Paradyne 9126-II, CSU, DSU manual PVC Connection Options 2, Source Edlci, Primary Destination Link

Page 113

4. Configuration Options

Table 4-15. PVC Connection Options (2 of 4)

Source EDLCI

Possible Settings: 0 – 62

Default Setting: Initially blank; no default.

Specifies the source Embedded Data Link Connection Identifier (EDLCI) for a frame relay interface when a multiplexed DLCI record is selected as one end of a connection.

Display Conditions – This option only appears when Source DLCI contains a multiplexed DLCI record number.

0 – 62 – Specifies the EDLCI number.

Primary Destination Link

Possible Settings: Net1-FR1,ISDN Link Name, Rtr-S0

Default Setting: Initially blank; no default.

Specifies the frame relay interface used as the primary destination link; the to end of a from-to link. The only valid settings for this configuration option are frame relay interfaces that have at least one DLCI or EDLCI defined which are not part of a PVC connection or management link. For example, if the network interface has no DLCIs defined, Net1-FR1 would not appear as a valid setting.

Net1-FR1– Specifies the Network interface as the destination link.

ISDN Link Name – For units with ISDN backup capability, specifies the ISDN link of the DBM as the destination of the connection. This can be any nonnull link name configured on an ISDN frame relay link.

Rtr-S0– For the FrameSaver SLV 9126-II Router, specifies the virtual router port as the destination link.

Primary Destination DLCI

Possible Settings: 16 – 1007

Default Setting: Initially blank; no default.

Specifies the primary destination DLCI for a frame relay interface. The DLCI must be defined and cannot be part of a PVC connection or management link. For multiplexed DLCIs, at least one EDLCI must be unconnected for the DLCI to be a valid selection.

NOTES:

–Primary Destination DLCI has no value if Primary Destination Link contains no value.

–When an ISDN DBM is installed and the DLCI assigned to the PVC is in a Backup Group (see Table 4-14, DLCI Record Options), the letter designation assigned to the group of DLCIs appears next to the primary destination DLCI number on the Management PVCs Options screen.

16 – 1007 – Specifies the DLCI number.

9128-A2-GB20-80

September 2002

4-69

Image 113

Contents FrameSaver SLV Copyright 2002 Paradyne Corporation All rights reserved Warranty, Sales, Service, and Training InformationDocument Feedback TrademarksContents September ConfigurationTProceduresConfiguration Options Iii Configuring the FrameSaver SLV RouterOperation and Maintenance Security and LoginsTroubleshooting Lamp Test Setting Up Network Health for FrameSaver Devices Setting Up NetScout Manager Plus for FrameSaver DevicesMenu HierarchyT ViiViii Snmp MIBs and Traps, and Rmon Alarm DefaultsRouter CLI TCommands, Codes, and Designations Connectors, Cables, and Pin Assignments Router Command Line Summaries and ShortcutsIndex Technical Specifications Equipment ListSection Description Purpose and Intended AudienceDocument Organization Section Description XiiDocument Number Document Title Product-Related DocumentsXiii Xiv Conventions UsedSystem Overview About the FrameSaver SLVRouter-Specific Features CSU/DSU-Specific FeaturesAbout the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Through 120 Connections PVCs Dedicated Management FrameSaver SLV Feature RouterMaximum Number of PVCs and Management PVCs Supported About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II FeaturesFrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On ProcedureIf your login was Hen Select Main MenuScreen Format Description Screen Work AreasPress Navigating the ScreensKeyboard Keys For the screen Select Function Press Enter to Function KeysSelecting from a Menu Switching Between Screen AreasEntering Information Screen ContentsSelecting a Field CLI Keyboard Keys Navigating the Router’s CLIBasic Configuration Configuration ProceduresIsdn Configuration MenuConfiguration Option Area Description Configuration Option AreasMain Menu → Configuration Accessing and Displaying Configuration OptionsConfiguration → PVC Connections Changing Configuration OptionsSaving Configuration Options Configuration Options Configuration Options Easy Install Screen Example Using the Easy Install FeatureMain Menu → Easy Install Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUsIf the selection is Enter Entering System Information and Setting the System ClockMain Menu → Control→ System Information Setting Up Call Directories for Trap Dial-Out Setting Up the ModemMain Menu → Control→ Modem Call Directories Valid characters include ForSetting Up to Use the Modem PassThru Feature Auto-Configuration Screen Example Setting Up Auto-ConfigurationMain Menu → Auto-Configuration Main Menu → Auto-Configuration→Frame Relay Discovery Mode Selecting a Frame Relay Discovery ModeDiscovery Mode Configuration Description Only applies to models withDiscovery Mode Configuration Description Automatically Removing a Circuit Main Menu → Configuration → Isdn → Physical Setting Up Dial BackupSetting Up the DBM Physical Interface If you select Then Setting Up Automatic Backup ConfigurationFollowing prompt When Appears If you select Destinations Remove AlternateFrom PVCs Delete unusedModifying Isdn Link Profiles Main Menu → Configuration → Isdn → Link ProfilesFor Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup TimersAssigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp TrapsSetting Up Back-to-Back Operation PVC Backup Over the Network InterfaceChanging Operating Mode Main Menu → Control→ Change Operating ModeConfiguration Option Tables Configuring Frame Relay and LMI for the System CSU/DSUs Configuring the Overall SystemMain Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 1System Frame Relay and LMI Options 2 System Frame Relay and LMI Options 3 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsClass of Svc Name Class of Service DefinitionsMeasure Latency & Availability Code Points AssignedCode Point Definitions Code Point DefinitionsCode Pnt NameService Level Verification Options 1 Configuring Service Level Verification OptionsSLV Type Available Settings Standard, COS 1-COS SLV Sample Interval secsDlci Down on SLV Timeout Service Level Verification Options 2SLV Timeout Error Event Threshold SLV Timeout Clearing Event ThresholdSLV Packet Size bytes Service Level Verification Options 3SLV Latency Clearing Event Threshold Main Menu → Configuration → System→ General Configuring General System OptionsTest Timeout General System Options 1General System Options 2 General System Options 3 System Alarm RelayConfiguring the Network Interface Configuring Physical InterfacesMain Menu → Configuration → Network→ Physical Network Physical Interface Options 1Network Physical Interface Options 2 Line Build Out LBO Possible Settings 0.0, -7.5, -15Bit Stuffing Transmit TimingNetwork Physical Interface Options 3 Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Initiated PLB Ansi Performance Report MessagesCircuit Identifier Network Physical Interface Options 4Main Menu → Configuration → Data Ports→ Physical Configuring a User Data Port CSU/DSUsPort Use Possible Settings Frame Relay, Synchronous Data Data Port Physical Interface Options 1Max Port Rate Kbps Data Port Physical Interface Options 2Port Base Rate Kbps Transmit Clock SourceMonitor DTR Data Port Physical Interface Options 3Monitor RTS Control Invert Transmit and Receive Data Data Port Physical Interface Options 4Port DTE Initiated Loopbacks Data Port Physical Interface Options 5 Action on Network Yellow AlarmMain Menu → Configuration → DSX-1 Configuring the DSX-1 InterfaceDSX-1 Physical Interface Options 1 Interface StatusSend All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2Service Profile ID Spid 1 or Configuring the Isdn DBM InterfaceIsdn BRI DBM Physical Interface Options Local Phone Number 1 orLocal Phone Number Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS10. Isdn PRI DBM Physical Interface Options 1 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Main Menu → Configuration → Isdn → Isdn Link Profiles Setting Up Isdn Link Profiles11. Isdn Link Profile Options 1 Link NameOutbound Phone Number 11. Isdn Link Profile Options 2Inbound Calling ID 1 or Maximum Link Rate Kbps11. Isdn Link Profile Options 3 Assigning Time Slots/Cross ConnectionsCaller Identification Method Alternate Outbound Phone NumberValue Meaning Assigning Frame Relay Time Slots to the Network InterfaceFrame Relay Network Time Slot Assignment Screen Example Ntt Assigning DSX-1 Time Slots to the Network InterfaceTime Slot Assignment Rule Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen ExampleDSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen ExamplePhysical Interface Options Clearing AssignmentsLMI Configuring Frame Relay for an Interface13. Interface Frame Relay Options 1 Traffic Policing 13. Interface Frame Relay Options 2LMI Parameters Frame Relay DS0s Base Rate13. Interface Frame Relay Options 3 Dlci Number Manually Configuring Dlci Records14. Dlci Record Options 1 Committed Burst Size Bc Bits 14. Dlci Record Options 2CIR bps Excess Burst Size Bits 14. Dlci Record Options 3Dlci Priority Outbound Management Priority14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, NoneMain Menu → Configuration → PVC Connections Configuring PVC Connections15. PVC Connection Options 1 Source DlciSource Edlci 15. PVC Connection Options 2Primary Destination Link Primary Destination DlciPrimary Destination Edlci 15. PVC Connection Options 3Alternate Destination Link Alternate Destination DlciAlternate Destination Edlci 15. PVC Connection Options 4Main Menu → Configuration → IP Path List Static Configuring the IP Path List16. IP Path List Enter IP Address press ESC to abort ... FWD NoSetting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information17. Node IP Options 2 TS Access Management LinkTS Management Snmp Validation 17. Node IP Options 318. Management PVC Options 1 Configuring Management PVCsSet DE 18. Management PVC Options 2Payload Managed Primary Dlci 18. Management PVC Options 3Primary Edlci 18. Management PVC Options 4Alternate Edlci 18. Management PVC Options 5Alternate Dlci Encapsulation 18. Management PVC Options 6Name 1 Access Configuring General Snmp Management19. General Snmp Management Options 1 Snmp Management19. General Snmp Management Options 2 Configuring Telnet and/or FTP Session SupportName 2 Access Telnet Session Telnet Login Required20. Telnet and FTP Session Options 1 20. Telnet and FTP Session Options 2 21. Snmp NMS Security Options 1 Configuring Snmp NMS SecurityNMS IP Validation Number of Managers22. Snmp Traps and Trap Dial-Out Options 1 Configuring Snmp Traps and Trap Dial-Out21. Snmp NMS Security Options 2 22. Snmp Traps and Trap Dial-Out Options 2 Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both22. Snmp Traps and Trap Dial-Out Options 3 22. Snmp Traps and Trap Dial-Out Options 4 Possible Settings Network, Ports, DBM, All, NoneDlci Traps on Interfaces Filter Selection Field Rmon Traps22. Snmp Traps and Trap Dial-Out Options 5 Dial-Out Delay TIme MinTrap Dial-Out Trap DisconnectAlternate Dial-Out Directory 22. Snmp Traps and Trap Dial-Out Options 6Latency Traps IP SLV Availability Traps23. Ethernet Management Options 1 Configuring Ethernet ManagementProxy ARP 23. Ethernet Management Options 2Character Length Configuring the Communication Port24. Communication Port Options 1 24. Communication Port Options 2 Login RequiredParity Stop Bits24. Communication Port Options 3 RIP 24. Communication Port Options 4100 Configuring the Modem Port24. Communication Port Options 5 25. Modem Port Options 125. Modem Port Options 2 10125. Modem Port Options 3 10225. Modem Port Options 4 103Main Menu → Configuration → Auto Backup Criteria Configuring the Criteria for Automatic Backup26. Auto Backup Criteria Options 1 104When Auto Backup Allowed 26. Auto Backup Criteria Options 2Backup Allowed Day From nnnn Backup Allowed Day To nnnn106 Configuring the FrameSaver SLV Router Ethernet FrameSaver SLV Router OverviewNetwork Interface Proxy ARP Address Resolution ProtocolIP Routing Interface Configuration Applications Supported by NAT Network Address TranslationIP Options Processing NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration ExampleSave exit Napt Mapping Public IP Address Private IP Addresses Napt Configuration ExampleNetwork Address Port Translation Int ethernet 0 ip nat inside int serial 0.x ip nat outside Access-list 1 permit 10.1.3.0Ip nat inside source list 1 interface se 0.x overload Ip nat inside source static 10.1.1.1 NAT and Napt Configuration ExampleDynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration ExampleDhcp Relay Agent Dhcp Server at Remote Site Configuration ExampleBridge Filtering Router SecurityIP Router Filtering IP Filtering Provisioning the Router InterfaceLand Bug Prevention Smurf Attack PreventionConfiguring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting AccessSet the configuration option Limiting Dial-In Access via the Modem Port Isdn Call Security Controlling Isdn AccessDisabling Isdn Access Limiting Telnet Access Controlling Telnet or FTP AccessLimiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp AccessAssigning Snmp Community Names and Access Levels Main Menu → Configuration → Limiting Snmp Access Through IP AddressesGeneral Snmp Management → Snmp Management Enable Management and Communication →Field Enter Creating a LoginMain Menu → Control→ Administer Logins Deleting a Login Modifying a LoginLargo Controlling Router CLI AccessAccess Levels Command Modes Enable Changing Access LevelsEnable password password EndSecurity and Logins September Operation and Maintenance Operation and Maintenance View this field To find Displaying System InformationMain Menu → Status → Identity Isdn DBM Viewing LEDs and Control LeadsFrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLVDisplay LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control LeadsMain Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control LeadsGeneral Status LEDs 1 LED DescriptionsLabel Indiction Color What It Means ALMContd General Status LEDs 2Model 9128-IILabel Indication Color What It Means Network, DSX, or PRI Interface LEDsUser Data Port LED CSU/DSUs Only Ethernet Port LED Routers OnlyAdditional Control Leads Label Indication What It Means Control Lead DescriptionsNetwork Interface User Data PortDevice Messages 1 What It Indicates What To Do Device MessagesSeen at an FTP TerminalSee Changing Software on Device Messages 2 What It Indicates What To DoPVC Device Messages 3 What It Indicates What To DoDevice Messages 4 What It Indicates What To Do Device Messages 5 What It Indicates What To Do Reset COM Port usageFrameSaver SLV II onlyDevice Messages 6 What It Indicates What To Do Status Menu Example Status InformationSystem and Test Status Messages Last System Reset Date and TimeMain Menu → Status → System and Test Status Self-Test Results MessagesHealth and Status Messages Change Operating ModeHealth and Status Messages 1 What It Indicates Isdn PRI DBM onlyFrameSaver SLV 9126-II or Health and Status Messages 2 What It IndicatesFrame relay link 1,2 Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It IndicatesHealth and Status Messages 5 What It Indicates Series Access Carrier onlyPathIP Address Down Nnnn, framerelaylink 1,2Health and Status Messages 6 What It Indicates Relay Network Assignments and an LMI failure is Configuration→ Time Slot Assignment → FrameHealth and Status Messages 7 What It Indicates Test Status Messages 1 What It Indicates Test Status MessagesDclb Active, framerelaylink 1 or Framerelaylink 1 ,3Test Status Messages 2 What It Indicates LMI-Reported DLCIs Status Screen Example Network LMI-Reported DLCIs StatusMain Menu → Status→ LMI Reported DLCIs Tframe relay network, or IP Path Connection Status Screen Example IP Path Connection StatusMain Menu → Status→ IP Path Connection Status 11. IP Path Connection Status Field What It Indicates PVC Connection Status Screen Example PVC Connection StatusMain Menu → Status→ PVC Connection Status Edlci 12. PVC Connection Status 1 Field What It IndicatesMgmtPVCName Status What It Indicates 12. PVC Connection Status 2 FieldDisplaying Network Time Slot Assignments Time Slot Assignment StatusMain Menu → Status→ Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen ExampleDisplaying DSX-1 Time Slot Assignments Cross Connect Status Field bottom IndicatesMain Menu → Status→ Timeslot Assignment Status→ DSX-1 DSX-1 Timeslot Assignment Status Screen ExampleDBM Interface Status Screen Example DBM Interface StatusMain Menu → Status→ DBM Interface Status Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It Indicates13. DBM Interface Status 2 Field What It Indicates Link Name DisabledAwarded and Being Delivered In Est Chnl-7Value is Call Awarded 13. DBM Interface Status 3 Field What It IndicatesBeing Delivered In Est Chnl-7Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance Main Menu → Status→ IP Routing Table IP Routing TableIP Routing Table Screen Example 15. IP Routing Table Values 1 Column What It IndicatesTTL 15. IP Routing Table Values 2 Column What It IndicatesPerformance Statistics Menu Performance StatisticsMain Menu → Status→ Performance Statistics Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance StatisticsVerification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration OptionsSize is changed, a new average is not available until a new 18. Dlci Performance Statistics 1 What It Indicates Dlci Performance StatisticsMain Menu → Status → Performance Statistics→ Dlci 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci Main Menu → Status → Performance Statistics→ Frame Relay Frame Relay Performance StatisticsFor FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 1 What It Indicates20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay ErrorsFrame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc ErrorsTo select intervals You must enter an interval or time on ESF Line Performance StatisticsMain Menu → Status → Performance Statistics→ ESF Line Lofc ESF Line Performance Statistics Screen ExampleLofc UAS22. DBM Call Performance Statistics What It Indicates DBM Call Performance Statistics23. Ethernet Performance Statistics What It Indicates Ethernet Performance StatisticsMain Menu → Status → Performance Statistics → Ethernet Trap Event Log Screen Example Trap Event LogMain Menu → Status → Trap Event Log Canceling Modem PassThru Operation Activating the Modem PassThru FeatureMain Menu → Control→ Enable Modem PassThru to COM Main Menu → Control→ Disable Modem PassThru to COMMain Menu → Control→ Disconnect Modem Manually Disconnecting the ModemVerifying Modem Operation Isdn DBM Operation Forcing Backup DisruptiveIf the Result is Then Placing a Test Call NondisruptiveMain Menu→ Test→ Isdn Call/PVC Tests System Operational should appear Verifying That Backup Can Take PlaceVerifying Isdn Lines FTP File Transfers Command Definition If the message displayed is Then Upgrading System SoftwareMain Menu → Status→ Identity Upgrading Isdn BRI DBM SoftwareMain Menu → Control→ Select Software Release Determining Whether a Download Is CompletedChanging Software If retrieving Hen Transferring Collected DataMain Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm RelayOperation and Maintenance September Troubleshooting Indicators See Problem IndicatorsOperation and Maintenance Main Menu → Status → Display LEDs and Control LEDsResetting the Unit By Cycling the Power Resetting the Unit and Restoring CommunicationResetting the Unit from the Control Menu If selecting He following occurs Restoring Communication with an Improperly Configured UnitLMI Packet Capture Utility Feature Troubleshooting Management Link FeatureLMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace LogMenu → Control → Reset Device AlarmsAlarm Conditions 1 What It Indicates What To Do Main Menu → Configuration → Isdn → Link Profiles Alarm Conditions 2 What It Indicates What To DoName IPAddressMenu→ Configuration→ Alarm Conditions 3 What It Indicates What To DoLMI Down, frame relay LinkDTE Alarm Conditions 4 What It Indicates What To DoPathIP Address Alarm Conditions 5 What It Indicates What To DoNnnn , frame relay Alarm Conditions 6 What It Indicates What To DoAlarm Conditions 7 What It Indicates What To Do Device Problems Troubleshooting TablesDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event LogImproperly Configured Unit on Device Problems 2 Symptom Possible Cause SolutionsFrame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC ProblemsMain Menu → Status → DBM Interface Status Isdn DBM ProblemsIsdn DBM Problems Symptom Possible Cause Solutions Test Menu Example Tests AvailableDBM Tests Test Timeout FeatureStarting and Stopping a Test When the status of a test is Only command available isAborting All Tests PVC Tests Screen Example PVC TestsMain Menu → Test→ Network PVC Test PVC LoopbackMain Menu → Test→ Data Port PVC Tests Main Menu → Test→ Isdn Call/PVC TestsMonitor Pattern Send PatternNetwork PVC Tests/Data Port PVC Tests Isdn Call/PVC TestsTest Call ConnectivityPhysical Tests Screen Example Physical TestsLLB Line LoopbackMain Menu → Test→ Network Physical Tests PLB Payload LoopbackRLB AIS Repeater LoopbackMain Menu → Test→ Data Port Physical Tests DTE LoopbackDSX Dtlb DTESend Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line LoopbackQrss Send and Monitor Pattern TestsPing Screen Example IP Ping TestTarget IP Address Ping Options 1Ping Options 2 Inter-Ping DelaySource IP Address Packet SizePing Responses Field Possible Values Description Response TimeoutPing Options 3 Main Menu → Test→ IP Ping IP Ping Test ProcedureMain Menu → Test→ Lamp Test Lamp TestHis chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM SystemSetting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set ActivationsActivation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation CertificateScheduling Activations Checking the Status of Scheduled Activations Canceling Scheduled ActivationsAccessing and Printing the Certificate Summary Report 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver DevicesPreparation Alarms10-2 Properties10-3 Configuring NetScout Manager Plus10-4 10-5 Verifying Domains and Groups10-6 Correcting Domains and Groups10-7 Property Description Setting10-8 Adding SLV Alarms Using a Template10-9 Editing Alarms10-10 10-11 Adding SLV Alarms ManuallyParadyne 10-12Field Select or Enter 10-13 Creating History FilesChange 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-14Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Installing the User-Defined History FilesDvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-1510-16 Monitoring a DLCI’s History Data10-17 10-18 Monitoring the Agent Using NetScout Manager Plus10-19 Traffic Statistics Protocol Statistics Statistical Windows Supported10-20 11-1 Setting Up Network Health for FrameSaver Devices11-2 Installation and Setup of Network Health11-3 Discovering FrameSaver Elements11-4 Configuring the Discovered Elements11-5 Grouping Elements for ReportsGenerating Reports for a Group About Service Level ReportsAbout At-a-Glance Reports 11-6About Trend Reports Reports Applicable to SLV DevicesPrinted Reports 11-711-8 FrameSaver SLV Plus At-a-Glance Report 11-911-10 Menus Menu HierarchyStatus Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB SupportInterfaces Group mib-2 System Group mib-2FrameSaver Unit’s sysDescr system FrameSaver Unit’s sysObjectID systemFrame Relay Logical Layer Profile Link Name NAMFR DTE T1 FR NAM FR Service T1 FR NAMNetScout Indexes to the Interface Table ifTable IfName of the interface Rmon Logical LayerNumber Dlci number ALL Number Dlci number DTEExamples Standards Compliance for Snmp TrapsTrap warmStart Trap authenticationFailureTable B-3. warmStart Trap What It Indicates Possible Cause Variable-BindingTraps linkUp and linkDown PRI Physical SublayerMIB StringsLogical Link Sublayer BRIXxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific‘Path xxx.xxx.xxx.xxx Up Nnnn ’That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControlEvent Defaults Rmon Alarm and Event DefaultsEventIndex EventDescription EventType EventCommunity Dial Control Extension MIBRising Event Operation Physical Interface Alarm DefaultsFrame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne AreaDlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.10.32.2.1 6.1.2.1.2.2.16.1.2.1.16.12.2.1 MIB Rmon II RFC6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2Dlci CIR CIRDlci EIR 6.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.16.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Convention Meaning CLI CommandsX.x XxxxxxxxxxxxRouter CLI Commands, Codes, and Designations Access Control Commands Pager CommandTable C-1. Pager Command Table C-2. Access Control CommandsTable C-3. Configuration Commands Configuration CommandsConfigure terminal factory Example configure terminalTable C-4. Interface Commands 1 Interface CommandsCommand Mode config, config-if, config-subif Example interface serial 132.53.4.2Encapsulation encapsulation-type encapsulation-protocol Table C-4. Interface Commands 2Example ip address 132.53.4.2 Example encapsulation frame-relay ietfNo ip unnumbered null Table C-4. Interface Commands 3No frame-relay interface-dlci dlci-num Example ip unnumberedTable C-5. IP Routing Commands IP Routing CommandsNo ip routing No ip multicast-routingExample bridge crb 1 route ip Bridge CommandsTable C-6. Bridge Commands 1 Command Mode config-if, config-subif Table C-6. Bridge Commands 2No bridge-group bridge-group Example no bridge-groupTable C-7. ARP Commands ARP CommandsArp timeout time No arp timeout time Example arp timeoutTable C-8. NAT Commands 1 NAT CommandsExample ip nat translation timeout No ip nat inside outsideIp nat pool pool-name start-ip-addr end-ip-addr Table C-8. NAT Commands 2Netmask netmask prefix-length / prefix-length No ip nat pool pool-namestart-ip-addr end-ip-addrFrom previous Table C-8. NAT Commands 3Clear ip nat translation Table C-9. Dhcp Server Commands 1 Dhcp Server CommandsNo service dhcp No ip dhcp pool pool-nameDefault-router ip-address No default-router ip-address Table C-9. Dhcp Server Commands 2Domain-name domain-name No domain-name domain-name Dns-server ip-address No dns-server ip-addressNetwork network-num Table C-9. Dhcp Server Commands 3Table C-10. Dhcp Relay Agent Commands Dhcp Relay Agent CommandsNo ip dhcp-server ip-address Example ip dhcp relay max-clientsTable C-11. Filter Commands 1 Filter access-list CommandsAccess-list access-list-num permit deny No access-list access-list-numpermit denyFor Extended IP Access Lists Table C-11. Filter Commands 2Example access-list 200 permit 0x200 range Table C-11. Filter Commands 3For Protocol Type Access Lists No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4Table C-12. Diagnostic Commands 1 Diagnostic CommandsTraceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2Table C-13. Show Commands 1 Show CommandsShow configuration Show arpShow configuration saved unsaved Table C-13. Show Commands 2Show frame-relay map Show interface intf-type intf-num .sub-intf-numShow ip dhcp binding ip-address Table C-13. Show Commands 3Show ip nat translations Show ip route ip-addressShow spanning-tree Table C-13. Show Commands 4Show ip traffic Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type CodesTable C-14. Ethernet Type Codes Hex 2 Description All 3 n = Destination unreachable Protocol and Port DesignationsIcmp Designations All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries ShortcutsIntf-type intf-num .sub-intf-num Show Command SummaryTable D-1. Show Commands Function Table D-2. Access Control and System Level Commands Function Access Control and System Level Command SummaryTable D-3. CLI Commands 1 CLI Command SummaryClear counters intf-type intf-num .sub-intf-num Dns-serverip-addressEncapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2CLI Command Default Settings Rear Panels Connectors, Cables, and Pin AssignmentsConnectors, Cables, and Pin Assignments Model Signal Direction Pin # COM Port ConnectorPin # Signal Direction COM Port for 9126 and 9128-II 25-PositionCOM Port for 9128-II Carrier Mount COM Port-to-PC Cable Feature No -F2-550COM Port Non-Keyed Position Modular Plug DB9 SocketPosition Modular Plug DB25 Plug COM Port-to-Terminal/Printer Cable Feature No -F2-540COM Port Non-Keyed COM Port AUX Port Signal DB25 Pin # Direction COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port-to-Router Cables Cisco 2500 Series Router RJ45 Jack3COM Router DB9 Socket COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #COM Port AUX Port Signal RJ45 Pin # Direction COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # LAN Adapter Converter and Cable Gender Adapter/ChangerPlug-to-Modular Jack Converter Com Port Position DB25 Plug DTR RTSDirection Pin Socket DTE Port ConnectorStandard V.35 Crossover Cable Standard V.35 Straight-through CableMM NN PinDSX-1 Adapter Feature No -F1-560 DSX-1 ConnectorFunction Circuit Direction Pin Number Position DB15 Modular Plug Socket UnkeyedDSX-1 Port for 1-Slot 9128-II 15-Position Function Circuit Line # Pin # T1 Network Cable Feature No -F1-500T1 Mass Termination Cable Feature No -F1-500 Plug Unkeyed Ethernet Port ConnectorCanadian T1 Line Interface Cable Feature No -F1-510 Isdn Modular Cable Modem ConnectorIsdn DBM Connector Connectors, Cables, and Pin Assignments September Physical Dimensions Table F-1. NAM Technical Specifications 1 CriteriaApprovals Physical EnvironmentTable F-1. NAM Technical Specifications 2 Criteria Isdn PRI DBM Interface Table F-1. NAM Technical Specifications 3 CriteriaB8ZS Ethernet PortPower Consumption Dissipation Ethernet Port FrameSaver Isdn BRI DBM InterfaceBRI, NI-1 Heat Dissipation Max AC Power RequirementsTypical Power Consumption Service Supported Switch CompatibilitySwitched Network Interface Standards ComplianceLine Build-Out LBO Framing FormatCoding Format Equipment Model/FeatureDescription Number FrameSaver SLV UnitsEquipment List Isdn PRI DBM Optional Features FrameSaver SLM Feature Set UpgradePower Supplies NMS ProductsSeries Access Carrier 9128-II NAM only Cables Description Part Number Feature NumberIN-1 IndexCLI IN-2Becn Dhcp IN-3DBM IN-4EIR IN-5EER IN-6 IP SLV IN-7LAN LOS IN-8LOF NMS IN-9OID IN-10Port IN-11IN-12 IN-13 IN-14 IN-15 IN-16

Related manuals

Manual 32 pages 12.58 Kb