Paradyne CSU, DSU, 9126-II, 9128-II manual Management PVC Options 3, Primary Dlci

Page 123

4. Configuration Options

Table 4-18. Management PVC Options (3 of 6)

Primary Link

Possible Settings: Net1-FR1, Port-n, Rtr-S0, ISDN Link Name, Clear

Default Setting: Initially blank; no default.

Specifies the frame relay interface to use for this management PVC. The interface selected must have at least one DLCI (or DLCI with EDLCI) defined, which is not part of a PVC connection or already assigned as a management PVC.

Display Conditions – The Port-1 setting does not appear if the PVC is IP Enabled or Payload Managed is enabled.

Net1-FR1– Specifies the network interface as the source link for the connection.

Port-n– Specifies the frame relay link on the user data port as the destination link for the connection.

Rtr-S0 – For the FrameSaver SLV 9126-II Router, specifies that the vertual router port be used in the connection.

ISDN Link Name – For units with ISDN backup capability, specifies the ISDN link on the DBM to be used in the connection. This can be any nonnull link name configured on an ISDN frame relay link on an installed DBM.

Clear – Clears the link and the DLCI field, and suppresses the EDLCI field if the DLCI was multiplexed.

Primary DLCI

Possible Settings: 16 – 1007

Default Setting: Initially blank; no default.

Specifies the DLCI number used for the management PVC after the frame relay interface is selected.

The DLCI must be defined for the link (i.e., has a DLCI record), and it must not be part of a PVC connection or already assigned as a management PVC. For multiplexed DLCIs, at least one EDLCI must be unconfigured for the DLCI.

NOTES:

–DLCI cannot be entered if the Link field is blank.

–Clearing the Link also clears the DLCI.

–When an ISDN DBM is installed and the DLCI assigned to the PVC is in a Backup Group (see Table 4-14, DLCI Record Options), the letter designation assigned to the group of DLCIs appears next to the primary destination DLCI number on the Management PVCs Options screen.

16 – 1007 – Specifies the DLCI number (inclusive).

9128-A2-GB20-80

September 2002

4-79

Image 123

Contents FrameSaver SLV Trademarks Warranty, Sales, Service, and Training InformationCopyright 2002 Paradyne Corporation All rights reserved Document FeedbackContents ConfigurationTProcedures Configuration OptionsSeptember Iii Configuring the FrameSaver SLV RouterOperation and Maintenance Security and LoginsTroubleshooting Lamp Test Vii Setting Up NetScout Manager Plus for FrameSaver DevicesSetting Up Network Health for FrameSaver Devices Menu HierarchyTSnmp MIBs and Traps, and Rmon Alarm Defaults Router CLI TCommands, Codes, and DesignationsViii Connectors, Cables, and Pin Assignments Router Command Line Summaries and ShortcutsIndex Technical Specifications Equipment ListPurpose and Intended Audience Document OrganizationSection Description Section Description XiiProduct-Related Documents XiiiDocument Number Document Title Xiv Conventions UsedSystem Overview About the FrameSaver SLVRouter-Specific Features CSU/DSU-Specific FeaturesAbout the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set FrameSaver SLV Feature Router Maximum Number of PVCs and Management PVCs SupportedThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II FeaturesFrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On ProcedureIf your login was Hen Select Main MenuScreen Format Description Screen Work AreasNavigating the Screens Keyboard KeysPress For the screen Select Function Press Enter to Function KeysSelecting from a Menu Switching Between Screen AreasScreen Contents Selecting a FieldEntering Information CLI Keyboard Keys Navigating the Router’s CLIBasic Configuration Configuration ProceduresIsdn Configuration MenuConfiguration Option Area Description Configuration Option AreasMain Menu → Configuration Accessing and Displaying Configuration OptionsConfiguration → PVC Connections Changing Configuration OptionsSaving Configuration Options Configuration Options Configuration Options Using the Easy Install Feature Main Menu → Easy InstallEasy Install Screen Example Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUsEntering System Information and Setting the System Clock Main Menu → Control→ System InformationIf the selection is Enter Valid characters include For Setting Up the ModemSetting Up Call Directories for Trap Dial-Out Main Menu → Control→ Modem Call DirectoriesSetting Up to Use the Modem PassThru Feature Setting Up Auto-Configuration Main Menu → Auto-ConfigurationAuto-Configuration Screen Example Only applies to models with Selecting a Frame Relay Discovery ModeMain Menu → Auto-Configuration→Frame Relay Discovery Mode Discovery Mode Configuration DescriptionDiscovery Mode Configuration Description Automatically Removing a Circuit Setting Up Dial Backup Setting Up the DBM Physical InterfaceMain Menu → Configuration → Isdn → Physical If you select Then Setting Up Automatic Backup ConfigurationFollowing prompt When Appears If you select Delete unused Remove AlternateDestinations From PVCsMain Menu → Configuration → Isdn → Link Profiles For Originating a Backup Call For Answering a Backup CallModifying Isdn Link Profiles Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup TimersAssigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp TrapsMain Menu → Control→ Change Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Changing Operating ModeConfiguration Option Tables System Frame Relay and LMI Options 1 Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs Main Menu → Configuration → System → Frame Relay and LMISystem Frame Relay and LMI Options 2 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsCode Points Assigned Class of Service DefinitionsClass of Svc Name Measure Latency & AvailabilityName Code Point DefinitionsCode Point Definitions Code PntSLV Sample Interval secs Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Type Available Settings Standard, COS 1-COSSLV Timeout Clearing Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Error Event ThresholdService Level Verification Options 3 SLV Latency Clearing Event ThresholdSLV Packet Size bytes General System Options 1 Configuring General System OptionsMain Menu → Configuration → System→ General Test TimeoutGeneral System Options 2 General System Options 3 System Alarm RelayNetwork Physical Interface Options 1 Configuring Physical InterfacesConfiguring the Network Interface Main Menu → Configuration → Network→ PhysicalTransmit Timing Line Build Out LBO Possible Settings 0.0, -7.5, -15Network Physical Interface Options 2 Bit StuffingAnsi Performance Report Messages Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Physical Interface Options 3 Network Initiated PLBCircuit Identifier Network Physical Interface Options 4Data Port Physical Interface Options 1 Configuring a User Data Port CSU/DSUsMain Menu → Configuration → Data Ports→ Physical Port Use Possible Settings Frame Relay, Synchronous DataTransmit Clock Source Data Port Physical Interface Options 2Max Port Rate Kbps Port Base Rate KbpsData Port Physical Interface Options 3 Monitor RTS ControlMonitor DTR Data Port Physical Interface Options 4 Port DTE Initiated LoopbacksInvert Transmit and Receive Data Data Port Physical Interface Options 5 Action on Network Yellow AlarmInterface Status Configuring the DSX-1 InterfaceMain Menu → Configuration → DSX-1 DSX-1 Physical Interface Options 1Send All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2Local Phone Number 1 or Configuring the Isdn DBM InterfaceService Profile ID Spid 1 or Isdn BRI DBM Physical Interface OptionsSwitch Type Possible Settings NI-2, ATT4ESS, ATT5ESS 10. Isdn PRI DBM Physical Interface Options 1Local Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Link Name Setting Up Isdn Link ProfilesMain Menu → Configuration → Isdn → Isdn Link Profiles 11. Isdn Link Profile Options 1Maximum Link Rate Kbps 11. Isdn Link Profile Options 2Outbound Phone Number Inbound Calling ID 1 orAlternate Outbound Phone Number Assigning Time Slots/Cross Connections11. Isdn Link Profile Options 3 Caller Identification MethodAssigning Frame Relay Time Slots to the Network Interface Frame Relay Network Time Slot Assignment Screen ExampleValue Meaning Assigning DSX-1 Time Slots to the Network Interface Time Slot Assignment RuleNtt Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen ExampleDSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen ExamplePhysical Interface Options Clearing AssignmentsConfiguring Frame Relay for an Interface 13. Interface Frame Relay Options 1LMI Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 2Traffic Policing LMI Parameters13. Interface Frame Relay Options 3 Manually Configuring Dlci Records 14. Dlci Record Options 1Dlci Number 14. Dlci Record Options 2 CIR bpsCommitted Burst Size Bc Bits Outbound Management Priority 14. Dlci Record Options 3Excess Burst Size Bits Dlci Priority14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, NoneSource Dlci Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections 15. PVC Connection Options 1Primary Destination Dlci 15. PVC Connection Options 2Source Edlci Primary Destination LinkAlternate Destination Dlci 15. PVC Connection Options 3Primary Destination Edlci Alternate Destination LinkAlternate Destination Edlci 15. PVC Connection Options 4Enter IP Address press ESC to abort ... FWD No Configuring the IP Path ListMain Menu → Configuration → IP Path List Static 16. IP Path ListSetting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information17. Node IP Options 2 TS Access Management LinkTS Management Snmp Validation 17. Node IP Options 318. Management PVC Options 1 Configuring Management PVCs18. Management PVC Options 2 Payload ManagedSet DE Primary Dlci 18. Management PVC Options 3Primary Edlci 18. Management PVC Options 418. Management PVC Options 5 Alternate DlciAlternate Edlci Encapsulation 18. Management PVC Options 6Snmp Management Configuring General Snmp ManagementName 1 Access 19. General Snmp Management Options 1Configuring Telnet and/or FTP Session Support Name 2 Access19. General Snmp Management Options 2 Telnet Login Required 20. Telnet and FTP Session Options 1Telnet Session 20. Telnet and FTP Session Options 2 Number of Managers Configuring Snmp NMS Security21. Snmp NMS Security Options 1 NMS IP ValidationConfiguring Snmp Traps and Trap Dial-Out 21. Snmp NMS Security Options 222. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 Link Traps Possible Settings Disable, Up, Down, Both 22. Snmp Traps and Trap Dial-Out Options 3Enterprise Specific Traps Rmon Traps Possible Settings Network, Ports, DBM, All, None22. Snmp Traps and Trap Dial-Out Options 4 Dlci Traps on Interfaces Filter Selection FieldTrap Disconnect Dial-Out Delay TIme Min22. Snmp Traps and Trap Dial-Out Options 5 Trap Dial-OutIP SLV Availability Traps 22. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory Latency Traps23. Ethernet Management Options 1 Configuring Ethernet ManagementProxy ARP 23. Ethernet Management Options 2Configuring the Communication Port 24. Communication Port Options 1Character Length Stop Bits Login Required24. Communication Port Options 2 Parity24. Communication Port Options 3 RIP 24. Communication Port Options 425. Modem Port Options 1 Configuring the Modem Port100 24. Communication Port Options 525. Modem Port Options 2 10125. Modem Port Options 3 10225. Modem Port Options 4 103104 Configuring the Criteria for Automatic BackupMain Menu → Configuration → Auto Backup Criteria 26. Auto Backup Criteria Options 1Backup Allowed Day To nnnn 26. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day From nnnn106 Configuring the FrameSaver SLV Router FrameSaver SLV Router Overview Network InterfaceEthernet Address Resolution Protocol IP RoutingProxy ARP Interface Configuration Network Address Translation IP Options ProcessingApplications Supported by NAT NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration ExampleSave exit Napt Configuration Example Network Address Port TranslationNapt Mapping Public IP Address Private IP Addresses Access-list 1 permit 10.1.3.0 Ip nat inside source list 1 interface se 0.x overloadInt ethernet 0 ip nat inside int serial 0.x ip nat outside Ip nat inside source static 10.1.1.1 NAT and Napt Configuration ExampleDynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration ExampleDhcp Relay Agent Dhcp Server at Remote Site Configuration ExampleRouter Security IP Router FilteringBridge Filtering Smurf Attack Prevention Provisioning the Router InterfaceIP Filtering Land Bug PreventionConfiguring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting AccessSet the configuration option Limiting Dial-In Access via the Modem Port Controlling Isdn Access Disabling Isdn AccessIsdn Call Security Limiting Telnet Access Controlling Telnet or FTP AccessLimiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp AccessAssigning Snmp Community Names and Access Levels Management and Communication → Limiting Snmp Access Through IP AddressesMain Menu → Configuration → General Snmp Management → Snmp Management EnableCreating a Login Main Menu → Control→ Administer LoginsField Enter Deleting a Login Modifying a LoginControlling Router CLI Access Access Levels Command ModesLargo End Changing Access LevelsEnable Enable password passwordSecurity and Logins September Operation and Maintenance Operation and Maintenance Displaying System Information Main Menu → Status → IdentityView this field To find Isdn DBM Viewing LEDs and Control LeadsFrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLVDisplay LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control LeadsMain Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control LeadsALM LED DescriptionsGeneral Status LEDs 1 Label Indiction Color What It Means9128-II General Status LEDs 2Contd ModelEthernet Port LED Routers Only Network, DSX, or PRI Interface LEDsLabel Indication Color What It Means User Data Port LED CSU/DSUs OnlyUser Data Port Control Lead DescriptionsAdditional Control Leads Label Indication What It Means Network InterfaceTerminal Device MessagesDevice Messages 1 What It Indicates What To Do Seen at an FTPSee Changing Software on Device Messages 2 What It Indicates What To DoPVC Device Messages 3 What It Indicates What To DoDevice Messages 4 What It Indicates What To Do II only Reset COM Port usageDevice Messages 5 What It Indicates What To Do FrameSaver SLVDevice Messages 6 What It Indicates What To Do Status Menu Example Status InformationSelf-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Main Menu → Status → System and Test StatusIsdn PRI DBM only Change Operating ModeHealth and Status Messages Health and Status Messages 1 What It IndicatesHealth and Status Messages 2 What It Indicates Frame relay link 1,2FrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It IndicatesNnnn, framerelaylink 1,2 Series Access Carrier onlyHealth and Status Messages 5 What It Indicates PathIP Address DownHealth and Status Messages 6 What It Indicates Configuration→ Time Slot Assignment → Frame Health and Status Messages 7 What It IndicatesRelay Network Assignments and an LMI failure is Framerelaylink 1 ,3 Test Status MessagesTest Status Messages 1 What It Indicates Dclb Active, framerelaylink 1 orTest Status Messages 2 What It Indicates Network LMI-Reported DLCIs Status Main Menu → Status→ LMI Reported DLCIsLMI-Reported DLCIs Status Screen Example Tframe relay network, or IP Path Connection Status Main Menu → Status→ IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates PVC Connection Status Main Menu → Status→ PVC Connection StatusPVC Connection Status Screen Example 12. PVC Connection Status 1 Field What It Indicates MgmtPVCNameEdlci Status What It Indicates 12. PVC Connection Status 2 FieldNetwork Timeslot Assignment Status Screen Example Time Slot Assignment StatusDisplaying Network Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status → NetworkDSX-1 Timeslot Assignment Status Screen Example Cross Connect Status Field bottom IndicatesDisplaying DSX-1 Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status→ DSX-1DBM Interface Status Main Menu → Status→ DBM Interface StatusDBM Interface Status Screen Example Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It IndicatesDelivered In Est Chnl-7 Link Name Disabled13. DBM Interface Status 2 Field What It Indicates Awarded and BeingChnl-7 13. DBM Interface Status 3 Field What It IndicatesValue is Call Awarded Being Delivered In EstMost Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance 15. IP Routing Table Values 1 Column What It Indicates IP Routing TableMain Menu → Status→ IP Routing Table IP Routing Table Screen ExampleTTL 15. IP Routing Table Values 2 Column What It IndicatesPerformance Statistics Main Menu → Status→ Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance StatisticsVerification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration OptionsSize is changed, a new average is not available until a new Dlci Performance Statistics Main Menu → Status → Performance Statistics→ Dlci18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics→ Frame Relay For FrameSaver units with an Isdn DBM20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay ErrorsFrame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc ErrorsESF Line Performance Statistics Main Menu → Status → Performance Statistics→ ESF LineTo select intervals You must enter an interval or time on Lofc ESF Line Performance Statistics Screen ExampleLofc UAS22. DBM Call Performance Statistics What It Indicates DBM Call Performance StatisticsEthernet Performance Statistics Main Menu → Status → Performance Statistics → Ethernet23. Ethernet Performance Statistics What It Indicates Trap Event Log Main Menu → Status → Trap Event LogTrap Event Log Screen Example Main Menu → Control→ Disable Modem PassThru to COM Activating the Modem PassThru FeatureCanceling Modem PassThru Operation Main Menu → Control→ Enable Modem PassThru to COMManually Disconnecting the Modem Verifying Modem OperationMain Menu → Control→ Disconnect Modem Isdn DBM Operation Forcing Backup DisruptivePlacing a Test Call Nondisruptive Main Menu→ Test→ Isdn Call/PVC TestsIf the Result is Then Verifying That Backup Can Take Place Verifying Isdn LinesSystem Operational should appear FTP File Transfers Command Definition If the message displayed is Then Upgrading System SoftwareMain Menu → Status→ Identity Upgrading Isdn BRI DBM SoftwareDetermining Whether a Download Is Completed Changing SoftwareMain Menu → Control→ Select Software Release If retrieving Hen Transferring Collected DataMain Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm RelayOperation and Maintenance September Troubleshooting Main Menu → Status → Display LEDs and Control LEDs Problem IndicatorsIndicators See Operation and MaintenanceResetting the Unit and Restoring Communication Resetting the Unit from the Control MenuResetting the Unit By Cycling the Power If selecting He following occurs Restoring Communication with an Improperly Configured UnitLMI Packet Capture Utility Feature Troubleshooting Management Link FeatureLMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace LogAlarms Alarm Conditions 1 What It Indicates What To DoMenu → Control → Reset Device IPAddress Alarm Conditions 2 What It Indicates What To DoMain Menu → Configuration → Isdn → Link Profiles NameLink Alarm Conditions 3 What It Indicates What To DoMenu→ Configuration→ LMI Down, frame relayDTE Alarm Conditions 4 What It Indicates What To DoPathIP Address Alarm Conditions 5 What It Indicates What To DoNnnn , frame relay Alarm Conditions 6 What It Indicates What To DoAlarm Conditions 7 What It Indicates What To Do Viewing the Trap Event Log Troubleshooting TablesDevice Problems Device Problems 1 Symptom Possible Cause SolutionsImproperly Configured Unit on Device Problems 2 Symptom Possible Cause SolutionsFrame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC ProblemsIsdn DBM Problems Isdn DBM Problems Symptom Possible Cause SolutionsMain Menu → Status → DBM Interface Status Test Menu Example Tests AvailableDBM Tests Test Timeout FeatureStarting and Stopping a Test When the status of a test is Only command available isAborting All Tests PVC Tests Screen Example PVC TestsMain Menu → Test→ Isdn Call/PVC Tests PVC LoopbackMain Menu → Test→ Network PVC Test Main Menu → Test→ Data Port PVC TestsIsdn Call/PVC Tests Send PatternMonitor Pattern Network PVC Tests/Data Port PVC TestsTest Call ConnectivityPhysical Tests Screen Example Physical TestsLine Loopback Main Menu → Test→ Network Physical TestsLLB PLB Payload LoopbackRLB AIS Repeater LoopbackDtlb DTE DTE LoopbackMain Menu → Test→ Data Port Physical Tests DSXSend Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line LoopbackQrss Send and Monitor Pattern TestsPing Screen Example IP Ping TestTarget IP Address Ping Options 1Packet Size Inter-Ping DelayPing Options 2 Source IP AddressResponse Timeout Ping Options 3Ping Responses Field Possible Values Description Main Menu → Test→ IP Ping IP Ping Test ProcedureMain Menu → Test→ Lamp Test Lamp TestHis chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM SystemSetting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set ActivationsActivation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation CertificateScheduling Activations Canceling Scheduled Activations Accessing and Printing the Certificate Summary ReportChecking the Status of Scheduled Activations 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver DevicesProperties AlarmsPreparation 10-210-3 Configuring NetScout Manager Plus10-4 10-5 Verifying Domains and Groups10-6 Correcting Domains and Groups10-7 Property Description Setting10-8 Adding SLV Alarms Using a Template10-9 Editing Alarms10-10 10-11 Adding SLV Alarms Manually10-12 Field Select or EnterParadyne 10-13 Creating History FilesChange 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-1410-15 Installing the User-Defined History FilesDvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Dvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh10-16 Monitoring a DLCI’s History Data10-17 10-18 Monitoring the Agent Using NetScout Manager Plus10-19 Statistical Windows Supported 10-20Traffic Statistics Protocol Statistics 11-1 Setting Up Network Health for FrameSaver Devices11-2 Installation and Setup of Network Health11-3 Discovering FrameSaver Elements11-4 Configuring the Discovered Elements11-5 Grouping Elements for Reports11-6 About Service Level ReportsGenerating Reports for a Group About At-a-Glance Reports11-7 Reports Applicable to SLV DevicesAbout Trend Reports Printed Reports11-8 FrameSaver SLV Plus At-a-Glance Report 11-911-10 Menus Menu HierarchyStatus Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB SupportFrameSaver Unit’s sysObjectID system System Group mib-2Interfaces Group mib-2 FrameSaver Unit’s sysDescr systemFrame Relay Logical Layer Profile Link Name NAMFR Service T1 FR NAM NetScout Indexes to the Interface Table ifTableFR DTE T1 FR NAM Number Dlci number DTE Rmon Logical LayerIfName of the interface Number Dlci number ALLExamples Standards Compliance for Snmp TrapsVariable-Binding Trap authenticationFailureTrap warmStart Table B-3. warmStart Trap What It Indicates Possible CauseTraps linkUp and linkDown Strings Physical SublayerPRI MIBLogical Link Sublayer BRIXxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific‘Path xxx.xxx.xxx.xxx Up Nnnn ’That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControlDial Control Extension MIB Rmon Alarm and Event DefaultsEvent Defaults EventIndex EventDescription EventType EventCommunityRising Event Operation Physical Interface Alarm DefaultsFrame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne AreaDlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order MIB Rmon II RFC 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 6.1.2.1.16.12.2.1CIR 6.1.4.1.1795.2.24.26.1.4.1.1795.2.24.2.6.9.4 Dlci CIRDlci EIR 6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.16.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.16.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Xxxxxxxxxxxx CLI CommandsConvention Meaning X.xRouter CLI Commands, Codes, and Designations Table C-2. Access Control Commands Pager CommandAccess Control Commands Table C-1. Pager CommandExample configure terminal Configuration CommandsTable C-3. Configuration Commands Configure terminal factoryExample interface serial 132.53.4.2 Interface CommandsTable C-4. Interface Commands 1 Command Mode config, config-if, config-subifExample encapsulation frame-relay ietf Table C-4. Interface Commands 2Encapsulation encapsulation-type encapsulation-protocol Example ip address 132.53.4.2Example ip unnumbered Table C-4. Interface Commands 3No ip unnumbered null No frame-relay interface-dlci dlci-numNo ip multicast-routing IP Routing CommandsTable C-5. IP Routing Commands No ip routingBridge Commands Table C-6. Bridge Commands 1Example bridge crb 1 route ip Example no bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif No bridge-group bridge-groupExample arp timeout ARP CommandsTable C-7. ARP Commands Arp timeout time No arp timeout timeNo ip nat inside outside NAT CommandsTable C-8. NAT Commands 1 Example ip nat translation timeoutNo ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 2Ip nat pool pool-name start-ip-addr end-ip-addr Netmask netmask prefix-length / prefix-lengthTable C-8. NAT Commands 3 Clear ip nat translationFrom previous No ip dhcp pool pool-name Dhcp Server CommandsTable C-9. Dhcp Server Commands 1 No service dhcpDns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 2Default-router ip-address No default-router ip-address Domain-name domain-name No domain-name domain-nameNetwork network-num Table C-9. Dhcp Server Commands 3Example ip dhcp relay max-clients Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands No ip dhcp-server ip-addressNo access-list access-list-numpermit deny Filter access-list CommandsTable C-11. Filter Commands 1 Access-list access-list-num permit denyFor Extended IP Access Lists Table C-11. Filter Commands 2Table C-11. Filter Commands 3 For Protocol Type Access ListsExample access-list 200 permit 0x200 range No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4Table C-12. Diagnostic Commands 1 Diagnostic CommandsTraceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2Show arp Show CommandsTable C-13. Show Commands 1 Show configurationShow interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 2Show configuration saved unsaved Show frame-relay mapShow ip route ip-address Table C-13. Show Commands 3Show ip dhcp binding ip-address Show ip nat translationsTable C-13. Show Commands 4 Show ip trafficShow spanning-tree Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type CodesTable C-14. Ethernet Type Codes Hex 2 Description Protocol and Port Designations Icmp DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries ShortcutsShow Command Summary Table D-1. Show Commands FunctionIntf-type intf-num .sub-intf-num Table D-2. Access Control and System Level Commands Function Access Control and System Level Command SummaryDns-serverip-address CLI Command SummaryTable D-3. CLI Commands 1 Clear counters intf-type intf-num .sub-intf-numEncapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2CLI Command Default Settings Rear Panels Connectors, Cables, and Pin AssignmentsConnectors, Cables, and Pin Assignments Model COM Port for 9126 and 9128-II 25-Position COM Port ConnectorSignal Direction Pin # Pin # Signal DirectionModular Plug DB9 Socket COM Port-to-PC Cable Feature No -F2-550COM Port for 9128-II Carrier Mount COM Port Non-Keyed PositionCOM Port-to-Terminal/Printer Cable Feature No -F2-540 COM Port Non-KeyedPosition Modular Plug DB25 Plug Cisco 2500 Series Router RJ45 Jack COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port AUX Port Signal DB25 Pin # Direction COM Port-to-Router CablesCOM Port Console Port Signal DB25 Pin # Direction DB9 Pin # COM Port AUX Port Signal RJ45 Pin # Direction3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # DTR RTS Gender Adapter/ChangerLAN Adapter Converter and Cable Plug-to-Modular Jack Converter Com Port Position DB25 PlugDirection Pin Socket DTE Port ConnectorPin Standard V.35 Straight-through CableStandard V.35 Crossover Cable MM NNPosition DB15 Modular Plug Socket Unkeyed DSX-1 ConnectorDSX-1 Adapter Feature No -F1-560 Function Circuit Direction Pin NumberDSX-1 Port for 1-Slot 9128-II 15-Position T1 Network Cable Feature No -F1-500 T1 Mass Termination Cable Feature No -F1-500Function Circuit Line # Pin # Ethernet Port Connector Canadian T1 Line Interface Cable Feature No -F1-510Plug Unkeyed Modem Connector Isdn DBM ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Physical Environment Table F-1. NAM Technical Specifications 1 CriteriaPhysical Dimensions ApprovalsTable F-1. NAM Technical Specifications 2 Criteria Ethernet Port Table F-1. NAM Technical Specifications 3 CriteriaIsdn PRI DBM Interface B8ZSPower Consumption Dissipation Isdn BRI DBM Interface BRI, NI-1Ethernet Port FrameSaver AC Power Requirements Typical Power ConsumptionHeat Dissipation Max Standards Compliance Switch CompatibilityService Supported Switched Network InterfaceFraming Format Coding FormatLine Build-Out LBO FrameSaver SLV Units Model/FeatureEquipment Description NumberEquipment List Isdn PRI DBM NMS Products FrameSaver SLM Feature Set UpgradeOptional Features Power SuppliesSeries Access Carrier 9128-II NAM only Cables Description Part Number Feature NumberIN-1 IndexIN-2 BecnCLI Dhcp IN-3DBM IN-4IN-5 EEREIR IN-6 IN-7 LANIP SLV IN-8 LOFLOS NMS IN-9OID IN-10Port IN-11IN-12 IN-13 IN-14 IN-15 IN-16

Related manuals

Manual 32 pages 12.58 Kb