Paradyne 2600 IP DSLAM manual Connecting a Modem to the Console Port

Page 30

2. Cabling

Connecting a Modem to the Console Port

Procedure

To connect a modem to the CONSOLE port:

1.Determine and procure the proper DCE cable type for your modem. The CONSOLE port requires a DB9 plug connector. The other connector depends on the serial port on your modem, but normally a DB25 plug is required. The cable must be an EIA-232-E crossover (null modem) cable.

2.Connect the DB9 plug connector to the CONSOLE port socket.

3.If the modem will be permanently connected, fasten the connector to the Management Module with its captive screws. If the BitStorm 2600 is in a rack, dress the cable to the left and attach it to the rail with a cable tie.

4.Connect the other end of the cable to the serial port of your modem.

Serial Port

Modem

PWR

ALM TST

LINE

ETHERNET

PORT1-

 

 

 

10/100BT

PORT2-

 

 

 

10/100BT

1000BT

 

 

 

PORT3

 

 

LINK

ACT

 

 

ALARM

 

CONSOLE

Port

GigE

 

STATUS

ALARM

TEST

1

3

5

 

 

 

 

 

 

 

 

 

2

7

9

 

 

 

 

 

 

 

4

6

11

13

15

 

 

 

 

8

10

17

 

 

 

 

 

12

19

21

 

 

 

 

 

 

14

16

18

23

 

 

 

 

 

 

20

22

 

 

 

 

 

 

 

 

24

 

 

 

 

 

 

 

 

 

 

DSL PORTS 1-24

03-17448

2-8

January 2004

2600-A2-GN20-10

Image 30
Contents IP Dslam Copyright 2004 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Japan January Contents Equipment List Technical Specifications Index ConfigurationConnectors and Pin Assignments LEDsAbout This Guide Document Purpose and Intended AudienceDocument Summary Related Product Documents Document Number Document TitleInstallation OverviewInstallation Site PreparationCables Required DSL PortsPackage Contents Unpacking the HardwareFlat-head screw for attaching 19 mounting brackets to Mounting Configurations Installing the Brackets for Rack MountingMounting Brackets Inch 483 mm Rack Mount Installing the BitStorm 2600 Into a Rack 03-17436 Installing the BitStorm 2600 on a Wall 17.85 in 453 mm Installing the BitStorm 2600 on a Shelf or Desktop Cabling Cabling OverviewDSL Ports GigE Uplink Port 10/100BaseT Uplink Port Chaining BitStorm 2600s Management Port Connecting a Terminal or PC to the Console Port Console PortConnecting a Modem to the Console Port Alarm Interface Ground Connecting to Power Cabling January LEDs LED LocationsLED Meanings LEDConfiguration Conventions UsedUsing the CLI CLI Commands FunctionConfigure Management Inband Address BitStorm 2600 Startup Procedure LoginStartup Procedure for Inband Management Startup Procedure for Out-of-Band ManagementUsing the Web Interface Configuration / Management / Snmp System / UsersProcedure Connectors and Pin Assignments Figure A-1. BitStorm 2600 IP Front PanelDSL Ports and Pots Splitter Connectors Port 1 and Port 2 10/100BaseT Connectors Port 3 1000BaseT ConnectorPort 3 GigE SFP Connector Table A-4. Port 3 GigE Connector Signal PinConsole Port Connector Alarm Connector Table A-6. Alarm Connections Signal Direction ContactEquipment List Description Model NumberEquipment List Technical Specifications DSLTable C-1. BitStorm 2600 Technical Specifications 2 Criteria Index NumericsIN-2 IN-3 IN-4