Patton electronic 3196RC user manual LED display, Ethernet LED CLK Source LED CLK Error LED

Page 21

Model 3196RC T-DAC User Manual	1 • Introduction

POWER LED

RC T-DACncentrator

CPU LED

SYSTEM LED

ALARM LED

POWER
CPU	FAIL

ALARM

ETHERNET LED

CLK SOURCE LED

CLK ERROR LED

TEST MODE LED WAN LED

	SYSTEM
	ETHERNET
	CLK	SOURCE
	CLK
		ERROR

	TEST		MODE
	WAN

	9	1
DSL CONNECTION LEDs	1011	2 3	DSL
	121314	4 5 6	CONNECTION
	15	7
	16	8
	10/100 ENET
	CONFIG
		READY

Figure 4. Model 3196RC front panel LEDs

10/100 ENET

port

CONFIG

port

READY

LED

LED display

Front panel LEDs (figure 3) display the status of the WAN ports, the iDSL ports, the Ethernet LAN port, power, and the alarms. The LEDs are described in table 3.

			Table 3. LED definitions

LED	Color	Status	Meaning

POWER	Green	On solid	Power is being applied. No action recommended.
		Flashing	The 3196RC has detected a power failure on a power bus.

		Off	No input power is being applied.
CPU FAIL	Red	On solid	CPU is unable to load the software from FLASH to RAM for operation.

		Off	The CPU is operating normally.
ALARM	Yellow	On solid	A minor alarm condition has been detected.

		Flashing	A major alarm condition has been detected.
		Off	The Model 3196RC is operating normally.
SYSTEM	Green	Flashing	The Model 3196RC is operating normally.
		Off	The Model 3196RC is not functioning properly.

ETHERNET	Green	On solid	Link status is nominal for the Ethernet port. No action recommended.
		Off	A valid link has not been detected.

Hardware overview

21

Image 21

Contents IDSL TDM-Digital Access Concentrator T-DAC Mailsupport@patton.com Summary Table of Contents Table of Contents Operation and shutdown Network Ports RJ-21X connector pin-out List of Figures Page List of Tables Radio and TV Interference Compliance InformationFCC Part 68 Acta Statement Industry Canada NoticeCE Notice About this guide AudienceStructure Precautions Typographical conventions used in this documentGeneral conventions Garamond bold type Mouse conventionsIntroduction Chapter contentsModel 3196RC T-DAC Model 3196RC iDSL T-DAC overviewWAN Hardware overviewRS-232 control port Power systemCentral processing unit IDSL portsPhysical dimensions TemperatureManagement services System timingLED display Ethernet LED CLK Source LED CLK Error LEDDSL Approvals Hardware installation DAC blades installation IntroductionUnpacking the Model 3196RC T-DAC Alignment/ESD pin and card handle Connecting the Ethernet ports Cable installationDB-9-to-RJ-45 cable diagram WAN cable‘s 68-pin Scsi connector Connecting to the T1/E1 WAN portsNot Used RJ-21X connector Connecting the iDSL ports2.2 Vpp Connecting the Bits clockEXT Clock connector location Completing the hardware installation Configuring the T-DAC for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Displaying the T-DAC 3196RC web administration pages Using a browser to complete Model 3196RC configurationHome page overview RC Configuration Menu homeHome page window panes Flash Configuring the default gatewayIP Routing Information window Configuring the system clocking parametersExample For Clock Reference select slave3 Configuring the DS0 mappingDacs Display Type drop-down menu , select displayLongForm0 Solution Examples for configuring static connectionsIDSL Port Configuration IDSL Port 1 Details Click the iDSL hyperlink on the 3196RC Configuration Menu Click on Submit Query Activating the iDSL ports IDSL Port Configuration windowConfiguring the T-DAC for operation Configuring the T-DAC for operation Accessing the Line Interface Settings Configuring line settings and signaling for E1T1/E1 Link Activity Ports 1 4 Configuring the E1 line interface settingsFrom the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 Line Type pull-down menu with dsx1ESF2 selected Configuring the T1 line settingsFrom the Line Build Out pull-down menu select t1pulse0dB1 Backing up your configuration parameters Saving your configurationIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown De-activating the Model 3196RC Activating the Model 3196RCRemote loop Troubleshooting and maintenanceCited in section De-activating the Model 3196RC on Power Fault analysisSystem Basic iDSL and T1/E1 test modes IDSL port test modesLocal loop Local loopback Remote loopLine Loopback Line LoopDSX1 payload loop dsx1PayloadLoop T1/E1 port test modesPeriodic maintenance DSX1 line loop dsxLineLoopCalibration Maintenance Exporting the current Model 3196RC configurationReplacing the Model 3196RC IMPORT/EXPORT Troubleshooting and maintenance Removing the defective Model 3196RC Importing a saved configuration Installing the replacement Model 3196RCCompleting the installation Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditReturn for credit policy RMA numbersShipping instructions Appendix a Network Ports RJ-21X connector pin-out DSL Port Pin Positions Wire Color Code Port Appendix B WAN Network Module Connector pinout Pin Telco pinout Port Pairs 68 Pin Wire Color Direction Positions CodePort 13/RX Pink/Violet Violet/Pink Port 14/TX