Patton electronic 2635, 2621 manual Ethernet Cable, Adapter

Page 123

Models 2603, 2621, and 2635 Getting Started Guide	C • Cable Recommendations

Ethernet Cable

Ethernet cable (P/N 10-2500) (refer to “RJ-45 shielded 10/100 Ethernet port” on page 125)

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

Adapter

EIA-561 to DB-9 (P/N 16F-561) (refer to “RJ-45non-shieldedRS-232 console port (EIA-561)”on page 125)

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

Ethernet Cable

123

Image 123

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables About this guide AudienceStructure Precautions Safety when working with electricityImpaired functioning General observations Factory default parametersGeneral conventions Typographical conventions used in this documentGeneral Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewWAN Interfaces EthernetProtocol support PPP SupportLogging or Smtp on events POST, Post errors, PPP/DHCP, IP SecurityFront Panel Status LEDs and Console Port Rear panel connectors and switches Console portOn the rear panel from left to right are the following Ethernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Conﬁguration Hardware installation Interface cable installationWhat you will need RJ-48C pinout diagram Initial Configuration Ethernet connector Interface connector RJ-45 DB-15 Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cablePC Conﬁguration IP address modiﬁcationIP address has now been successfully changed Web Operation and ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration WAN Serial Port Conﬁguration Serial InterfaceVariables T1/E1 Interface Conﬁguration Web Interface ConﬁgurationWeb Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 OperationConﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services WAN Service Conﬁguration PPP ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP RoutedPPP Routed Conﬁguration menu Click on CreateEdit IP address of WAN port Click the Update buttonPPP link status Username blank Password blank Click on the Create button LMI Management Frame Relay linksLMI Conﬁguration Web Conﬁguration Methods Dlci Number Use Frame Relay ConﬁgurationFrame Relay bridged creation Frame Relay bridgedCentral site conﬁguration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed conﬁguration IP route for Frame Relay routed application Cost Interface frame-0WAN Services Security Conﬁguring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfacesSecurity conﬁguration home Click on the hyperlink New Policy... See ﬁgure Conﬁguring Security PoliciesEnabling the Firewall Firewall PortﬁltersDeleting a security Policy You can now ping between the two networks Security TriggersConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Introduction to NAT Enabling NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnetNext section see ﬁgure 58. has three parameters IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolConﬁguration of the Dhcp Relay Default gateway option informationAdditional option information Dhcp RelayDhcp Relay webpage Conﬁguring the DNS Relay DNS RelayDNS Relay conﬁguration webpage IP Services CLI Conﬁguration IP ServicesNext command disables the WEB server WEB ServerAssociated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser AuthenticationAccess the conﬁguration and status of the alarms AlarmAlarm & Alarm Error Log conﬁguration Remote AccessUpdate Backup/RestoreSave Restart Website SettingsSnmp Daemon Error LogSnmp Daemon conﬁguration System ToolsSntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration ParametersSntp Client General Conﬁguration Parameters System Clock SettingConﬁguration of the internal system calendar clock System Status Port Connection Status System StatusHardware Status LAN StatusMAC address the MAC address of the Ethernet port WAN StatusStatus LEDs Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceReturns for credit Return for credit policyEMC Appendix a Compliance informationFCC Part 68 Acta Statement Model 2603 only ComplianceRadio and TV Interference FCC Part CE Declaration of ConformityIndustry Canada Notice 2603 Model only Appendix B Speciﬁcations T1/E1 Interface General CharacteristicsEthernet Sync Serial InterfaceProtocol Support PPP SupportManagement VDC power supply DimensionsPower and Power Supply Speciﬁcations AC universal power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors Assuming the MDI-X switch is in the out position RJ-45 shielded 10/100 Ethernet portRJ-45 non-shielded RS-232 console port EIA-561 Serial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation Local VT-100 emulation Using the ConsoleCLI Terminology Produces a list of numbered transport objectsThen Another example shows when the user must provide a parameterAdding new users Administering user accountsSetting user passwords Enter the new password twice as promptedFor example, to change the security level for fred, enter Changing user settingsControlling login access Controlling user access

Related manuals

Manual 133 pages 54.65 Kb