Paradyne CSU, DSU, 9126-II, 9128-II manual System Frame Relay and LMI Options 3

Page 67

4. Configuration Options

Table 4-1. System Frame Relay and LMI Options (3 of 4)

LMI Error Event (N2)

Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10

Default Setting: 3

Configures the LMI-defined N2 parameter, which sets the number of errors that can occur on the LMI link before an error is reported. Applies to both the user and network sides of a UNI.

1 – 10 – Specifies the maximum number of errors.

LMI Clearing Event (N3)

Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10

Default Setting: 1

Configures the LMI-defined N3 parameter, which sets the number of error-free messages that must be received before clearing an error event. Applies to both the user and network sides of a UNI.

1 – 10 – Specifies how many error-free messages it will take to clear the error event.

LMI Status Enquiry (N1)

Possible Settings: 1, 2, 3, 4, . . . 255

Default Setting: 6

Configures the LMI-defined N1 parameter, which sets the number of status enquiry polling cycles that the user side of the LMI initiates before a full status enquiry is initiated. Applies to the user side of a UNI only.

1 – 255 – Specifies the number of status enquiry polling cycles that can be initiated before a full status enquiry is initiated.

LMI Heartbeat (T1)

Possible Settings: 5, 10, 15, 20, 25, 30

Default Setting: 10

Configures the LMI-defined T1 parameter, which sets the number of seconds between the initiation of status enquiry messages on the user side of the LMI. Applies to the user side of a UNI only.

5 – 30 – Specifies the number of seconds between the initiation of status enquiry messages in increments of 5.

LMI Inbound Heartbeat (T2)

Possible Settings: 5, 10, 15, 20, 25, 30

Default Setting: 15

Configures the LMI-defined T2 parameter, which sets the number of seconds between the receipt of status enquiry messages on the network side of the LMI. Applies to the network side of a UNI only.

5 – 30 – Specifies the number of seconds between the receipt of status enquiry messages in increments of 5.

9128-A2-GB20-80

September 2002

4-23

Image 67

Contents FrameSaver SLV Trademarks Warranty, Sales, Service, and Training InformationCopyright 2002 Paradyne Corporation All rights reserved Document FeedbackContents Configuration Options ConfigurationTProceduresSeptember Iii Configuring the FrameSaver SLV RouterOperation and Maintenance Security and LoginsTroubleshooting Lamp Test Vii Setting Up NetScout Manager Plus for FrameSaver DevicesSetting Up Network Health for FrameSaver Devices Menu HierarchyTRouter CLI TCommands, Codes, and Designations Snmp MIBs and Traps, and Rmon Alarm DefaultsViii Connectors, Cables, and Pin Assignments Router Command Line Summaries and ShortcutsIndex Technical Specifications Equipment ListDocument Organization Purpose and Intended AudienceSection Description Section Description XiiXiii Product-Related DocumentsDocument Number Document Title Xiv Conventions UsedSystem Overview About the FrameSaver SLVRouter-Specific Features CSU/DSU-Specific FeaturesAbout the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Maximum Number of PVCs and Management PVCs Supported FrameSaver SLV Feature RouterThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II FeaturesFrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On ProcedureIf your login was Hen Select Main MenuScreen Format Description Screen Work AreasKeyboard Keys Navigating the ScreensPress For the screen Select Function Press Enter to Function KeysSelecting from a Menu Switching Between Screen AreasSelecting a Field Screen ContentsEntering Information CLI Keyboard Keys Navigating the Router’s CLIBasic Configuration Configuration ProceduresIsdn Configuration MenuConfiguration Option Area Description Configuration Option AreasMain Menu → Configuration Accessing and Displaying Configuration OptionsConfiguration → PVC Connections Changing Configuration OptionsSaving Configuration Options Configuration Options Configuration Options Main Menu → Easy Install Using the Easy Install FeatureEasy Install Screen Example Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUsMain Menu → Control→ System Information Entering System Information and Setting the System ClockIf the selection is Enter Valid characters include For Setting Up the ModemSetting Up Call Directories for Trap Dial-Out Main Menu → Control→ Modem Call DirectoriesSetting Up to Use the Modem PassThru Feature Main Menu → Auto-Configuration Setting Up Auto-ConfigurationAuto-Configuration Screen Example Only applies to models with Selecting a Frame Relay Discovery ModeMain Menu → Auto-Configuration→Frame Relay Discovery Mode Discovery Mode Configuration DescriptionDiscovery Mode Configuration Description Automatically Removing a Circuit Setting Up the DBM Physical Interface Setting Up Dial BackupMain Menu → Configuration → Isdn → Physical If you select Then Setting Up Automatic Backup ConfigurationFollowing prompt When Appears If you select Delete unused Remove AlternateDestinations From PVCsFor Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Isdn → Link ProfilesModifying Isdn Link Profiles Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup TimersAssigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp TrapsMain Menu → Control→ Change Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Changing Operating ModeConfiguration Option Tables System Frame Relay and LMI Options 1 Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs Main Menu → Configuration → System → Frame Relay and LMISystem Frame Relay and LMI Options 2 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsCode Points Assigned Class of Service DefinitionsClass of Svc Name Measure Latency & AvailabilityName Code Point DefinitionsCode Point Definitions Code PntSLV Sample Interval secs Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Type Available Settings Standard, COS 1-COSSLV Timeout Clearing Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Error Event ThresholdSLV Latency Clearing Event Threshold Service Level Verification Options 3SLV Packet Size bytes General System Options 1 Configuring General System OptionsMain Menu → Configuration → System→ General Test TimeoutGeneral System Options 2 General System Options 3 System Alarm RelayNetwork Physical Interface Options 1 Configuring Physical InterfacesConfiguring the Network Interface Main Menu → Configuration → Network→ PhysicalTransmit Timing Line Build Out LBO Possible Settings 0.0, -7.5, -15Network Physical Interface Options 2 Bit StuffingAnsi Performance Report Messages Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Physical Interface Options 3 Network Initiated PLBCircuit Identifier Network Physical Interface Options 4Data Port Physical Interface Options 1 Configuring a User Data Port CSU/DSUsMain Menu → Configuration → Data Ports→ Physical Port Use Possible Settings Frame Relay, Synchronous DataTransmit Clock Source Data Port Physical Interface Options 2Max Port Rate Kbps Port Base Rate KbpsMonitor RTS Control Data Port Physical Interface Options 3Monitor DTR Port DTE Initiated Loopbacks Data Port Physical Interface Options 4Invert Transmit and Receive Data Data Port Physical Interface Options 5 Action on Network Yellow AlarmInterface Status Configuring the DSX-1 InterfaceMain Menu → Configuration → DSX-1 DSX-1 Physical Interface Options 1Send All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2Local Phone Number 1 or Configuring the Isdn DBM InterfaceService Profile ID Spid 1 or Isdn BRI DBM Physical Interface Options10. Isdn PRI DBM Physical Interface Options 1 Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESSLocal Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Link Name Setting Up Isdn Link ProfilesMain Menu → Configuration → Isdn → Isdn Link Profiles 11. Isdn Link Profile Options 1Maximum Link Rate Kbps 11. Isdn Link Profile Options 2Outbound Phone Number Inbound Calling ID 1 orAlternate Outbound Phone Number Assigning Time Slots/Cross Connections11. Isdn Link Profile Options 3 Caller Identification MethodFrame Relay Network Time Slot Assignment Screen Example Assigning Frame Relay Time Slots to the Network InterfaceValue Meaning Time Slot Assignment Rule Assigning DSX-1 Time Slots to the Network InterfaceNtt Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen ExampleDSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen ExamplePhysical Interface Options Clearing Assignments13. Interface Frame Relay Options 1 Configuring Frame Relay for an InterfaceLMI Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 2Traffic Policing LMI Parameters13. Interface Frame Relay Options 3 14. Dlci Record Options 1 Manually Configuring Dlci RecordsDlci Number CIR bps 14. Dlci Record Options 2Committed Burst Size Bc Bits Outbound Management Priority 14. Dlci Record Options 3Excess Burst Size Bits Dlci Priority14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, NoneSource Dlci Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections 15. PVC Connection Options 1Primary Destination Dlci 15. PVC Connection Options 2Source Edlci Primary Destination LinkAlternate Destination Dlci 15. PVC Connection Options 3Primary Destination Edlci Alternate Destination LinkAlternate Destination Edlci 15. PVC Connection Options 4Enter IP Address press ESC to abort ... FWD No Configuring the IP Path ListMain Menu → Configuration → IP Path List Static 16. IP Path ListSetting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information17. Node IP Options 2 TS Access Management LinkTS Management Snmp Validation 17. Node IP Options 318. Management PVC Options 1 Configuring Management PVCsPayload Managed 18. Management PVC Options 2Set DE Primary Dlci 18. Management PVC Options 3Primary Edlci 18. Management PVC Options 4Alternate Dlci 18. Management PVC Options 5Alternate Edlci Encapsulation 18. Management PVC Options 6Snmp Management Configuring General Snmp ManagementName 1 Access 19. General Snmp Management Options 1Name 2 Access Configuring Telnet and/or FTP Session Support19. General Snmp Management Options 2 20. Telnet and FTP Session Options 1 Telnet Login RequiredTelnet Session 20. Telnet and FTP Session Options 2 Number of Managers Configuring Snmp NMS Security21. Snmp NMS Security Options 1 NMS IP Validation21. Snmp NMS Security Options 2 Configuring Snmp Traps and Trap Dial-Out22. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 22. Snmp Traps and Trap Dial-Out Options 3 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps Rmon Traps Possible Settings Network, Ports, DBM, All, None22. Snmp Traps and Trap Dial-Out Options 4 Dlci Traps on Interfaces Filter Selection FieldTrap Disconnect Dial-Out Delay TIme Min22. Snmp Traps and Trap Dial-Out Options 5 Trap Dial-OutIP SLV Availability Traps 22. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory Latency Traps23. Ethernet Management Options 1 Configuring Ethernet ManagementProxy ARP 23. Ethernet Management Options 224. Communication Port Options 1 Configuring the Communication PortCharacter Length Stop Bits Login Required24. Communication Port Options 2 Parity24. Communication Port Options 3 RIP 24. Communication Port Options 425. Modem Port Options 1 Configuring the Modem Port100 24. Communication Port Options 525. Modem Port Options 2 10125. Modem Port Options 3 10225. Modem Port Options 4 103104 Configuring the Criteria for Automatic BackupMain Menu → Configuration → Auto Backup Criteria 26. Auto Backup Criteria Options 1Backup Allowed Day To nnnn 26. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day From nnnn106 Configuring the FrameSaver SLV Router Network Interface FrameSaver SLV Router OverviewEthernet IP Routing Address Resolution ProtocolProxy ARP Interface Configuration IP Options Processing Network Address TranslationApplications Supported by NAT NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration ExampleSave exit Network Address Port Translation Napt Configuration ExampleNapt Mapping Public IP Address Private IP Addresses Ip nat inside source list 1 interface se 0.x overload Access-list 1 permit 10.1.3.0Int ethernet 0 ip nat inside int serial 0.x ip nat outside Ip nat inside source static 10.1.1.1 NAT and Napt Configuration ExampleDynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration ExampleDhcp Relay Agent Dhcp Server at Remote Site Configuration ExampleIP Router Filtering Router SecurityBridge Filtering Smurf Attack Prevention Provisioning the Router InterfaceIP Filtering Land Bug PreventionConfiguring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting AccessSet the configuration option Limiting Dial-In Access via the Modem Port Disabling Isdn Access Controlling Isdn AccessIsdn Call Security Limiting Telnet Access Controlling Telnet or FTP AccessLimiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp AccessAssigning Snmp Community Names and Access Levels Management and Communication → Limiting Snmp Access Through IP AddressesMain Menu → Configuration → General Snmp Management → Snmp Management EnableMain Menu → Control→ Administer Logins Creating a LoginField Enter Deleting a Login Modifying a LoginAccess Levels Command Modes Controlling Router CLI AccessLargo End Changing Access LevelsEnable Enable password passwordSecurity and Logins September Operation and Maintenance Operation and Maintenance Main Menu → Status → Identity Displaying System InformationView this field To find Isdn DBM Viewing LEDs and Control LeadsFrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLVDisplay LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control LeadsMain Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control LeadsALM LED DescriptionsGeneral Status LEDs 1 Label Indiction Color What It Means9128-II General Status LEDs 2Contd ModelEthernet Port LED Routers Only Network, DSX, or PRI Interface LEDsLabel Indication Color What It Means User Data Port LED CSU/DSUs OnlyUser Data Port Control Lead DescriptionsAdditional Control Leads Label Indication What It Means Network InterfaceTerminal Device MessagesDevice Messages 1 What It Indicates What To Do Seen at an FTPSee Changing Software on Device Messages 2 What It Indicates What To DoPVC Device Messages 3 What It Indicates What To DoDevice Messages 4 What It Indicates What To Do II only Reset COM Port usageDevice Messages 5 What It Indicates What To Do FrameSaver SLVDevice Messages 6 What It Indicates What To Do Status Menu Example Status InformationSelf-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Main Menu → Status → System and Test StatusIsdn PRI DBM only Change Operating ModeHealth and Status Messages Health and Status Messages 1 What It IndicatesFrame relay link 1,2 Health and Status Messages 2 What It IndicatesFrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It IndicatesNnnn, framerelaylink 1,2 Series Access Carrier onlyHealth and Status Messages 5 What It Indicates PathIP Address DownHealth and Status Messages 6 What It Indicates Health and Status Messages 7 What It Indicates Configuration→ Time Slot Assignment → FrameRelay Network Assignments and an LMI failure is Framerelaylink 1 ,3 Test Status MessagesTest Status Messages 1 What It Indicates Dclb Active, framerelaylink 1 orTest Status Messages 2 What It Indicates Main Menu → Status→ LMI Reported DLCIs Network LMI-Reported DLCIs StatusLMI-Reported DLCIs Status Screen Example Tframe relay network, or Main Menu → Status→ IP Path Connection Status IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates Main Menu → Status→ PVC Connection Status PVC Connection StatusPVC Connection Status Screen Example MgmtPVCName 12. PVC Connection Status 1 Field What It IndicatesEdlci Status What It Indicates 12. PVC Connection Status 2 FieldNetwork Timeslot Assignment Status Screen Example Time Slot Assignment StatusDisplaying Network Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status → NetworkDSX-1 Timeslot Assignment Status Screen Example Cross Connect Status Field bottom IndicatesDisplaying DSX-1 Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status→ DSX-1Main Menu → Status→ DBM Interface Status DBM Interface StatusDBM Interface Status Screen Example Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It IndicatesDelivered In Est Chnl-7 Link Name Disabled13. DBM Interface Status 2 Field What It Indicates Awarded and BeingChnl-7 13. DBM Interface Status 3 Field What It IndicatesValue is Call Awarded Being Delivered In EstMost Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance 15. IP Routing Table Values 1 Column What It Indicates IP Routing TableMain Menu → Status→ IP Routing Table IP Routing Table Screen ExampleTTL 15. IP Routing Table Values 2 Column What It IndicatesMain Menu → Status→ Performance Statistics Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance StatisticsVerification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration OptionsSize is changed, a new average is not available until a new Main Menu → Status → Performance Statistics→ Dlci Dlci Performance Statistics18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics→ Frame Relay For FrameSaver units with an Isdn DBM20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay ErrorsFrame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc ErrorsMain Menu → Status → Performance Statistics→ ESF Line ESF Line Performance StatisticsTo select intervals You must enter an interval or time on Lofc ESF Line Performance Statistics Screen ExampleLofc UAS22. DBM Call Performance Statistics What It Indicates DBM Call Performance StatisticsMain Menu → Status → Performance Statistics → Ethernet Ethernet Performance Statistics23. Ethernet Performance Statistics What It Indicates Main Menu → Status → Trap Event Log Trap Event LogTrap Event Log Screen Example Main Menu → Control→ Disable Modem PassThru to COM Activating the Modem PassThru FeatureCanceling Modem PassThru Operation Main Menu → Control→ Enable Modem PassThru to COMVerifying Modem Operation Manually Disconnecting the ModemMain Menu → Control→ Disconnect Modem Isdn DBM Operation Forcing Backup DisruptiveMain Menu→ Test→ Isdn Call/PVC Tests Placing a Test Call NondisruptiveIf the Result is Then Verifying Isdn Lines Verifying That Backup Can Take PlaceSystem Operational should appear FTP File Transfers Command Definition If the message displayed is Then Upgrading System SoftwareMain Menu → Status→ Identity Upgrading Isdn BRI DBM SoftwareChanging Software Determining Whether a Download Is CompletedMain Menu → Control→ Select Software Release If retrieving Hen Transferring Collected DataMain Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm RelayOperation and Maintenance September Troubleshooting Main Menu → Status → Display LEDs and Control LEDs Problem IndicatorsIndicators See Operation and MaintenanceResetting the Unit from the Control Menu Resetting the Unit and Restoring CommunicationResetting the Unit By Cycling the Power If selecting He following occurs Restoring Communication with an Improperly Configured UnitLMI Packet Capture Utility Feature Troubleshooting Management Link FeatureLMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace LogAlarm Conditions 1 What It Indicates What To Do AlarmsMenu → Control → Reset Device IPAddress Alarm Conditions 2 What It Indicates What To DoMain Menu → Configuration → Isdn → Link Profiles NameLink Alarm Conditions 3 What It Indicates What To DoMenu→ Configuration→ LMI Down, frame relayDTE Alarm Conditions 4 What It Indicates What To DoPathIP Address Alarm Conditions 5 What It Indicates What To DoNnnn , frame relay Alarm Conditions 6 What It Indicates What To DoAlarm Conditions 7 What It Indicates What To Do Viewing the Trap Event Log Troubleshooting TablesDevice Problems Device Problems 1 Symptom Possible Cause SolutionsImproperly Configured Unit on Device Problems 2 Symptom Possible Cause SolutionsFrame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC ProblemsIsdn DBM Problems Symptom Possible Cause Solutions Isdn DBM ProblemsMain Menu → Status → DBM Interface Status Test Menu Example Tests AvailableDBM Tests Test Timeout FeatureStarting and Stopping a Test When the status of a test is Only command available isAborting All Tests PVC Tests Screen Example PVC TestsMain Menu → Test→ Isdn Call/PVC Tests PVC LoopbackMain Menu → Test→ Network PVC Test Main Menu → Test→ Data Port PVC TestsIsdn Call/PVC Tests Send PatternMonitor Pattern Network PVC Tests/Data Port PVC TestsTest Call ConnectivityPhysical Tests Screen Example Physical TestsMain Menu → Test→ Network Physical Tests Line LoopbackLLB PLB Payload LoopbackRLB AIS Repeater LoopbackDtlb DTE DTE LoopbackMain Menu → Test→ Data Port Physical Tests DSXSend Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line LoopbackQrss Send and Monitor Pattern TestsPing Screen Example IP Ping TestTarget IP Address Ping Options 1Packet Size Inter-Ping DelayPing Options 2 Source IP AddressPing Options 3 Response TimeoutPing Responses Field Possible Values Description Main Menu → Test→ IP Ping IP Ping Test ProcedureMain Menu → Test→ Lamp Test Lamp TestHis chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM SystemSetting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set ActivationsActivation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation CertificateScheduling Activations Accessing and Printing the Certificate Summary Report Canceling Scheduled ActivationsChecking the Status of Scheduled Activations 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver DevicesProperties AlarmsPreparation 10-210-3 Configuring NetScout Manager Plus10-4 10-5 Verifying Domains and Groups10-6 Correcting Domains and Groups10-7 Property Description Setting10-8 Adding SLV Alarms Using a Template10-9 Editing Alarms10-10 10-11 Adding SLV Alarms ManuallyField Select or Enter 10-12Paradyne 10-13 Creating History FilesChange 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-1410-15 Installing the User-Defined History FilesDvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Dvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh10-16 Monitoring a DLCI’s History Data10-17 10-18 Monitoring the Agent Using NetScout Manager Plus10-19 10-20 Statistical Windows SupportedTraffic Statistics Protocol Statistics 11-1 Setting Up Network Health for FrameSaver Devices11-2 Installation and Setup of Network Health11-3 Discovering FrameSaver Elements11-4 Configuring the Discovered Elements11-5 Grouping Elements for Reports11-6 About Service Level ReportsGenerating Reports for a Group About At-a-Glance Reports11-7 Reports Applicable to SLV DevicesAbout Trend Reports Printed Reports11-8 FrameSaver SLV Plus At-a-Glance Report 11-911-10 Menus Menu HierarchyStatus Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB SupportFrameSaver Unit’s sysObjectID system System Group mib-2Interfaces Group mib-2 FrameSaver Unit’s sysDescr systemFrame Relay Logical Layer Profile Link Name NAMNetScout Indexes to the Interface Table ifTable FR Service T1 FR NAMFR DTE T1 FR NAM Number Dlci number DTE Rmon Logical LayerIfName of the interface Number Dlci number ALLExamples Standards Compliance for Snmp TrapsVariable-Binding Trap authenticationFailureTrap warmStart Table B-3. warmStart Trap What It Indicates Possible CauseTraps linkUp and linkDown Strings Physical SublayerPRI MIBLogical Link Sublayer BRIXxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific‘Path xxx.xxx.xxx.xxx Up Nnnn ’That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControlDial Control Extension MIB Rmon Alarm and Event DefaultsEvent Defaults EventIndex EventDescription EventType EventCommunityRising Event Operation Physical Interface Alarm DefaultsFrame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne AreaDlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order MIB Rmon II RFC 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 6.1.2.1.16.12.2.1CIR 6.1.4.1.1795.2.24.26.1.4.1.1795.2.24.2.6.9.4 Dlci CIRDlci EIR 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.16.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Xxxxxxxxxxxx CLI CommandsConvention Meaning X.xRouter CLI Commands, Codes, and Designations Table C-2. Access Control Commands Pager CommandAccess Control Commands Table C-1. Pager CommandExample configure terminal Configuration CommandsTable C-3. Configuration Commands Configure terminal factoryExample interface serial 132.53.4.2 Interface CommandsTable C-4. Interface Commands 1 Command Mode config, config-if, config-subifExample encapsulation frame-relay ietf Table C-4. Interface Commands 2Encapsulation encapsulation-type encapsulation-protocol Example ip address 132.53.4.2Example ip unnumbered Table C-4. Interface Commands 3No ip unnumbered null No frame-relay interface-dlci dlci-numNo ip multicast-routing IP Routing CommandsTable C-5. IP Routing Commands No ip routingTable C-6. Bridge Commands 1 Bridge CommandsExample bridge crb 1 route ip Example no bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif No bridge-group bridge-groupExample arp timeout ARP CommandsTable C-7. ARP Commands Arp timeout time No arp timeout timeNo ip nat inside outside NAT CommandsTable C-8. NAT Commands 1 Example ip nat translation timeoutNo ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 2Ip nat pool pool-name start-ip-addr end-ip-addr Netmask netmask prefix-length / prefix-lengthClear ip nat translation Table C-8. NAT Commands 3From previous No ip dhcp pool pool-name Dhcp Server CommandsTable C-9. Dhcp Server Commands 1 No service dhcpDns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 2Default-router ip-address No default-router ip-address Domain-name domain-name No domain-name domain-nameNetwork network-num Table C-9. Dhcp Server Commands 3Example ip dhcp relay max-clients Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands No ip dhcp-server ip-addressNo access-list access-list-numpermit deny Filter access-list CommandsTable C-11. Filter Commands 1 Access-list access-list-num permit denyFor Extended IP Access Lists Table C-11. Filter Commands 2For Protocol Type Access Lists Table C-11. Filter Commands 3Example access-list 200 permit 0x200 range No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4Table C-12. Diagnostic Commands 1 Diagnostic CommandsTraceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2Show arp Show CommandsTable C-13. Show Commands 1 Show configurationShow interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 2Show configuration saved unsaved Show frame-relay mapShow ip route ip-address Table C-13. Show Commands 3Show ip dhcp binding ip-address Show ip nat translationsShow ip traffic Table C-13. Show Commands 4Show spanning-tree Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type CodesTable C-14. Ethernet Type Codes Hex 2 Description Icmp Designations Protocol and Port DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries ShortcutsTable D-1. Show Commands Function Show Command SummaryIntf-type intf-num .sub-intf-num Table D-2. Access Control and System Level Commands Function Access Control and System Level Command SummaryDns-serverip-address CLI Command SummaryTable D-3. CLI Commands 1 Clear counters intf-type intf-num .sub-intf-numEncapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2CLI Command Default Settings Rear Panels Connectors, Cables, and Pin AssignmentsConnectors, Cables, and Pin Assignments Model COM Port for 9126 and 9128-II 25-Position COM Port ConnectorSignal Direction Pin # Pin # Signal DirectionModular Plug DB9 Socket COM Port-to-PC Cable Feature No -F2-550COM Port for 9128-II Carrier Mount COM Port Non-Keyed PositionCOM Port Non-Keyed COM Port-to-Terminal/Printer Cable Feature No -F2-540Position Modular Plug DB25 Plug Cisco 2500 Series Router RJ45 Jack COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port AUX Port Signal DB25 Pin # Direction COM Port-to-Router CablesCOM Port AUX Port Signal RJ45 Pin # Direction COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # DTR RTS Gender Adapter/ChangerLAN Adapter Converter and Cable Plug-to-Modular Jack Converter Com Port Position DB25 PlugDirection Pin Socket DTE Port ConnectorPin Standard V.35 Straight-through CableStandard V.35 Crossover Cable MM NNPosition DB15 Modular Plug Socket Unkeyed DSX-1 ConnectorDSX-1 Adapter Feature No -F1-560 Function Circuit Direction Pin NumberDSX-1 Port for 1-Slot 9128-II 15-Position T1 Mass Termination Cable Feature No -F1-500 T1 Network Cable Feature No -F1-500Function Circuit Line # Pin # Canadian T1 Line Interface Cable Feature No -F1-510 Ethernet Port ConnectorPlug Unkeyed Isdn DBM Connector Modem ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Physical Environment Table F-1. NAM Technical Specifications 1 CriteriaPhysical Dimensions ApprovalsTable F-1. NAM Technical Specifications 2 Criteria Ethernet Port Table F-1. NAM Technical Specifications 3 CriteriaIsdn PRI DBM Interface B8ZSPower Consumption Dissipation BRI, NI-1 Isdn BRI DBM InterfaceEthernet Port FrameSaver Typical Power Consumption AC Power RequirementsHeat Dissipation Max Standards Compliance Switch CompatibilityService Supported Switched Network InterfaceCoding Format Framing FormatLine Build-Out LBO FrameSaver SLV Units Model/FeatureEquipment Description NumberEquipment List Isdn PRI DBM NMS Products FrameSaver SLM Feature Set UpgradeOptional Features Power SuppliesSeries Access Carrier 9128-II NAM only Cables Description Part Number Feature NumberIN-1 IndexBecn IN-2CLI Dhcp IN-3DBM IN-4EER IN-5EIR IN-6 LAN IN-7IP SLV LOF IN-8LOS NMS IN-9OID IN-10Port IN-11IN-12 IN-13 IN-14 IN-15 IN-16

Related manuals

Manual 32 pages 12.58 Kb