Paradyne 9126, CSU, DSU Remove Alternate, Destinations, From PVCs, Delete unused, Dlci Records?

Page 59

4. Configuration Options

 

The following prompt

 

When the . . .

appears . . .

If you select . . .

 

 

 

Response to the

—

No – No previously configured

Remove Alternate

 

DLCIs, ISDN Link Profiles, or

Destinations

 

PVC Connections are removed

from PVCs and

 

or changed, but updates due to

delete unused

 

LMI responses will be

DLCI Records?

 

performed using the new

Tprompt was Yes, and

 

Tsetting.

Automatic Backup

 

Yes – All Alternate Destination

Configuration was

 

information will be removed

disabled

 

from PVC Connections and

 

 

Management PVCs, and all

 

 

DLCIs and ISDN Link Profiles

 

 

(except for the first one) used

 

 

exclusively as Alternate

 

 

Destinations are deleted.

 

 

 

Response to the

Add Alternate

No – No previously configured

Remove Alternate

Destinations to

PVC Connections are removed

Destinations

Current PVC

or changed, but updates due to

from PVCs and

Connections?

LMI responses will be

delete unused

 

performed using the new

DLCI Records?

 

setting.

prompt was Yes, and

 

Yes – Alternate Destination

 

 

Automatic Backup

 

information is configured for

Configuration was set

 

current DLCIs, ISDN Link

to

 

Profiles, PVC Connections and

Single_Site_Backup

 

Management PVCs on the

or Multi_Site_Backup

 

ISDN DBM interface, except for

 

 

the Management PVC

 

 

designated as the TS Access

 

 

Management Link.

 

 

 

NOTE:

When DLCIs, PVC connections, and management PVCs for the first ISDN Link Profile have been configured manually, it is recommended that specific discovered DLCIs, PVC connections, and management PVCs be deleted manually via the Configuration menus. Otherwise, the manual configurations will be deleted along with the automatically configured ones.

To specify when automatic backup is allowed or can occur, see Configuring the Criteria for Automatic Backup on page 4-104.

9128-A2-GB20-80

September 2002

4-15

Page 58 Page 60
Image 59
Page 58 Page 60
Contents FrameSaver SLV Trademarks Warranty, Sales, Service, and Training InformationCopyright 2002 Paradyne Corporation All rights reserved Document FeedbackContents September ConfigurationTProceduresConfiguration Options Iii Configuring the FrameSaver SLV RouterOperation and Maintenance Security and LoginsTroubleshooting Lamp Test Vii Setting Up NetScout Manager Plus for FrameSaver DevicesSetting Up Network Health for FrameSaver Devices Menu HierarchyTViii Snmp MIBs and Traps, and Rmon Alarm DefaultsRouter CLI TCommands, Codes, and Designations Connectors, Cables, and Pin Assignments Router Command Line Summaries and ShortcutsIndex Technical Specifications Equipment ListSection Description Purpose and Intended AudienceDocument Organization Section Description XiiDocument Number Document Title Product-Related DocumentsXiii Xiv Conventions UsedSystem Overview About the FrameSaver SLVRouter-Specific Features CSU/DSU-Specific FeaturesAbout the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Through 120 Connections PVCs Dedicated Management FrameSaver SLV Feature RouterMaximum Number of PVCs and Management PVCs Supported About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II FeaturesFrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On ProcedureIf your login was Hen Select Main MenuScreen Format Description Screen Work AreasPress Navigating the ScreensKeyboard Keys For the screen Select Function Press Enter to Function KeysSelecting from a Menu Switching Between Screen AreasEntering Information Screen ContentsSelecting a Field CLI Keyboard Keys Navigating the Router’s CLIBasic Configuration Configuration ProceduresIsdn Configuration MenuConfiguration Option Area Description Configuration Option AreasMain Menu → Configuration Accessing and Displaying Configuration OptionsConfiguration → PVC Connections Changing Configuration OptionsSaving Configuration Options Configuration Options Configuration Options Easy Install Screen Example Using the Easy Install FeatureMain Menu → Easy Install Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUsIf the selection is Enter Entering System Information and Setting the System ClockMain Menu → Control→ System Information Valid characters include For Setting Up the ModemSetting Up Call Directories for Trap Dial-Out Main Menu → Control→ Modem Call DirectoriesSetting Up to Use the Modem PassThru Feature Auto-Configuration Screen Example Setting Up Auto-ConfigurationMain Menu → Auto-Configuration Only applies to models with Selecting a Frame Relay Discovery ModeMain Menu → Auto-Configuration→Frame Relay Discovery Mode Discovery Mode Configuration DescriptionDiscovery Mode Configuration Description Automatically Removing a Circuit Main Menu → Configuration → Isdn → Physical Setting Up Dial BackupSetting Up the DBM Physical Interface If you select Then Setting Up Automatic Backup ConfigurationFollowing prompt When Appears If you select Delete unused Remove AlternateDestinations From PVCsModifying Isdn Link Profiles Main Menu → Configuration → Isdn → Link ProfilesFor Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup TimersAssigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp TrapsMain Menu → Control→ Change Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Changing Operating ModeConfiguration Option Tables System Frame Relay and LMI Options 1 Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs Main Menu → Configuration → System → Frame Relay and LMISystem Frame Relay and LMI Options 2 System Frame Relay and LMI Options 3 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsCode Points Assigned Class of Service DefinitionsClass of Svc Name Measure Latency & AvailabilityName Code Point DefinitionsCode Point Definitions Code PntSLV Sample Interval secs Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Type Available Settings Standard, COS 1-COSSLV Timeout Clearing Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Error Event ThresholdSLV Packet Size bytes Service Level Verification Options 3SLV Latency Clearing Event Threshold General System Options 1 Configuring General System OptionsMain Menu → Configuration → System→ General Test TimeoutGeneral System Options 2 General System Options 3 System Alarm RelayNetwork Physical Interface Options 1 Configuring Physical InterfacesConfiguring the Network Interface Main Menu → Configuration → Network→ PhysicalTransmit Timing Line Build Out LBO Possible Settings 0.0, -7.5, -15Network Physical Interface Options 2 Bit StuffingAnsi Performance Report Messages Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Physical Interface Options 3 Network Initiated PLBCircuit Identifier Network Physical Interface Options 4Data Port Physical Interface Options 1 Configuring a User Data Port CSU/DSUsMain Menu → Configuration → Data Ports→ Physical Port Use Possible Settings Frame Relay, Synchronous DataTransmit Clock Source Data Port Physical Interface Options 2Max Port Rate Kbps Port Base Rate KbpsMonitor DTR Data Port Physical Interface Options 3Monitor RTS Control Invert Transmit and Receive Data Data Port Physical Interface Options 4Port DTE Initiated Loopbacks Data Port Physical Interface Options 5 Action on Network Yellow AlarmInterface Status Configuring the DSX-1 InterfaceMain Menu → Configuration → DSX-1 DSX-1 Physical Interface Options 1Send All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2Local Phone Number 1 or Configuring the Isdn DBM InterfaceService Profile ID Spid 1 or Isdn BRI DBM Physical Interface OptionsLocal Phone Number Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS10. Isdn PRI DBM Physical Interface Options 1 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Link Name Setting Up Isdn Link ProfilesMain Menu → Configuration → Isdn → Isdn Link Profiles 11. Isdn Link Profile Options 1Maximum Link Rate Kbps 11. Isdn Link Profile Options 2Outbound Phone Number Inbound Calling ID 1 orAlternate Outbound Phone Number Assigning Time Slots/Cross Connections11. Isdn Link Profile Options 3 Caller Identification MethodValue Meaning Assigning Frame Relay Time Slots to the Network InterfaceFrame Relay Network Time Slot Assignment Screen Example Ntt Assigning DSX-1 Time Slots to the Network InterfaceTime Slot Assignment Rule Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen ExampleDSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen ExamplePhysical Interface Options Clearing AssignmentsLMI Configuring Frame Relay for an Interface13. Interface Frame Relay Options 1 Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 2Traffic Policing LMI Parameters13. Interface Frame Relay Options 3 Dlci Number Manually Configuring Dlci Records14. Dlci Record Options 1 Committed Burst Size Bc Bits 14. Dlci Record Options 2CIR bps Outbound Management Priority 14. Dlci Record Options 3Excess Burst Size Bits Dlci Priority14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, NoneSource Dlci Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections 15. PVC Connection Options 1Primary Destination Dlci 15. PVC Connection Options 2Source Edlci Primary Destination LinkAlternate Destination Dlci 15. PVC Connection Options 3Primary Destination Edlci Alternate Destination LinkAlternate Destination Edlci 15. PVC Connection Options 4Enter IP Address press ESC to abort ... FWD No Configuring the IP Path ListMain Menu → Configuration → IP Path List Static 16. IP Path ListSetting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information17. Node IP Options 2 TS Access Management LinkTS Management Snmp Validation 17. Node IP Options 318. Management PVC Options 1 Configuring Management PVCsSet DE 18. Management PVC Options 2Payload Managed Primary Dlci 18. Management PVC Options 3Primary Edlci 18. Management PVC Options 4Alternate Edlci 18. Management PVC Options 5Alternate Dlci Encapsulation 18. Management PVC Options 6Snmp Management Configuring General Snmp ManagementName 1 Access 19. General Snmp Management Options 119. General Snmp Management Options 2 Configuring Telnet and/or FTP Session SupportName 2 Access Telnet Session Telnet Login Required20. Telnet and FTP Session Options 1 20. Telnet and FTP Session Options 2 Number of Managers Configuring Snmp NMS Security21. Snmp NMS Security Options 1 NMS IP Validation22. Snmp Traps and Trap Dial-Out Options 1 Configuring Snmp Traps and Trap Dial-Out21. Snmp NMS Security Options 2 22. Snmp Traps and Trap Dial-Out Options 2 Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both22. Snmp Traps and Trap Dial-Out Options 3 Rmon Traps Possible Settings Network, Ports, DBM, All, None22. Snmp Traps and Trap Dial-Out Options 4 Dlci Traps on Interfaces Filter Selection FieldTrap Disconnect Dial-Out Delay TIme Min22. Snmp Traps and Trap Dial-Out Options 5 Trap Dial-OutIP SLV Availability Traps 22. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory Latency Traps23. Ethernet Management Options 1 Configuring Ethernet ManagementProxy ARP 23. Ethernet Management Options 2Character Length Configuring the Communication Port24. Communication Port Options 1 Stop Bits Login Required24. Communication Port Options 2 Parity24. Communication Port Options 3 RIP 24. Communication Port Options 425. Modem Port Options 1 Configuring the Modem Port100 24. Communication Port Options 525. Modem Port Options 2 10125. Modem Port Options 3 10225. Modem Port Options 4 103104 Configuring the Criteria for Automatic BackupMain Menu → Configuration → Auto Backup Criteria 26. Auto Backup Criteria Options 1Backup Allowed Day To nnnn 26. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day From nnnn106 Configuring the FrameSaver SLV Router Ethernet FrameSaver SLV Router OverviewNetwork Interface Proxy ARP Address Resolution ProtocolIP Routing Interface Configuration Applications Supported by NAT Network Address TranslationIP Options Processing NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration ExampleSave exit Napt Mapping Public IP Address Private IP Addresses Napt Configuration ExampleNetwork Address Port Translation Int ethernet 0 ip nat inside int serial 0.x ip nat outside Access-list 1 permit 10.1.3.0Ip nat inside source list 1 interface se 0.x overload Ip nat inside source static 10.1.1.1 NAT and Napt Configuration ExampleDynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration ExampleDhcp Relay Agent Dhcp Server at Remote Site Configuration ExampleBridge Filtering Router SecurityIP Router Filtering Smurf Attack Prevention Provisioning the Router InterfaceIP Filtering Land Bug PreventionConfiguring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting AccessSet the configuration option Limiting Dial-In Access via the Modem Port Isdn Call Security Controlling Isdn AccessDisabling Isdn Access Limiting Telnet Access Controlling Telnet or FTP AccessLimiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp AccessAssigning Snmp Community Names and Access Levels Management and Communication → Limiting Snmp Access Through IP AddressesMain Menu → Configuration → General Snmp Management → Snmp Management EnableField Enter Creating a LoginMain Menu → Control→ Administer Logins Deleting a Login Modifying a LoginLargo Controlling Router CLI AccessAccess Levels Command Modes End Changing Access LevelsEnable Enable password passwordSecurity and Logins September Operation and Maintenance Operation and Maintenance View this field To find Displaying System InformationMain Menu → Status → Identity Isdn DBM Viewing LEDs and Control LeadsFrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLVDisplay LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control LeadsMain Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control LeadsALM LED DescriptionsGeneral Status LEDs 1 Label Indiction Color What It Means9128-II General Status LEDs 2Contd ModelEthernet Port LED Routers Only Network, DSX, or PRI Interface LEDsLabel Indication Color What It Means User Data Port LED CSU/DSUs OnlyUser Data Port Control Lead DescriptionsAdditional Control Leads Label Indication What It Means Network InterfaceTerminal Device MessagesDevice Messages 1 What It Indicates What To Do Seen at an FTPSee Changing Software on Device Messages 2 What It Indicates What To DoPVC Device Messages 3 What It Indicates What To DoDevice Messages 4 What It Indicates What To Do II only Reset COM Port usageDevice Messages 5 What It Indicates What To Do FrameSaver SLVDevice Messages 6 What It Indicates What To Do Status Menu Example Status InformationSelf-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Main Menu → Status → System and Test StatusIsdn PRI DBM only Change Operating ModeHealth and Status Messages Health and Status Messages 1 What It IndicatesFrameSaver SLV 9126-II or Health and Status Messages 2 What It IndicatesFrame relay link 1,2 Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It IndicatesNnnn, framerelaylink 1,2 Series Access Carrier onlyHealth and Status Messages 5 What It Indicates PathIP Address DownHealth and Status Messages 6 What It Indicates Relay Network Assignments and an LMI failure is Configuration→ Time Slot Assignment → FrameHealth and Status Messages 7 What It Indicates Framerelaylink 1 ,3 Test Status MessagesTest Status Messages 1 What It Indicates Dclb Active, framerelaylink 1 orTest Status Messages 2 What It Indicates LMI-Reported DLCIs Status Screen Example Network LMI-Reported DLCIs StatusMain Menu → Status→ LMI Reported DLCIs Tframe relay network, or IP Path Connection Status Screen Example IP Path Connection StatusMain Menu → Status→ IP Path Connection Status 11. IP Path Connection Status Field What It Indicates PVC Connection Status Screen Example PVC Connection StatusMain Menu → Status→ PVC Connection Status Edlci 12. PVC Connection Status 1 Field What It IndicatesMgmtPVCName Status What It Indicates 12. PVC Connection Status 2 FieldNetwork Timeslot Assignment Status Screen Example Time Slot Assignment StatusDisplaying Network Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status → NetworkDSX-1 Timeslot Assignment Status Screen Example Cross Connect Status Field bottom IndicatesDisplaying DSX-1 Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status→ DSX-1DBM Interface Status Screen Example DBM Interface StatusMain Menu → Status→ DBM Interface Status Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It IndicatesDelivered In Est Chnl-7 Link Name Disabled13. DBM Interface Status 2 Field What It Indicates Awarded and BeingChnl-7 13. DBM Interface Status 3 Field What It IndicatesValue is Call Awarded Being Delivered In EstMost Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance 15. IP Routing Table Values 1 Column What It Indicates IP Routing TableMain Menu → Status→ IP Routing Table IP Routing Table Screen ExampleTTL 15. IP Routing Table Values 2 Column What It IndicatesPerformance Statistics Menu Performance StatisticsMain Menu → Status→ Performance Statistics Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance StatisticsVerification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration OptionsSize is changed, a new average is not available until a new 18. Dlci Performance Statistics 1 What It Indicates Dlci Performance StatisticsMain Menu → Status → Performance Statistics→ Dlci 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics→ Frame Relay For FrameSaver units with an Isdn DBM20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay ErrorsFrame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc ErrorsTo select intervals You must enter an interval or time on ESF Line Performance StatisticsMain Menu → Status → Performance Statistics→ ESF Line Lofc ESF Line Performance Statistics Screen ExampleLofc UAS22. DBM Call Performance Statistics What It Indicates DBM Call Performance Statistics23. Ethernet Performance Statistics What It Indicates Ethernet Performance StatisticsMain Menu → Status → Performance Statistics → Ethernet Trap Event Log Screen Example Trap Event LogMain Menu → Status → Trap Event Log Main Menu → Control→ Disable Modem PassThru to COM Activating the Modem PassThru FeatureCanceling Modem PassThru Operation Main Menu → Control→ Enable Modem PassThru to COMMain Menu → Control→ Disconnect Modem Manually Disconnecting the ModemVerifying Modem Operation Isdn DBM Operation Forcing Backup DisruptiveIf the Result is Then Placing a Test Call NondisruptiveMain Menu→ Test→ Isdn Call/PVC Tests System Operational should appear Verifying That Backup Can Take PlaceVerifying Isdn Lines FTP File Transfers Command Definition If the message displayed is Then Upgrading System SoftwareMain Menu → Status→ Identity Upgrading Isdn BRI DBM SoftwareMain Menu → Control→ Select Software Release Determining Whether a Download Is CompletedChanging Software If retrieving Hen Transferring Collected DataMain Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm RelayOperation and Maintenance September Troubleshooting Main Menu → Status → Display LEDs and Control LEDs Problem IndicatorsIndicators See Operation and MaintenanceResetting the Unit By Cycling the Power Resetting the Unit and Restoring CommunicationResetting the Unit from the Control Menu If selecting He following occurs Restoring Communication with an Improperly Configured UnitLMI Packet Capture Utility Feature Troubleshooting Management Link FeatureLMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace LogMenu → Control → Reset Device AlarmsAlarm Conditions 1 What It Indicates What To Do IPAddress Alarm Conditions 2 What It Indicates What To DoMain Menu → Configuration → Isdn → Link Profiles NameLink Alarm Conditions 3 What It Indicates What To DoMenu→ Configuration→ LMI Down, frame relayDTE Alarm Conditions 4 What It Indicates What To DoPathIP Address Alarm Conditions 5 What It Indicates What To DoNnnn , frame relay Alarm Conditions 6 What It Indicates What To DoAlarm Conditions 7 What It Indicates What To Do Viewing the Trap Event Log Troubleshooting TablesDevice Problems Device Problems 1 Symptom Possible Cause SolutionsImproperly Configured Unit on Device Problems 2 Symptom Possible Cause SolutionsFrame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC ProblemsMain Menu → Status → DBM Interface Status Isdn DBM ProblemsIsdn DBM Problems Symptom Possible Cause Solutions Test Menu Example Tests AvailableDBM Tests Test Timeout FeatureStarting and Stopping a Test When the status of a test is Only command available isAborting All Tests PVC Tests Screen Example PVC TestsMain Menu → Test→ Isdn Call/PVC Tests PVC LoopbackMain Menu → Test→ Network PVC Test Main Menu → Test→ Data Port PVC TestsIsdn Call/PVC Tests Send PatternMonitor Pattern Network PVC Tests/Data Port PVC TestsTest Call ConnectivityPhysical Tests Screen Example Physical TestsLLB Line LoopbackMain Menu → Test→ Network Physical Tests PLB Payload LoopbackRLB AIS Repeater LoopbackDtlb DTE DTE LoopbackMain Menu → Test→ Data Port Physical Tests DSXSend Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line LoopbackQrss Send and Monitor Pattern TestsPing Screen Example IP Ping TestTarget IP Address Ping Options 1Packet Size Inter-Ping DelayPing Options 2 Source IP AddressPing Responses Field Possible Values Description Response TimeoutPing Options 3 Main Menu → Test→ IP Ping IP Ping Test ProcedureMain Menu → Test→ Lamp Test Lamp TestHis chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM SystemSetting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set ActivationsActivation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation CertificateScheduling Activations Checking the Status of Scheduled Activations Canceling Scheduled ActivationsAccessing and Printing the Certificate Summary Report 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver DevicesProperties AlarmsPreparation 10-210-3 Configuring NetScout Manager Plus10-4 10-5 Verifying Domains and Groups10-6 Correcting Domains and Groups10-7 Property Description Setting10-8 Adding SLV Alarms Using a Template10-9 Editing Alarms10-10 10-11 Adding SLV Alarms ManuallyParadyne 10-12Field Select or Enter 10-13 Creating History FilesChange 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-1410-15 Installing the User-Defined History FilesDvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Dvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh10-16 Monitoring a DLCI’s History Data10-17 10-18 Monitoring the Agent Using NetScout Manager Plus10-19 Traffic Statistics Protocol Statistics Statistical Windows Supported10-20 11-1 Setting Up Network Health for FrameSaver Devices11-2 Installation and Setup of Network Health11-3 Discovering FrameSaver Elements11-4 Configuring the Discovered Elements11-5 Grouping Elements for Reports11-6 About Service Level ReportsGenerating Reports for a Group About At-a-Glance Reports11-7 Reports Applicable to SLV DevicesAbout Trend Reports Printed Reports11-8 FrameSaver SLV Plus At-a-Glance Report 11-911-10 Menus Menu HierarchyStatus Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB SupportFrameSaver Unit’s sysObjectID system System Group mib-2Interfaces Group mib-2 FrameSaver Unit’s sysDescr systemFrame Relay Logical Layer Profile Link Name NAMFR DTE T1 FR NAM FR Service T1 FR NAMNetScout Indexes to the Interface Table ifTable Number Dlci number DTE Rmon Logical LayerIfName of the interface Number Dlci number ALLExamples Standards Compliance for Snmp TrapsVariable-Binding Trap authenticationFailureTrap warmStart Table B-3. warmStart Trap What It Indicates Possible CauseTraps linkUp and linkDown Strings Physical SublayerPRI MIBLogical Link Sublayer BRIXxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific‘Path xxx.xxx.xxx.xxx Up Nnnn ’That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControlDial Control Extension MIB Rmon Alarm and Event DefaultsEvent Defaults EventIndex EventDescription EventType EventCommunityRising Event Operation Physical Interface Alarm DefaultsFrame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne AreaDlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order MIB Rmon II RFC 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 6.1.2.1.16.12.2.1CIR 6.1.4.1.1795.2.24.26.1.4.1.1795.2.24.2.6.9.4 Dlci CIRDlci EIR 6.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.16.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Xxxxxxxxxxxx CLI CommandsConvention Meaning X.xRouter CLI Commands, Codes, and Designations Table C-2. Access Control Commands Pager CommandAccess Control Commands Table C-1. Pager CommandExample configure terminal Configuration CommandsTable C-3. Configuration Commands Configure terminal factoryExample interface serial 132.53.4.2 Interface CommandsTable C-4. Interface Commands 1 Command Mode config, config-if, config-subifExample encapsulation frame-relay ietf Table C-4. Interface Commands 2Encapsulation encapsulation-type encapsulation-protocol Example ip address 132.53.4.2Example ip unnumbered Table C-4. Interface Commands 3No ip unnumbered null No frame-relay interface-dlci dlci-numNo ip multicast-routing IP Routing CommandsTable C-5. IP Routing Commands No ip routingExample bridge crb 1 route ip Bridge CommandsTable C-6. Bridge Commands 1 Example no bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif No bridge-group bridge-groupExample arp timeout ARP CommandsTable C-7. ARP Commands Arp timeout time No arp timeout timeNo ip nat inside outside NAT CommandsTable C-8. NAT Commands 1 Example ip nat translation timeoutNo ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 2Ip nat pool pool-name start-ip-addr end-ip-addr Netmask netmask prefix-length / prefix-lengthFrom previous Table C-8. NAT Commands 3Clear ip nat translation No ip dhcp pool pool-name Dhcp Server CommandsTable C-9. Dhcp Server Commands 1 No service dhcpDns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 2Default-router ip-address No default-router ip-address Domain-name domain-name No domain-name domain-nameNetwork network-num Table C-9. Dhcp Server Commands 3Example ip dhcp relay max-clients Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands No ip dhcp-server ip-addressNo access-list access-list-numpermit deny Filter access-list CommandsTable C-11. Filter Commands 1 Access-list access-list-num permit denyFor Extended IP Access Lists Table C-11. Filter Commands 2Example access-list 200 permit 0x200 range Table C-11. Filter Commands 3For Protocol Type Access Lists No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4Table C-12. Diagnostic Commands 1 Diagnostic CommandsTraceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2Show arp Show CommandsTable C-13. Show Commands 1 Show configurationShow interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 2Show configuration saved unsaved Show frame-relay mapShow ip route ip-address Table C-13. Show Commands 3Show ip dhcp binding ip-address Show ip nat translationsShow spanning-tree Table C-13. Show Commands 4Show ip traffic Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type CodesTable C-14. Ethernet Type Codes Hex 2 Description All 3 n = Destination unreachable Protocol and Port DesignationsIcmp Designations All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries ShortcutsIntf-type intf-num .sub-intf-num Show Command SummaryTable D-1. Show Commands Function Table D-2. Access Control and System Level Commands Function Access Control and System Level Command SummaryDns-serverip-address CLI Command SummaryTable D-3. CLI Commands 1 Clear counters intf-type intf-num .sub-intf-numEncapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2CLI Command Default Settings Rear Panels Connectors, Cables, and Pin AssignmentsConnectors, Cables, and Pin Assignments Model COM Port for 9126 and 9128-II 25-Position COM Port ConnectorSignal Direction Pin # Pin # Signal DirectionModular Plug DB9 Socket COM Port-to-PC Cable Feature No -F2-550COM Port for 9128-II Carrier Mount COM Port Non-Keyed PositionPosition Modular Plug DB25 Plug COM Port-to-Terminal/Printer Cable Feature No -F2-540COM Port Non-Keyed Cisco 2500 Series Router RJ45 Jack COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port AUX Port Signal DB25 Pin # Direction COM Port-to-Router Cables3COM Router DB9 Socket COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #COM Port AUX Port Signal RJ45 Pin # Direction COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # DTR RTS Gender Adapter/ChangerLAN Adapter Converter and Cable Plug-to-Modular Jack Converter Com Port Position DB25 PlugDirection Pin Socket DTE Port ConnectorPin Standard V.35 Straight-through CableStandard V.35 Crossover Cable MM NNPosition DB15 Modular Plug Socket Unkeyed DSX-1 ConnectorDSX-1 Adapter Feature No -F1-560 Function Circuit Direction Pin NumberDSX-1 Port for 1-Slot 9128-II 15-Position Function Circuit Line # Pin # T1 Network Cable Feature No -F1-500T1 Mass Termination Cable Feature No -F1-500 Plug Unkeyed Ethernet Port ConnectorCanadian T1 Line Interface Cable Feature No -F1-510 Isdn Modular Cable Modem ConnectorIsdn DBM Connector Connectors, Cables, and Pin Assignments September Physical Environment Table F-1. NAM Technical Specifications 1 CriteriaPhysical Dimensions ApprovalsTable F-1. NAM Technical Specifications 2 Criteria Ethernet Port Table F-1. NAM Technical Specifications 3 CriteriaIsdn PRI DBM Interface B8ZSPower Consumption Dissipation Ethernet Port FrameSaver Isdn BRI DBM InterfaceBRI, NI-1 Heat Dissipation Max AC Power RequirementsTypical Power Consumption Standards Compliance Switch CompatibilityService Supported Switched Network InterfaceLine Build-Out LBO Framing FormatCoding Format FrameSaver SLV Units Model/FeatureEquipment Description NumberEquipment List Isdn PRI DBM NMS Products FrameSaver SLM Feature Set UpgradeOptional Features Power SuppliesSeries Access Carrier 9128-II NAM only Cables Description Part Number Feature NumberIN-1 IndexCLI IN-2Becn Dhcp IN-3DBM IN-4EIR IN-5EER IN-6 IP SLV IN-7LAN LOS IN-8LOF NMS IN-9OID IN-10Port IN-11IN-12 IN-13 IN-14 IN-15 IN-16
Related manuals
Manual 32 pages 12.58 Kb
Top Page Image Contents