Patton electronic manual Web GUI, Model 3101RC Getting Started Guide3 Configuration

Page 23

Model 3101RC Getting Started Guide3 • Configuration

local:%configure

local:(conf)#runningcfg write partition 1

Are you sure write running configuration to Flash ROM partition #1 ? (Y/[N])y System writing Flash ROM partition #1...

Write running configuration to Flash ROM partition #1 success! local:(conf)#exit

local:%ping 172.16.10.72

PING 172.16.10.72 (172.16.10.72): 56 data bytes

64 bytes from 172.16.10.72: icmp_seq=0 ttl=64 time=8.7 ms

64 bytes from 172.16.10.72: icmp_seq=1 ttl=64 time=0.8 ms

64 bytes from 172.16.10.72: icmp_seq=2 ttl=64 time=0.8 ms

64 bytes from 172.16.10.72: icmp_seq=3 ttl=64 time=0.8 ms

--- 172.16.10.72 ping statistics ---

4 packets transmitted, 4 packets received, 0% packet loss round-trip min/avg/max = 0.8/2.7/8.7 ms

local:%

Now you can access the Model 3101 via Telnet on port 23 (for using CLI) or Web GUI interface by entering the IP address of 3101 in your browser's URL/address ﬁeld.

Web GUI

Use the following commands to provision an IP port in the Web GUI:

1.On the menu tree, click on System > Board Setup. The Board Setup page is displayed.

Figure 10. Board IP Setup

2.Type in new IP setting in the GBE (In Band) section for in-band IP provisioning.

3.Type in new IP setting in the MGMT (Out Band) section for out-band IP provisioning.

4.Click on Modify to submit the modiﬁcation.

Provisioning a Management IP Port

23

Image 23

Contents ADSL2/2+ Triple-Play Access Ipdslam Module Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information List of Figures List of Tables Structure About this guideAudience Safety when working with electricity PrecautionsMouse conventions Typographical conventions used in this documentGeneral conventions Model 3101RC Overview Chapter contentsIntroduction Model 3101RC ADSL2/2+ Triple-play Access Ipdslam ModuleApplications FeaturesHardware Installation Electrostatic Discharge Protection Pre-InstallationSafety Requirement Tools and Test Equipment RequirementsConnecting the ADSLx interfaces Hardware InstallationRJ-45 Electrical Trunk Port Connecting the GBE trunk interfaceEthernet Port RJ-45 pin assignment Ethernet Port 10/100 Enet on Trunk CardTxD Console Port ConfigConﬁguration CLI Provisioning a Management IP PortConﬁgure Web GUI Model 3101RC Getting Started Guide3 ConfigurationIP Routes Example Conﬁguration Import/ExportExport export ﬁle from Running conﬁg to the Tftp server Database conﬁguration menuin the Web GUI Import File Write Download Conﬁg To FlashWrite downloaded Conﬁg to Flash in progress Load Remote Conﬁg to Running Conﬁg Get File Import File Load Remote Conﬁg to Running ConﬁgPut Running Conﬁg to Remote Tftp Server Put File Export File Put Running Conﬁg to Remote Tftp ServerSave Running Conﬁg to Flash Write Running Conﬁguration Save Running Conﬁg to Flash System ConﬁgLoad Flash to Running Conﬁg Load Conﬁguration Reload Flash to Running ConﬁgRestore Factory Default Restore Factory DefaultFlash Boot Point Conﬁguration Select Flash Boot Point Conﬁguration Selectﬁrmware login 172.16.100.41 username Firmware UpdateFTP Get In Progress Firmware update no actionFirmware Write Successful Firmware Write In ProgressOperation Tools and Equipment Requirements Maintenance RequirementDispatching Maintenance Personnel Routine Maintenance3101RC LEDs Controls and LED IndicationConfig TM Controls and LED Indication 3101TM LEDsContacting Patton for assistance Returns for credit Warranty coverageOut-of-warranty service Contact informationShipping instructions Return for credit policyRMA numbers Appendix a Compliance information EMC Compliance Safety ComplianceCompliance CE Declaration of Conformity