Paradyne 9126-II, CSU, DSU, 9128-II manual 101, Modem Port Options 2

Page 145

4. Configuration Options

Table 4-25. Modem Port Options (2 of 4)

Login Required

Possible Settings: Enable, Disable

Default Setting: Disable

Determines whether a user ID and password (referred to as the login) is required in order to log on to the asynchronous terminal connected to the modem port.

Display Conditions – This option only appears when Port Use is set to Terminal.

Enable – Requires a login to access the menu-driven user interface.

Disable – Does not require a login.

Port Access Level

Possible Settings: Level-1, Level-2, Level-3

Default Setting: Level-1

Specifies the level of user access privilege for an asynchronous terminal connected to the modem port.

NOTE: The effective access level is always the lowest one assigned to either the port or the user. For example, if the Port Access Level assigned is Level-2, but the User Access Level is Level-3, then only Level-3 access will be permitted for the modem port.

Display Conditions – This option only appears when Port Use is set to Terminal.

Level-1– Allows full access and control of the device including monitoring, diagnostics, and configuration. The user can add, change, and display configuration options, save, and perform device testing. If Login Required is set to Enable, the effective access level is determined by the user’s access level. Otherwise, the access level is 1.

CAUTION: Before changing the modem port’s access level to Level-2 or 3, make sure that either Telnet Session Access Level or the communications port’s Port Access Level is set to Level-1 and at least one Login ID are set to Level-1. Otherwise, access will be lost. If this occurs, you must reset the unit to the factory defaults and begin the configuration process again.

Level-2– Allows limited access and control of the device. The user can monitor and perform diagnostics, display status and configuration option information. If Login Required is set to Enable, the effective access level is 2 for User ID access levels of 1 or 2. User IDs set to access Level-3 have only Level-3 access.

Level-3– Allows limited access with monitoring control only. The user can only display and monitor status and configuration screens. If Login Required is set to Enable, the effective access level is 3 for all user IDs.

Inactivity Timeout

Possible Settings: Enable, Disable

Default Setting: Enable

Determines whether a user session is disconnected after a specified time of inactivity (no keyboard activity).

Display Conditions – This option only appears when Port Use is set to Terminal.

Enable – Disconnects the user session after the specified time of inactivity.

Disable – Does not disconnect the user session.

9128-A2-GB20-80

September 2002

4-101

Page 144 Page 146
Image 145
Page 144 Page 146
Contents FrameSaver SLV Copyright 2002 Paradyne Corporation All rights reserved Warranty, Sales, Service, and Training InformationDocument Feedback TrademarksContents Configuration Options ConfigurationTProceduresSeptember Iii Configuring the FrameSaver SLV RouterOperation and Maintenance Security and LoginsTroubleshooting Lamp Test Setting Up Network Health for FrameSaver Devices Setting Up NetScout Manager Plus for FrameSaver DevicesMenu HierarchyT ViiRouter CLI TCommands, Codes, and Designations Snmp MIBs and Traps, and Rmon Alarm DefaultsViii Connectors, Cables, and Pin Assignments Router Command Line Summaries and ShortcutsIndex Technical Specifications Equipment ListDocument Organization Purpose and Intended AudienceSection Description Section Description XiiXiii Product-Related DocumentsDocument Number Document Title Xiv Conventions UsedSystem Overview About the FrameSaver SLVRouter-Specific Features CSU/DSU-Specific FeaturesAbout the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Maximum Number of PVCs and Management PVCs Supported FrameSaver SLV Feature RouterThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II FeaturesFrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On ProcedureIf your login was Hen Select Main MenuScreen Format Description Screen Work AreasKeyboard Keys Navigating the ScreensPress For the screen Select Function Press Enter to Function KeysSelecting from a Menu Switching Between Screen AreasSelecting a Field Screen ContentsEntering Information CLI Keyboard Keys Navigating the Router’s CLIBasic Configuration Configuration ProceduresIsdn Configuration MenuConfiguration Option Area Description Configuration Option AreasMain Menu → Configuration Accessing and Displaying Configuration OptionsConfiguration → PVC Connections Changing Configuration OptionsSaving Configuration Options Configuration Options Configuration Options Main Menu → Easy Install Using the Easy Install FeatureEasy Install Screen Example Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUsMain Menu → Control→ System Information Entering System Information and Setting the System ClockIf the selection is Enter Setting Up Call Directories for Trap Dial-Out Setting Up the ModemMain Menu → Control→ Modem Call Directories Valid characters include ForSetting Up to Use the Modem PassThru Feature Main Menu → Auto-Configuration Setting Up Auto-ConfigurationAuto-Configuration Screen Example Main Menu → Auto-Configuration→Frame Relay Discovery Mode Selecting a Frame Relay Discovery ModeDiscovery Mode Configuration Description Only applies to models withDiscovery Mode Configuration Description Automatically Removing a Circuit Setting Up the DBM Physical Interface Setting Up Dial BackupMain Menu → Configuration → Isdn → Physical If you select Then Setting Up Automatic Backup ConfigurationFollowing prompt When Appears If you select Destinations Remove AlternateFrom PVCs Delete unusedFor Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Isdn → Link ProfilesModifying Isdn Link Profiles Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup TimersAssigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp TrapsSetting Up Back-to-Back Operation PVC Backup Over the Network InterfaceChanging Operating Mode Main Menu → Control→ Change Operating ModeConfiguration Option Tables Configuring Frame Relay and LMI for the System CSU/DSUs Configuring the Overall SystemMain Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 1System Frame Relay and LMI Options 2 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsClass of Svc Name Class of Service DefinitionsMeasure Latency & Availability Code Points AssignedCode Point Definitions Code Point DefinitionsCode Pnt NameService Level Verification Options 1 Configuring Service Level Verification OptionsSLV Type Available Settings Standard, COS 1-COS SLV Sample Interval secsDlci Down on SLV Timeout Service Level Verification Options 2SLV Timeout Error Event Threshold SLV Timeout Clearing Event ThresholdSLV Latency Clearing Event Threshold Service Level Verification Options 3SLV Packet Size bytes Main Menu → Configuration → System→ General Configuring General System OptionsTest Timeout General System Options 1General System Options 2 General System Options 3 System Alarm RelayConfiguring the Network Interface Configuring Physical InterfacesMain Menu → Configuration → Network→ Physical Network Physical Interface Options 1Network Physical Interface Options 2 Line Build Out LBO Possible Settings 0.0, -7.5, -15Bit Stuffing Transmit TimingNetwork Physical Interface Options 3 Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Initiated PLB Ansi Performance Report MessagesCircuit Identifier Network Physical Interface Options 4Main Menu → Configuration → Data Ports→ Physical Configuring a User Data Port CSU/DSUsPort Use Possible Settings Frame Relay, Synchronous Data Data Port Physical Interface Options 1Max Port Rate Kbps Data Port Physical Interface Options 2Port Base Rate Kbps Transmit Clock SourceMonitor RTS Control Data Port Physical Interface Options 3Monitor DTR Port DTE Initiated Loopbacks Data Port Physical Interface Options 4Invert Transmit and Receive Data Data Port Physical Interface Options 5 Action on Network Yellow AlarmMain Menu → Configuration → DSX-1 Configuring the DSX-1 InterfaceDSX-1 Physical Interface Options 1 Interface StatusSend All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2Service Profile ID Spid 1 or Configuring the Isdn DBM InterfaceIsdn BRI DBM Physical Interface Options Local Phone Number 1 or10. Isdn PRI DBM Physical Interface Options 1 Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESSLocal Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Main Menu → Configuration → Isdn → Isdn Link Profiles Setting Up Isdn Link Profiles11. Isdn Link Profile Options 1 Link NameOutbound Phone Number 11. Isdn Link Profile Options 2Inbound Calling ID 1 or Maximum Link Rate Kbps11. Isdn Link Profile Options 3 Assigning Time Slots/Cross ConnectionsCaller Identification Method Alternate Outbound Phone NumberFrame Relay Network Time Slot Assignment Screen Example Assigning Frame Relay Time Slots to the Network InterfaceValue Meaning Time Slot Assignment Rule Assigning DSX-1 Time Slots to the Network InterfaceNtt Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen ExampleDSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen ExamplePhysical Interface Options Clearing Assignments13. Interface Frame Relay Options 1 Configuring Frame Relay for an InterfaceLMI Traffic Policing 13. Interface Frame Relay Options 2LMI Parameters Frame Relay DS0s Base Rate13. Interface Frame Relay Options 3 14. Dlci Record Options 1 Manually Configuring Dlci RecordsDlci Number CIR bps 14. Dlci Record Options 2Committed Burst Size Bc Bits Excess Burst Size Bits 14. Dlci Record Options 3Dlci Priority Outbound Management Priority14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, NoneMain Menu → Configuration → PVC Connections Configuring PVC Connections15. PVC Connection Options 1 Source DlciSource Edlci 15. PVC Connection Options 2Primary Destination Link Primary Destination DlciPrimary Destination Edlci 15. PVC Connection Options 3Alternate Destination Link Alternate Destination DlciAlternate Destination Edlci 15. PVC Connection Options 4Main Menu → Configuration → IP Path List Static Configuring the IP Path List16. IP Path List Enter IP Address press ESC to abort ... FWD NoSetting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information17. Node IP Options 2 TS Access Management LinkTS Management Snmp Validation 17. Node IP Options 318. Management PVC Options 1 Configuring Management PVCsPayload Managed 18. Management PVC Options 2Set DE Primary Dlci 18. Management PVC Options 3Primary Edlci 18. Management PVC Options 4Alternate Dlci 18. Management PVC Options 5Alternate Edlci Encapsulation 18. Management PVC Options 6Name 1 Access Configuring General Snmp Management19. General Snmp Management Options 1 Snmp ManagementName 2 Access Configuring Telnet and/or FTP Session Support19. General Snmp Management Options 2 20. Telnet and FTP Session Options 1 Telnet Login RequiredTelnet Session 20. Telnet and FTP Session Options 2 21. Snmp NMS Security Options 1 Configuring Snmp NMS SecurityNMS IP Validation Number of Managers21. Snmp NMS Security Options 2 Configuring Snmp Traps and Trap Dial-Out22. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 22. Snmp Traps and Trap Dial-Out Options 3 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps 22. Snmp Traps and Trap Dial-Out Options 4 Possible Settings Network, Ports, DBM, All, NoneDlci Traps on Interfaces Filter Selection Field Rmon Traps22. Snmp Traps and Trap Dial-Out Options 5 Dial-Out Delay TIme MinTrap Dial-Out Trap DisconnectAlternate Dial-Out Directory 22. Snmp Traps and Trap Dial-Out Options 6Latency Traps IP SLV Availability Traps23. Ethernet Management Options 1 Configuring Ethernet ManagementProxy ARP 23. Ethernet Management Options 224. Communication Port Options 1 Configuring the Communication PortCharacter Length 24. Communication Port Options 2 Login RequiredParity Stop Bits24. Communication Port Options 3 RIP 24. Communication Port Options 4100 Configuring the Modem Port24. Communication Port Options 5 25. Modem Port Options 125. Modem Port Options 2 10125. Modem Port Options 3 10225. Modem Port Options 4 103Main Menu → Configuration → Auto Backup Criteria Configuring the Criteria for Automatic Backup26. Auto Backup Criteria Options 1 104When Auto Backup Allowed 26. Auto Backup Criteria Options 2Backup Allowed Day From nnnn Backup Allowed Day To nnnn106 Configuring the FrameSaver SLV Router Network Interface FrameSaver SLV Router OverviewEthernet IP Routing Address Resolution ProtocolProxy ARP Interface Configuration IP Options Processing Network Address TranslationApplications Supported by NAT NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration ExampleSave exit Network Address Port Translation Napt Configuration ExampleNapt Mapping Public IP Address Private IP Addresses Ip nat inside source list 1 interface se 0.x overload Access-list 1 permit 10.1.3.0Int ethernet 0 ip nat inside int serial 0.x ip nat outside Ip nat inside source static 10.1.1.1 NAT and Napt Configuration ExampleDynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration ExampleDhcp Relay Agent Dhcp Server at Remote Site Configuration ExampleIP Router Filtering Router SecurityBridge Filtering IP Filtering Provisioning the Router InterfaceLand Bug Prevention Smurf Attack PreventionConfiguring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting AccessSet the configuration option Limiting Dial-In Access via the Modem Port Disabling Isdn Access Controlling Isdn AccessIsdn Call Security Limiting Telnet Access Controlling Telnet or FTP AccessLimiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp AccessAssigning Snmp Community Names and Access Levels Main Menu → Configuration → Limiting Snmp Access Through IP AddressesGeneral Snmp Management → Snmp Management Enable Management and Communication →Main Menu → Control→ Administer Logins Creating a LoginField Enter Deleting a Login Modifying a LoginAccess Levels Command Modes Controlling Router CLI AccessLargo Enable Changing Access LevelsEnable password password EndSecurity and Logins September Operation and Maintenance Operation and Maintenance Main Menu → Status → Identity Displaying System InformationView this field To find Isdn DBM Viewing LEDs and Control LeadsFrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLVDisplay LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control LeadsMain Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control LeadsGeneral Status LEDs 1 LED DescriptionsLabel Indiction Color What It Means ALMContd General Status LEDs 2Model 9128-IILabel Indication Color What It Means Network, DSX, or PRI Interface LEDsUser Data Port LED CSU/DSUs Only Ethernet Port LED Routers OnlyAdditional Control Leads Label Indication What It Means Control Lead DescriptionsNetwork Interface User Data PortDevice Messages 1 What It Indicates What To Do Device MessagesSeen at an FTP TerminalSee Changing Software on Device Messages 2 What It Indicates What To DoPVC Device Messages 3 What It Indicates What To DoDevice Messages 4 What It Indicates What To Do Device Messages 5 What It Indicates What To Do Reset COM Port usageFrameSaver SLV II onlyDevice Messages 6 What It Indicates What To Do Status Menu Example Status InformationSystem and Test Status Messages Last System Reset Date and TimeMain Menu → Status → System and Test Status Self-Test Results MessagesHealth and Status Messages Change Operating ModeHealth and Status Messages 1 What It Indicates Isdn PRI DBM onlyFrame relay link 1,2 Health and Status Messages 2 What It IndicatesFrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It IndicatesHealth and Status Messages 5 What It Indicates Series Access Carrier onlyPathIP Address Down Nnnn, framerelaylink 1,2Health and Status Messages 6 What It Indicates Health and Status Messages 7 What It Indicates Configuration→ Time Slot Assignment → FrameRelay Network Assignments and an LMI failure is Test Status Messages 1 What It Indicates Test Status MessagesDclb Active, framerelaylink 1 or Framerelaylink 1 ,3Test Status Messages 2 What It Indicates Main Menu → Status→ LMI Reported DLCIs Network LMI-Reported DLCIs StatusLMI-Reported DLCIs Status Screen Example Tframe relay network, or Main Menu → Status→ IP Path Connection Status IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates Main Menu → Status→ PVC Connection Status PVC Connection StatusPVC Connection Status Screen Example MgmtPVCName 12. PVC Connection Status 1 Field What It IndicatesEdlci Status What It Indicates 12. PVC Connection Status 2 FieldDisplaying Network Time Slot Assignments Time Slot Assignment StatusMain Menu → Status→ Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen ExampleDisplaying DSX-1 Time Slot Assignments Cross Connect Status Field bottom IndicatesMain Menu → Status→ Timeslot Assignment Status→ DSX-1 DSX-1 Timeslot Assignment Status Screen ExampleMain Menu → Status→ DBM Interface Status DBM Interface StatusDBM Interface Status Screen Example Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It Indicates13. DBM Interface Status 2 Field What It Indicates Link Name DisabledAwarded and Being Delivered In Est Chnl-7Value is Call Awarded 13. DBM Interface Status 3 Field What It IndicatesBeing Delivered In Est Chnl-7Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance Main Menu → Status→ IP Routing Table IP Routing TableIP Routing Table Screen Example 15. IP Routing Table Values 1 Column What It IndicatesTTL 15. IP Routing Table Values 2 Column What It IndicatesMain Menu → Status→ Performance Statistics Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance StatisticsVerification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration OptionsSize is changed, a new average is not available until a new Main Menu → Status → Performance Statistics→ Dlci Dlci Performance Statistics18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci Main Menu → Status → Performance Statistics→ Frame Relay Frame Relay Performance StatisticsFor FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 1 What It Indicates20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay ErrorsFrame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc ErrorsMain Menu → Status → Performance Statistics→ ESF Line ESF Line Performance StatisticsTo select intervals You must enter an interval or time on Lofc ESF Line Performance Statistics Screen ExampleLofc UAS22. DBM Call Performance Statistics What It Indicates DBM Call Performance StatisticsMain Menu → Status → Performance Statistics → Ethernet Ethernet Performance Statistics23. Ethernet Performance Statistics What It Indicates Main Menu → Status → Trap Event Log Trap Event LogTrap Event Log Screen Example Canceling Modem PassThru Operation Activating the Modem PassThru FeatureMain Menu → Control→ Enable Modem PassThru to COM Main Menu → Control→ Disable Modem PassThru to COMVerifying Modem Operation Manually Disconnecting the ModemMain Menu → Control→ Disconnect Modem Isdn DBM Operation Forcing Backup DisruptiveMain Menu→ Test→ Isdn Call/PVC Tests Placing a Test Call NondisruptiveIf the Result is Then Verifying Isdn Lines Verifying That Backup Can Take PlaceSystem Operational should appear FTP File Transfers Command Definition If the message displayed is Then Upgrading System SoftwareMain Menu → Status→ Identity Upgrading Isdn BRI DBM SoftwareChanging Software Determining Whether a Download Is CompletedMain Menu → Control→ Select Software Release If retrieving Hen Transferring Collected DataMain Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm RelayOperation and Maintenance September Troubleshooting Indicators See Problem IndicatorsOperation and Maintenance Main Menu → Status → Display LEDs and Control LEDsResetting the Unit from the Control Menu Resetting the Unit and Restoring CommunicationResetting the Unit By Cycling the Power If selecting He following occurs Restoring Communication with an Improperly Configured UnitLMI Packet Capture Utility Feature Troubleshooting Management Link FeatureLMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace LogAlarm Conditions 1 What It Indicates What To Do AlarmsMenu → Control → Reset Device Main Menu → Configuration → Isdn → Link Profiles Alarm Conditions 2 What It Indicates What To DoName IPAddressMenu→ Configuration→ Alarm Conditions 3 What It Indicates What To DoLMI Down, frame relay LinkDTE Alarm Conditions 4 What It Indicates What To DoPathIP Address Alarm Conditions 5 What It Indicates What To DoNnnn , frame relay Alarm Conditions 6 What It Indicates What To DoAlarm Conditions 7 What It Indicates What To Do Device Problems Troubleshooting TablesDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event LogImproperly Configured Unit on Device Problems 2 Symptom Possible Cause SolutionsFrame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC ProblemsIsdn DBM Problems Symptom Possible Cause Solutions Isdn DBM ProblemsMain Menu → Status → DBM Interface Status Test Menu Example Tests AvailableDBM Tests Test Timeout FeatureStarting and Stopping a Test When the status of a test is Only command available isAborting All Tests PVC Tests Screen Example PVC TestsMain Menu → Test→ Network PVC Test PVC LoopbackMain Menu → Test→ Data Port PVC Tests Main Menu → Test→ Isdn Call/PVC TestsMonitor Pattern Send PatternNetwork PVC Tests/Data Port PVC Tests Isdn Call/PVC TestsTest Call ConnectivityPhysical Tests Screen Example Physical TestsMain Menu → Test→ Network Physical Tests Line LoopbackLLB PLB Payload LoopbackRLB AIS Repeater LoopbackMain Menu → Test→ Data Port Physical Tests DTE LoopbackDSX Dtlb DTESend Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line LoopbackQrss Send and Monitor Pattern TestsPing Screen Example IP Ping TestTarget IP Address Ping Options 1Ping Options 2 Inter-Ping DelaySource IP Address Packet SizePing Options 3 Response TimeoutPing Responses Field Possible Values Description Main Menu → Test→ IP Ping IP Ping Test ProcedureMain Menu → Test→ Lamp Test Lamp TestHis chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM SystemSetting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set ActivationsActivation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation CertificateScheduling Activations Accessing and Printing the Certificate Summary Report Canceling Scheduled ActivationsChecking the Status of Scheduled Activations 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver DevicesPreparation Alarms10-2 Properties10-3 Configuring NetScout Manager Plus10-4 10-5 Verifying Domains and Groups10-6 Correcting Domains and Groups10-7 Property Description Setting10-8 Adding SLV Alarms Using a Template10-9 Editing Alarms10-10 10-11 Adding SLV Alarms ManuallyField Select or Enter 10-12Paradyne 10-13 Creating History FilesChange 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-14Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Installing the User-Defined History FilesDvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-1510-16 Monitoring a DLCI’s History Data10-17 10-18 Monitoring the Agent Using NetScout Manager Plus10-19 10-20 Statistical Windows SupportedTraffic Statistics Protocol Statistics 11-1 Setting Up Network Health for FrameSaver Devices11-2 Installation and Setup of Network Health11-3 Discovering FrameSaver Elements11-4 Configuring the Discovered Elements11-5 Grouping Elements for ReportsGenerating Reports for a Group About Service Level ReportsAbout At-a-Glance Reports 11-6About Trend Reports Reports Applicable to SLV DevicesPrinted Reports 11-711-8 FrameSaver SLV Plus At-a-Glance Report 11-911-10 Menus Menu HierarchyStatus Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB SupportInterfaces Group mib-2 System Group mib-2FrameSaver Unit’s sysDescr system FrameSaver Unit’s sysObjectID systemFrame Relay Logical Layer Profile Link Name NAMNetScout Indexes to the Interface Table ifTable FR Service T1 FR NAMFR DTE T1 FR NAM IfName of the interface Rmon Logical LayerNumber Dlci number ALL Number Dlci number DTEExamples Standards Compliance for Snmp TrapsTrap warmStart Trap authenticationFailureTable B-3. warmStart Trap What It Indicates Possible Cause Variable-BindingTraps linkUp and linkDown PRI Physical SublayerMIB StringsLogical Link Sublayer BRIXxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific‘Path xxx.xxx.xxx.xxx Up Nnnn ’That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControlEvent Defaults Rmon Alarm and Event DefaultsEventIndex EventDescription EventType EventCommunity Dial Control Extension MIBRising Event Operation Physical Interface Alarm DefaultsFrame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne AreaDlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.10.32.2.1 6.1.2.1.2.2.16.1.2.1.16.12.2.1 MIB Rmon II RFC6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2Dlci CIR CIRDlci EIR 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.16.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Convention Meaning CLI CommandsX.x XxxxxxxxxxxxRouter CLI Commands, Codes, and Designations Access Control Commands Pager CommandTable C-1. Pager Command Table C-2. Access Control CommandsTable C-3. Configuration Commands Configuration CommandsConfigure terminal factory Example configure terminalTable C-4. Interface Commands 1 Interface CommandsCommand Mode config, config-if, config-subif Example interface serial 132.53.4.2Encapsulation encapsulation-type encapsulation-protocol Table C-4. Interface Commands 2Example ip address 132.53.4.2 Example encapsulation frame-relay ietfNo ip unnumbered null Table C-4. Interface Commands 3No frame-relay interface-dlci dlci-num Example ip unnumberedTable C-5. IP Routing Commands IP Routing CommandsNo ip routing No ip multicast-routingTable C-6. Bridge Commands 1 Bridge CommandsExample bridge crb 1 route ip Command Mode config-if, config-subif Table C-6. Bridge Commands 2No bridge-group bridge-group Example no bridge-groupTable C-7. ARP Commands ARP CommandsArp timeout time No arp timeout time Example arp timeoutTable C-8. NAT Commands 1 NAT CommandsExample ip nat translation timeout No ip nat inside outsideIp nat pool pool-name start-ip-addr end-ip-addr Table C-8. NAT Commands 2Netmask netmask prefix-length / prefix-length No ip nat pool pool-namestart-ip-addr end-ip-addrClear ip nat translation Table C-8. NAT Commands 3From previous Table C-9. Dhcp Server Commands 1 Dhcp Server CommandsNo service dhcp No ip dhcp pool pool-nameDefault-router ip-address No default-router ip-address Table C-9. Dhcp Server Commands 2Domain-name domain-name No domain-name domain-name Dns-server ip-address No dns-server ip-addressNetwork network-num Table C-9. Dhcp Server Commands 3Table C-10. Dhcp Relay Agent Commands Dhcp Relay Agent CommandsNo ip dhcp-server ip-address Example ip dhcp relay max-clientsTable C-11. Filter Commands 1 Filter access-list CommandsAccess-list access-list-num permit deny No access-list access-list-numpermit denyFor Extended IP Access Lists Table C-11. Filter Commands 2For Protocol Type Access Lists Table C-11. Filter Commands 3Example access-list 200 permit 0x200 range No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4Table C-12. Diagnostic Commands 1 Diagnostic CommandsTraceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2Table C-13. Show Commands 1 Show CommandsShow configuration Show arpShow configuration saved unsaved Table C-13. Show Commands 2Show frame-relay map Show interface intf-type intf-num .sub-intf-numShow ip dhcp binding ip-address Table C-13. Show Commands 3Show ip nat translations Show ip route ip-addressShow ip traffic Table C-13. Show Commands 4Show spanning-tree Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type CodesTable C-14. Ethernet Type Codes Hex 2 Description Icmp Designations Protocol and Port DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries ShortcutsTable D-1. Show Commands Function Show Command SummaryIntf-type intf-num .sub-intf-num Table D-2. Access Control and System Level Commands Function Access Control and System Level Command SummaryTable D-3. CLI Commands 1 CLI Command SummaryClear counters intf-type intf-num .sub-intf-num Dns-serverip-addressEncapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2CLI Command Default Settings Rear Panels Connectors, Cables, and Pin AssignmentsConnectors, Cables, and Pin Assignments Model Signal Direction Pin # COM Port ConnectorPin # Signal Direction COM Port for 9126 and 9128-II 25-PositionCOM Port for 9128-II Carrier Mount COM Port-to-PC Cable Feature No -F2-550COM Port Non-Keyed Position Modular Plug DB9 SocketCOM Port Non-Keyed COM Port-to-Terminal/Printer Cable Feature No -F2-540Position Modular Plug DB25 Plug COM Port AUX Port Signal DB25 Pin # Direction COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port-to-Router Cables Cisco 2500 Series Router RJ45 JackCOM Port AUX Port Signal RJ45 Pin # Direction COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # LAN Adapter Converter and Cable Gender Adapter/ChangerPlug-to-Modular Jack Converter Com Port Position DB25 Plug DTR RTSDirection Pin Socket DTE Port ConnectorStandard V.35 Crossover Cable Standard V.35 Straight-through CableMM NN PinDSX-1 Adapter Feature No -F1-560 DSX-1 ConnectorFunction Circuit Direction Pin Number Position DB15 Modular Plug Socket UnkeyedDSX-1 Port for 1-Slot 9128-II 15-Position T1 Mass Termination Cable Feature No -F1-500 T1 Network Cable Feature No -F1-500Function Circuit Line # Pin # Canadian T1 Line Interface Cable Feature No -F1-510 Ethernet Port ConnectorPlug Unkeyed Isdn DBM Connector Modem ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Physical Dimensions Table F-1. NAM Technical Specifications 1 CriteriaApprovals Physical EnvironmentTable F-1. NAM Technical Specifications 2 Criteria Isdn PRI DBM Interface Table F-1. NAM Technical Specifications 3 CriteriaB8ZS Ethernet PortPower Consumption Dissipation BRI, NI-1 Isdn BRI DBM InterfaceEthernet Port FrameSaver Typical Power Consumption AC Power RequirementsHeat Dissipation Max Service Supported Switch CompatibilitySwitched Network Interface Standards ComplianceCoding Format Framing FormatLine Build-Out LBO Equipment Model/FeatureDescription Number FrameSaver SLV UnitsEquipment List Isdn PRI DBM Optional Features FrameSaver SLM Feature Set UpgradePower Supplies NMS ProductsSeries Access Carrier 9128-II NAM only Cables Description Part Number Feature NumberIN-1 IndexBecn IN-2CLI Dhcp IN-3DBM IN-4EER IN-5EIR IN-6 LAN IN-7IP SLV LOF IN-8LOS NMS IN-9OID IN-10Port IN-11IN-12 IN-13 IN-14 IN-15 IN-16
Related manuals
Manual 32 pages 12.58 Kb
Top Page Image Contents