Patton electronic Model 3101RC manual Configure

Page 22

Model 3101RC Getting Started Guide

3 • Configuration

 

 

Then, type the following commands to change in-band or out-band IP settings as you want:

Command

Explanation

 

 

configure

Enter configure command mode.

 

 

management gbe <ipv4 address>

Set in-band management port IP setting.

[netmask <netmask>]

 

 

 

management gbe vlan <vlan id>

Restrict incoming VLAN tag of in-band manage-

 

ment. This setting is optional not mandatory.

 

 

management mgmt <ipv4 address>

Set out-band management port IP setting.

[netmask <netmask>]

 

 

 

route default <ipv4 address>

Set system default gateway.

 

 

route <destination ip> netmask <netmask>

Add other routes in the route table (option).

gateway <gateway ip>

 

 

 

exit

Go back to enable command mode.

 

 

show management all

Check if the inband and outband IP settings have

 

been changed.

 

 

show route

Display system route table.

 

 

configure

Enter configure command again.

 

 

runningcfg write partition <number>

Save new setting to memory (partition 1 or 2).

 

 

After setting the in-band/out-band IP of the Model 3101, remember to connect the 3101RC's 10/100 Ether- net port to the Ethernet LAN. Then in the previous PC terminal screen, type the following commands to ver- ify if the Ethernet connection between the management station and the Model 3101 is working.

Command

Explanation

 

 

exit

Go back to enable command mode.

 

 

ping <ipv4 address>

Ping to the management station to verify the con-

 

nection is working.

 

 

local:%configure

local:(conf)#management gbe 192.168.100.5 netmask 255.255.255.0 local:(conf)#management gbe vlan 5 local:(conf)#management mgmt 172.16.10.81 netmask 255.255.255.0 local:(conf)#route default 172.16.10.254

local:(conf)#route 192.168.5.0 netmask 255.255.255.0 gateway 172.16.10.251

local:(conf)#exit

 

local:%show management all

 

GBE

MGMT

------------------------------------------------

IP Address :192.168.100.5

172.16.10.81

Network mask :255.255.255.0

255.255.255.0

Default route:--

172.16.10.254

local:%show route

 

 

Default Route : 172.16.10.254

 

No IP Address

Netmask

Gateway

-----------------------------------------------------

01

192.168.5.0

255.255.255.0

172.16.10.251

Provisioning a Management IP Port

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents ADSL2/2+ Triple-Play Access Ipdslam Module Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information List of Figures List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentMouse conventions Chapter contents Model 3101RC OverviewModel 3101RC ADSL2/2+ Triple-play Access Ipdslam Module IntroductionFeatures ApplicationsHardware Installation Tools and Test Equipment Requirements Pre-InstallationSafety Requirement Electrostatic Discharge ProtectionHardware Installation Connecting the ADSLx interfacesConnecting the GBE trunk interface RJ-45 Electrical Trunk PortEthernet Port 10/100 Enet on Trunk Card Ethernet Port RJ-45 pin assignmentConsole Port Config TxDConfiguration Provisioning a Management IP Port CLIConfigure Model 3101RC Getting Started Guide3 Configuration Web GUIIP Routes Configuration Import/Export ExampleExport export file from Running config to the Tftp server Import File Write Download Config To Flash Database configuration menuin the Web GUIWrite downloaded Config to Flash in progress Import File Load Remote Config to Running Config Load Remote Config to Running Config Get FileExport File Put Running Config to Remote Tftp Server Put Running Config to Remote Tftp Server Put FileSave Running Config to Flash System Config Save Running Config to Flash Write Running ConfigurationReload Flash to Running Config Load Flash to Running Config Load ConfigurationRestore Factory Default Restore Factory DefaultFlash Boot Point Configuration Select Flash Boot Point Configuration SelectFirmware Update firmware login 172.16.100.41 usernameFirmware update no action FTP Get In ProgressFirmware Write In Progress Firmware Write SuccessfulOperation Routine Maintenance Maintenance RequirementDispatching Maintenance Personnel Tools and Equipment RequirementsControls and LED Indication 3101RC LEDsConfig 3101TM LEDs TM Controls and LED IndicationContacting Patton for assistance Contact information Warranty coverageOut-of-warranty service Returns for creditRMA numbers Return for credit policyShipping instructions Appendix a Compliance information CE Declaration of Conformity Safety ComplianceCompliance EMC Compliance
Top Page Image Contents