Patton electronic 2635 General Characteristics, Ethernet, Sync Serial Interface, T1/E1 Interface

Page 119

Models 2603, 2621, and 2635 Getting Started Guide	B • Specifications

General Characteristics

•Compact low-cost router/bridge

•10/100 Ethernet

•Unlimited host support.

•Comprehensive hardware diagnostics, works with any operating system, easy maintenance and effortless installation.

•Built-in web conﬁguration.

•Setup allows for standard IP address and unique method for entering an IP address and mask WITHOUT use of a console connection. Default IP address of 192.168.200.10/24.

•Simple software upgrade using FTP into FLASH memory.

•Front panel LEDs indicate Power, WAN, Ethernet LAN speed and status.

•Field Factory Default Option.

•Standard 1 year warranty.

Ethernet

•Auto-sensing Full-Duplex 10Base-T/100Base-TX Ethernet.

•Standard RJ-45 and built-in MDI-X cross-over switch.

•IEEE 8021.d transparent learning bridge up to 1,024 addresses.

•8 IP address/subnets on Ethernet interface.

Sync Serial Interface

•ITU-T X.21 or V.35 interface

•Available with female DB-25 and DB-15 connectors

•User conﬁgurable DTE/DCE for X.21

T1/E1 Interface

•Line Rate 1.544 Mbps (T1), and 2.048 Mbps (E1)

•RJ-48C connector ( also includes dual BNC for E1 connections)

•DSX-1 levels for connection to local T1/E1 device (PBX).

•Nx56/64 kbps with full DS0 mapping

•AMI/B8ZS (T1), AMI/HDB3 (E1)

•ESF coding and framing (T1)

General Characteristics

119

Image 119

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General observations Factory default parametersGeneral conventions Typographical conventions used in this documentGeneral Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewWAN Interfaces EthernetProtocol support PPP SupportFront Panel Status LEDs and Console Port Logging or Smtp on events POST, Post errors, PPP/DHCP, IPSecurity On the rear panel from left to right are the following Rear panel connectors and switchesConsole port Ethernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Conﬁguration What you will need Hardware installationInterface cable installation RJ-48C pinout diagram Initial Configuration Ethernet connector Interface connector RJ-45 DB-15 Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cablePC Conﬁguration IP address modiﬁcationIP address has now been successfully changed Web Operation and ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Variables WAN Serial Port ConﬁgurationSerial Interface T1/E1 Interface Conﬁguration Web Interface ConﬁgurationWeb Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 OperationConﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services PPP Bridged WAN Service ConﬁgurationPPP Conﬁguration Leave User name and Password blank. Click on Create Remote site conﬁguration PPP RoutedPPP Routed Conﬁguration menu Click on CreateEdit IP address of WAN port Click the Update buttonPPP link status LMI Conﬁguration Username blank Password blank Click on the Create buttonLMI Management Frame Relay links Web Conﬁguration Methods Dlci Number Use Frame Relay ConﬁgurationFrame Relay bridged creation Frame Relay bridgedCentral site conﬁguration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed conﬁguration IP route for Frame Relay routed application Cost Interface frame-0WAN Services Security Conﬁguring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfacesSecurity conﬁguration home Click on the hyperlink New Policy... See ﬁgure Conﬁguring Security PoliciesDeleting a security Policy Enabling the FirewallFirewall Portﬁlters You can now ping between the two networks Security TriggersConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Global address pool and reserved map Introduction to NATEnabling NAT Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnetNext section see ﬁgure 58. has three parameters IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolConﬁguration of the Dhcp Relay Default gateway option informationAdditional option information Dhcp RelayDhcp Relay webpage Conﬁguring the DNS Relay DNS RelayDNS Relay conﬁguration webpage IP Services CLI Conﬁguration IP ServicesNext command disables the WEB server WEB ServerAssociated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser AuthenticationAccess the conﬁguration and status of the alarms AlarmAlarm & Alarm Error Log conﬁguration Remote AccessSave UpdateBackup/Restore Restart Website SettingsSnmp Daemon Error LogSnmp Daemon conﬁguration System ToolsSntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration ParametersSntp Client General Conﬁguration Parameters System Clock SettingConﬁguration of the internal system calendar clock System Status Port Connection Status System StatusHardware Status LAN StatusMAC address the MAC address of the Ethernet port WAN StatusStatus LEDs Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceReturns for credit Return for credit policyEMC Appendix a Compliance informationFCC Part 68 Acta Statement Model 2603 only ComplianceRadio and TV Interference FCC Part CE Declaration of ConformityIndustry Canada Notice 2603 Model only Appendix B Speciﬁcations T1/E1 Interface General CharacteristicsEthernet Sync Serial InterfaceManagement Protocol SupportPPP Support VDC power supply DimensionsPower and Power Supply Speciﬁcations AC universal power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 Assuming the MDI-X switch is in the out positionRJ-45 shielded 10/100 Ethernet port Serial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation Local VT-100 emulation Using the ConsoleCLI Terminology Produces a list of numbered transport objectsThen Another example shows when the user must provide a parameterAdding new users Administering user accountsSetting user passwords Enter the new password twice as promptedFor example, to change the security level for fred, enter Changing user settingsControlling login access Controlling user access

Related manuals

Manual 133 pages 54.65 Kb