Patton electronic Installing the replacement Model 3196RC, Importing a saved configuration

Page 83

Model 3196RC T-DAC User Manual

5 • Troubleshooting and maintenance

 

 

3.Unlock the handles by pressing the red button on each handle. The button immediately activates the switch (turning it to an open position), while the button itself remains depressed. The blade can then be removed.

4.Remove the malfunctioning Model 3196RC by pushing the handles outwards, pulling the card gently but firmly from its slot in the chassis. Place the removed card in the container the replacement Model 3196RC came in so you can return the defective Model 3196RC for repair.

Installing the replacement Model 3196RC

1.Insert the replacement Model 3196RC into the rack chassis.

2.Insert the rear blade into the desired slot in the rack chassis. Make sure the blade is seated properly in the slot guides.

3.Gently press the blade into the chassis until the alignment/ESD pin engages the chassis. When the blade is fully seated, the red buttons in the handles click up automatically, thus locking the handle and activating the switch (closed position). The click of the button gives a visual and audible confirmation that the board is fully seated.

4.Connect the following cables to the Model 3196RC:

The T1/E1 WAN cable (68-pin SCSI connector)

The iDSL modem cable (RJ-21X connector)

The RS-232 CONFIG cable

The 10/100 ETHERNET cable

5.Verify that the green POWER LED is lit.

Importing a saved configuration

Before importing a saved configuration, you must define the Model 3196RC’s IP address and netmask. These parameters are defined via the Model 3196RC RS-232 CONFIG port on the Model 3196RC.

1.Refer to Chapter 3, “Configuring the T-DAC for operation” and follow the procedures contained in sec- tion “Initial configuration through the RS-232 control port” on page 37.

2.To import a saved configuration, connect your Web browser to the Administration Pages, then click on Import/Export under the Configuration Menu to display the Import/Export page (figure 57 on page 80).

3.To import a configuration file into the Model 3196RC, type the complete path and filename for the con- figuration file you wish to load or click on the Browse… button to select the desired file, then click the Submit Query button.

Upon successfully importing the file, the Model 3196RC will display Configuration Load Complete, indi- cating that the new operating parameters have been loaded into flash memory.

4.On the Configuration Menu, click the HOME hyperlink, then click the Hard Reset button under Imme- diate Actions.

Note Do not select Record Current Configuration after importing config- uration parameters.

Maintenance

83

Image 83
Contents IDSL TDM-Digital Access Concentrator T-DAC Mailsupport@patton.com Summary Table of Contents Table of Contents Operation and shutdown Network Ports RJ-21X connector pin-out List of Figures Page List of Tables Radio and TV Interference Compliance InformationFCC Part 68 Acta Statement Industry Canada NoticeCE Notice Structure About this guideAudience General conventions PrecautionsTypographical conventions used in this document Garamond bold type Mouse conventionsIntroduction Chapter contentsModel 3196RC T-DAC Model 3196RC iDSL T-DAC overviewWAN Hardware overviewIDSL ports Power systemRS-232 control port Central processing unitSystem timing TemperaturePhysical dimensions Management servicesLED display Ethernet LED CLK Source LED CLK Error LEDDSL Approvals Hardware installation Unpacking the Model 3196RC T-DAC DAC blades installationIntroduction Alignment/ESD pin and card handle Connecting the Ethernet ports Cable installationDB-9-to-RJ-45 cable diagram WAN cable‘s 68-pin Scsi connector Connecting to the T1/E1 WAN portsNot Used RJ-21X connector Connecting the iDSL ports2.2 Vpp Connecting the Bits clockEXT Clock connector location Completing the hardware installation Configuring the T-DAC for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Displaying the T-DAC 3196RC web administration pages Using a browser to complete Model 3196RC configurationHome page overview RC Configuration Menu homeHome page window panes Flash Configuring the default gatewayIP Routing Information window Configuring the system clocking parametersExample For Clock Reference select slave3 Configuring the DS0 mappingDacs Display Type drop-down menu , select displayLongForm0 Solution Examples for configuring static connectionsIDSL Port Configuration IDSL Port 1 Details Click the iDSL hyperlink on the 3196RC Configuration Menu Click on Submit Query Activating the iDSL ports IDSL Port Configuration windowConfiguring the T-DAC for operation Configuring the T-DAC for operation Accessing the Line Interface Settings Configuring line settings and signaling for E1T1/E1 Link Activity Ports 1 4 Configuring the E1 line interface settingsFrom the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 Line Type pull-down menu with dsx1ESF2 selected Configuring the T1 line settingsFrom the Line Build Out pull-down menu select t1pulse0dB1 Backing up your configuration parameters Saving your configurationIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown De-activating the Model 3196RC Activating the Model 3196RCRemote loop Troubleshooting and maintenanceCited in section De-activating the Model 3196RC on Power Fault analysisSystem Local loop Basic iDSL and T1/E1 test modesIDSL port test modes Local loopback Remote loopLine Loopback Line LoopDSX1 payload loop dsx1PayloadLoop T1/E1 port test modesCalibration Periodic maintenanceDSX1 line loop dsxLineLoop Replacing the Model 3196RC MaintenanceExporting the current Model 3196RC configuration IMPORT/EXPORT Troubleshooting and maintenance Removing the defective Model 3196RC Importing a saved configuration Installing the replacement Model 3196RCCompleting the installation Contacting Patton for assistance Returns for credit Warranty coverageOut-of-warranty service Contact informationShipping instructions Return for credit policyRMA numbers Appendix a Network Ports RJ-21X connector pin-out DSL Port Pin Positions Wire Color Code Port Appendix B WAN Network Module Connector pinout Pin Telco pinout Port Pairs 68 Pin Wire Color Direction Positions CodePort 13/RX Pink/Violet Violet/Pink Port 14/TX