFIGURATION. Press Enter.

5.Access the IP ADDRESS tab.

6.View the SP IP address.

Tip – If the IP address is in the form of 192.168.xxx.xxx, the DHCP server might not have assigned an address and the SP might use a static address.

Method 2: Connect to the Service Processor Using a Serial Connection

To establish a connection to the SP using a serial connection (system management port), perform the following steps:

1.Connect a terminal (or PC running terminal emulation software) to the server serial port.

2.Ensure that the server hardware is installed and cables are inserted.

Ensure that the power is in standby mode and the green LED blinks. See “Connecting the Cables” on page 28.

3.Verify that your terminal, laptop, PC, or terminal server is operational.

4.Configure the terminal device or the terminal emulation software running on a laptop or PC to the following settings:

8,N,1: eight data bits, no parity, one stop bit

9600 baud

Disable hardware flow control (CTS/RTS)

Disable software flow control (XON/XOFF)

5.Connect a null serial modem cable from the RJ45 serial port on the server back panel to a terminal device (if not connected already).

See FIGURE 1-4for the position of the serial port on the back panel.

6.Press Enter on the terminal device to establish a connection between the terminal device and the LOM service processor (SP).

Chapter 3 Setting Up the Sun Fire X4150 Server

35

Image 45
Contents Sun Fire X4150 Server Installation Guide Please Recycle Contents Configuring the Preinstalled Solaris 10 Operating System Setting Up the Sun Fire X4150 ServerIf You Need Help Vi Sun Fire X4150 Server Installation Guide May How This Book Is Organized Table P-1Installation Guide ChaptersSun Online Typographic ConventionsSafety and Compliance Information Sun Fire X4150 Server DocumentationRelated Documentation Sun Welcomes Your Comments Tools and Equipment Needed Installation Process Flowchart1Sun Fire X4150 Server Installation Process Part 2Sun Fire X4150 Server Installation Process Part Package Contents Inventory Unpacking the BoxesOptions Antistatic Precautions Sun Fire X4150 Server Description Front Panel Features2Back Panel Legend Back PanelSun Fire X4150 Server Installation Guide May Server Installation Process Overview Before You Install the ServerService Label Checking Compatibility1Rack Compatibility Disassembling Slide-Rails Preparing the Slide Rails and Server for InstallationUnpack the slide-rails 1Disassembling the Bolt-onSlide-rail Before Installation2Aligning the Mounting-bracket With the Server Chassis Installing the Mounting-Brackets Onto the ServerAttaching Bolt-On Slide-Rail Assemblies Attaching the Slide-Rail Assemblies to the RackSlide-rail assembly Rack post Rail-width spacer 5Extending the Anti-tip Foot Installing the Server Into the Slide-Rail AssembliesSun Fire X4150 Server Installation Guide May 7Cable Management Arm CMA Installing the Cable Management ArmLeft slide-rail CMA rail extension Remove tape to separate partsLeft slide-rail CMA rail extension Right slide-rail CMA mounting bracket Right slide- rail assembly CMA slide-rail connector 12Connecting the CMA Arm to the Rail Extension Connector Install and route cables to your server, as requiredCMA arm CMA cable hanger Verifying Operation of the Slide-rails and CMA Setting Up the Sun Fire X4150 Server Connector Locations Connecting the CablesCabling the Server 2Front Panel Power/OK LEDEmbedded LOM Service Processor Software Overview Service Processor OverviewRemote Console 2Embedded LOM Service Processor ComponentsApplication Client-side SecureIntegrated LOM Service Processor Software Overview Initial LOM Setup Overview Connecting to the LOM Service Processor for the First TimeDetermining the LOM Service Processor IP Address Method 1 Access the BiosPower on the server or restart the server if it is running See -4for the position of the serial port on the back panel Be sure to record the IP address assigned to the LOM Method 1 Using the Bios Modifying the Service Processor IP AddressExample Method 2 Using the Serial ConnectionIlom Set /SP/network IPSource=dhcp Applying Power for the First Time Install and configure the software, as required Installing the Intel Proset Teaming Utility Sun Fire X4150 Server Installation Guide May Delivery Methods Solaris Preinstall OverviewAbout the Grub Menu Before You Begin1Installation Worksheet Installation WorksheetNIS+ Start the LOM console. Elom Configuring the Solaris OSRedirect the Console Output to the Video Port Optional Using the Grub MenuReboot the server Configuring Sun Fire X4150 Server RAID DrivesRAID Drive Overview Ctrl-A3RAID Drive Options RAID Drive OptionsMirroring the Preinstalled Solaris OS with LSI RAID Using your Solaris Server, log in and start Xserver Solaris 10 Operating System User Information Accessing Solaris 10 User DocumentationSolaris 10 OS Training Downloading Solaris 10 OS SoftwareWindows Server 2003 R2 Preinstall Overview How to start a Rkvm Session Configuring the Windows Server 2003 R2 Operating SystemDetermine the Service Processor IP address Boot the pre-installation image for the first timeDate and Time Settings screen appears Workgroup or Computer Domain page appears 2RAID Drive Options 2shows the RAID drive optionsSun Fire X4150 Server Installation Guide May You will need the Sun Fire X4150 Server Tools and Drivers CD One more confirmation screen appears. Confirm the mirroring Power On the Main Power Powering On and Off the Server1Front Panel Power/OK LED Power Off from Main Power Mode2Troubleshooting Procedures Setup Troubleshooting3System Information Needed for Support Contacting Support4Sun Technical Support Contacts 4Sun Technical Support Contacts Index Sun Fire X4150 Server Installation Guide May
Related manuals
Manual 12 pages 7.65 Kb Manual 150 pages 45 Kb