Patton electronic 3196RC Connecting to the T1/E1 WAN ports, WAN cable‘s 68-pin Scsi connector

Page 29

Model 3196RC T-DAC User Manual	2 • Hardware installation

Connecting to the T1/E1 WAN ports

An active T1/E1 is not necessary to configure the T-DAC. However, an active T1/E1 connection is required when mapping iDSL modems to specific time slots in the T1/E1 ports or even for mapping WAN time slots to other WAN time slots. The factory-set default configuration of the Model 3196RC has the T1/E1 ports disabled.

Note The cable connecting the T1/E1 WAN ports to the RJ-48C termina- tion jack should be CAT-3 or higher and extend no farther than

1 mile (1.6 km) from the digital services termination.

AMP 749621-7 (or equivalent)

Pin 1

34

35

68

Figure 10. WAN cable‘s 68-pin SCSI connector

1.Connect the 68-pin SCSI connector (see figure 10) of the 6-foot WAN cable (see figure 11) to the connec- tor on the rear panel of the Model 3196RC

Figure 11. 68 pin SCSI-to-RJ45 6-foot WAN cable

Cable installation

29

Image 29

Contents IDSL TDM-Digital Access Concentrator T-DAC Mailsupport@patton.com Summary Table of Contents Table of Contents Operation and shutdown Network Ports RJ-21X connector pin-out List of Figures Page List of Tables Radio and TV Interference Compliance InformationFCC Part 68 Acta Statement Industry Canada NoticeCE Notice Structure About this guideAudience General conventions PrecautionsTypographical conventions used in this document Garamond bold type Mouse conventionsIntroduction Chapter contentsModel 3196RC T-DAC Model 3196RC iDSL T-DAC overviewWAN Hardware overviewRS-232 control port Power systemCentral processing unit IDSL portsPhysical dimensions TemperatureManagement services System timingLED display Ethernet LED CLK Source LED CLK Error LEDDSL Approvals Hardware installation Unpacking the Model 3196RC T-DAC DAC blades installationIntroduction Alignment/ESD pin and card handle Connecting the Ethernet ports Cable installationDB-9-to-RJ-45 cable diagram WAN cable‘s 68-pin Scsi connector Connecting to the T1/E1 WAN portsNot Used RJ-21X connector Connecting the iDSL ports2.2 Vpp Connecting the Bits clockEXT Clock connector location Completing the hardware installation Configuring the T-DAC for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Displaying the T-DAC 3196RC web administration pages Using a browser to complete Model 3196RC configurationHome page overview RC Configuration Menu homeHome page window panes Flash Configuring the default gatewayIP Routing Information window Configuring the system clocking parametersExample For Clock Reference select slave3 Configuring the DS0 mappingDacs Display Type drop-down menu , select displayLongForm0 Solution Examples for configuring static connectionsIDSL Port Configuration IDSL Port 1 Details Click the iDSL hyperlink on the 3196RC Configuration Menu Click on Submit Query Activating the iDSL ports IDSL Port Configuration windowConfiguring the T-DAC for operation Configuring the T-DAC for operation Accessing the Line Interface Settings Configuring line settings and signaling for E1T1/E1 Link Activity Ports 1 4 Configuring the E1 line interface settingsFrom the Line Build Out pull-down menu select e1pulse1 Configuring line settings and signaling for T1 Line Type pull-down menu with dsx1ESF2 selected Configuring the T1 line settingsFrom the Line Build Out pull-down menu select t1pulse0dB1 Backing up your configuration parameters Saving your configurationIMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown De-activating the Model 3196RC Activating the Model 3196RCRemote loop Troubleshooting and maintenanceCited in section De-activating the Model 3196RC on Power Fault analysisSystem Local loop Basic iDSL and T1/E1 test modesIDSL port test modes Local loopback Remote loopLine Loopback Line LoopDSX1 payload loop dsx1PayloadLoop T1/E1 port test modesCalibration Periodic maintenanceDSX1 line loop dsxLineLoop Replacing the Model 3196RC MaintenanceExporting the current Model 3196RC configuration IMPORT/EXPORT Troubleshooting and maintenance Removing the defective Model 3196RC Importing a saved configuration Installing the replacement Model 3196RCCompleting the installation Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditShipping instructions Return for credit policyRMA numbers Appendix a Network Ports RJ-21X connector pin-out DSL Port Pin Positions Wire Color Code Port Appendix B WAN Network Module Connector pinout Pin Telco pinout Port Pairs 68 Pin Wire Color Direction Positions CodePort 13/RX Pink/Violet Violet/Pink Port 14/TX