Paradyne 6382 manual Static Connection Setup

Page 35

3. Using the Web Interface

To complete the connection you must now click the Apply button. The Apply button will temporarily save this connection. To make the change permanent, click on Tools (at the top of the page) and select System Commands. At the System Commands page, click on Save All.

Static Connection Setup

A static connection is used whenever a known static IP is assigned. The accompanying information such as the subnet mask and the default gateway should also be specified. Up to three Domain Name Server (DNS) addresses can also be specified. These servers give you access to other web servers. The valid range of IP addresses is 1.0.0.0 to 223.255.255.254.

To configure the router for a Static connection:

Procedure

1.Click on Setup and then click on New Connection. The default Static connection setup is displayed.

2.At the Type field, select Static. The Static Connection Setup page is displayed.

3.Give your Static connection a unique name. The name must not have spaces and cannot begin with numbers.

4.Optionally enable Network Address Translation (NAT) and the Firewall options. Firewall and NAT services must be enabled. See Firewall/NAT Services on page 3-21.

5.Select a PVC Sharing type of Disable, Enable, or VLAN.

6.Select or enter a VPI and VCI (as supplied by your DSL service provider or your ISP), or click in Auto PVC. (Auto PVC causes the router to perform automatic VPI/VCI detection as defined in DSL forum TR-068.) For VLAN, specify a VLAN ID and priority.

7.Select NAT and Firewall if you want them active for this connection. Firewall and NAT services must be enabled. See Firewall/NAT Services on page 3-21.

8.Select the encapsulation type (LLC or VC). If you are not sure which to use, just use the default mode.

9.Based upon the information your ISP provided, enter your assigned IP Address, Subnet Mask, Default Gateway (if provided), and Domain Name Services (DNS) address (if provided). Specify the VPI and VCI settings. Your DSL service provider or your ISP will supply these.

10.Select the quality of service (QOS). Leave the default value if your ISP did not provide this information.

11.Set the mode to Bridged or Routed as instructed by your ISP.

6382-A2-GB20-00

April 2005

3-11

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 6382 4-Port Router Copyright 2005 Paradyne Corporation All rights reserved Important Safety Instructions 6382-A2-GB20-00 Canada EMI Notice Japan Notices Contents Contents Index TroubleshootingTerminology Contents April Product-Related Documents About This GuideDocument Purpose and Intended Audience Document SummaryAbout This Guide April Definitions Features of the 6382 4-Port RouterIntroduction Ports and Buttons Back Panel System RequirementsPacking List LED Description Front PanelIntroduction April Overview Hardware Installation PC SetupConnecting the Hardware Hardware Installation Windows XP Configuring Your PC’s IP AddressAssigning an IP Address to your PC Automatically by Dhcp Network Connections in Windows XP TCP/IP Properties in Windows XP WindowsWindows ME Windows 95 Windows NT Logging Into Your Router Using the Web InterfaceQuick Start HomeQuick Start Dhcp Quick Start Static Saving Changes SetupWide Area Network Connection Local Area Network ConnectionConfiguring the WAN New Connection PPPoE Connection SetupPPPoE Connection Setup PPPoA Connection Setup PPPoA Connection Setup Static Connection Setup Static IP Connection Setup Dhcp Connection Setup10. Dhcp Connection Setup Bridged Connection 11. Bridged Connection SetupClip Connection Modify an Existing Connection 12. Clip Connection Setup13. Modem Setup Modem SetupEnable/Disable Dhcp Configuring the LANChanging the Routers IP address 15. Ethernet Switch Ethernet Switch16. Firewall/NAT Services Firewall/NAT ServicesUPnP AdvancedSntp Snmp Port Forwarding IP QoS21. Port Forwarding Netmeeting 22. IP Filters IP FiltersVlan LAN Clients24. Vlan Bridge Filters25. Bridge Filters 26. Multicast MulticastStatic Routing Igmp Snooping28. Static Routing Dynamic Routing29. Dynamic Routing Log Out Access ControlRemote Log System CommandsTools Severity Levels Description 32. Remote Log User Management33. User Management Update GatewayAnalyzer 34. Update Gateway36. Ping Test Ping Test37. Modem Test Modem Test38. Network Statistics Status39. Modem Status Router Is Not Functional TroubleshootingStatus LED is Always Off You Cannot Connect to the RouterLEDs Blink in a Sequential Pattern Status LED Continues to BlinkTerminology What is a Firewall?What is NAT? What is a DMZ?What is a Router? Dhcp IndexIN-2 IN-3 IN-4
Top Page Image Contents