Patton electronic Model 3101RC manual Provisioning a Management IP Port, Cli

Page 21

Model 3101RC Getting Started Guide	3 • Configuration

Provisioning a Management IP Port

This section describes how to use CLI commands or Web GUI to provision an IP port for the Model 3101.

Referring to the previous section, use a console cable to connect a host PC and the Model 3101 through its console port (CONFIG). Then on PC run the terminal program with the setting shown below:

Figure 9. Terminal program settings

Note For both CLI and Web Conﬁguration Tool, the default login user- name and password are: admin/admin.

CLI

In the PC terminal screen, type in the login user name and password to login the system. Type the following command to check current IP setting of all the management ports.

Command	Explanation

enable	Enter enable command mode.

show management all	Display all system management port IP settings.

LOCAL login: admin

Password:

this is motd file to inform any information to user

PATTON

System Description:3101 48-port ADSL2+ POTS Hardware Version:A

Firmware Version:0.74B03

Software Version:0.74B03

Compiled Wed Oct 24 16:41:23 CST 2007 local:>enable

local:%show management all

GBEMGMT

------------------------------------------------

IP Address :192.168.100.1	192.168.1.1
Network mask :255.255.255.0	255.255.255.0
Default route:--	--
local:>

Provisioning a Management IP Port

21

Image 21

Contents ADSL2/2+ Triple-Play Access Ipdslam Module Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information List of Figures List of Tables About this guide AudienceStructure Safety when working with electricity PrecautionsTypographical conventions used in this document General conventionsMouse conventions Model 3101RC Overview Chapter contentsIntroduction Model 3101RC ADSL2/2+ Triple-play Access Ipdslam ModuleApplications FeaturesHardware Installation Safety Requirement Pre-InstallationTools and Test Equipment Requirements Electrostatic Discharge ProtectionConnecting the ADSLx interfaces Hardware InstallationRJ-45 Electrical Trunk Port Connecting the GBE trunk interfaceEthernet Port RJ-45 pin assignment Ethernet Port 10/100 Enet on Trunk CardTxD Console Port ConfigConﬁguration CLI Provisioning a Management IP PortConﬁgure Web GUI Model 3101RC Getting Started Guide3 ConfigurationIP Routes Example Conﬁguration Import/ExportExport export ﬁle from Running conﬁg to the Tftp server Database conﬁguration menuin the Web GUI Import File Write Download Conﬁg To FlashWrite downloaded Conﬁg to Flash in progress Load Remote Conﬁg to Running Conﬁg Get File Import File Load Remote Conﬁg to Running ConﬁgPut Running Conﬁg to Remote Tftp Server Put File Export File Put Running Conﬁg to Remote Tftp ServerSave Running Conﬁg to Flash Write Running Conﬁguration Save Running Conﬁg to Flash System ConﬁgLoad Flash to Running Conﬁg Load Conﬁguration Reload Flash to Running ConﬁgRestore Factory Default Restore Factory DefaultFlash Boot Point Conﬁguration Select Flash Boot Point Conﬁguration Selectﬁrmware login 172.16.100.41 username Firmware UpdateFTP Get In Progress Firmware update no actionFirmware Write Successful Firmware Write In ProgressOperation Dispatching Maintenance Personnel Maintenance RequirementRoutine Maintenance Tools and Equipment Requirements3101RC LEDs Controls and LED IndicationConfig TM Controls and LED Indication 3101TM LEDsContacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditReturn for credit policy RMA numbersShipping instructions Appendix a Compliance information Compliance Safety ComplianceCE Declaration of Conformity EMC Compliance