Patton electronic 2635, 2621 manual Dhcp Server web

Page 85

Models 2603, 2621, and 2635 Getting Started Guide	8 • DHCP and DNS Configuration

Figure 55. DHCP Server web page

The server needs to have a subnet of IP addresses which will be allocated when a DHCP client makes a request. Deﬁne the subnet by clicking on the hyperlink Create new Subnet... The next webpage, ‘Create new DHCP Server subnet’ has four sections.

•Parameters for this subnet: deﬁnes the subnet and netmask, the origin of the subnet, maximum lease time, and default lease time.

•IP addresses to be available on this subnet: either deﬁne the IP address range for the DHCP server IP pool, or use the default range which is a set of 20 IP addresses.

•DNS server option information: enter the IP addresses of the primary and secondary DNS servers which are provided to the DHCP clients.

•Default gateway option information: You may use the local host as the default gateway.

ﬁgure 56 shows the entire conﬁguration web page for the DHCP server.

Introduction

85

Image 85

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsImpaired functioning General observations Factory default parametersGeneral conventions Typographical conventions used in this documentGeneral Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewProtocol support EthernetPPP Support WAN InterfacesSecurity Logging or Smtp on events POST, Post errors, PPP/DHCP, IPFront Panel Status LEDs and Console Port Console port Rear panel connectors and switchesOn the rear panel from left to right are the following Ethernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Conﬁguration Interface cable installation Hardware installationWhat you will need RJ-48C pinout diagram Initial Configuration Ethernet connector Interface connector RJ-45 DB-15 Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cableIP address has now been successfully changed IP address modiﬁcationWeb Operation and Conﬁguration PC ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Serial Interface WAN Serial Port ConﬁgurationVariables T1/E1 Interface Conﬁguration Web Interface ConﬁgurationWeb Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 OperationConﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services PPP Conﬁguration WAN Service ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP RoutedPPP Routed Conﬁguration menu Click on CreateEdit IP address of WAN port Click the Update buttonPPP link status LMI Management Frame Relay links Username blank Password blank Click on the Create buttonLMI Conﬁguration Web Conﬁguration Methods Dlci Number Use Frame Relay ConﬁgurationFrame Relay bridged creation Frame Relay bridgedCentral site conﬁguration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed conﬁguration IP route for Frame Relay routed application Cost Interface frame-0WAN Services Security Conﬁguring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfacesSecurity conﬁguration home Click on the hyperlink New Policy... See ﬁgure Conﬁguring Security PoliciesFirewall Portﬁlters Enabling the FirewallDeleting a security Policy You can now ping between the two networks Security TriggersConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Enabling NAT Introduction to NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnetNext section see ﬁgure 58. has three parameters IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolAdditional option information Default gateway option informationDhcp Relay Conﬁguration of the Dhcp RelayDhcp Relay webpage Conﬁguring the DNS Relay DNS RelayDNS Relay conﬁguration webpage IP Services Next command disables the WEB server IP ServicesWEB Server CLI ConﬁgurationAssociated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser AuthenticationAccess the conﬁguration and status of the alarms AlarmAlarm & Alarm Error Log conﬁguration Remote AccessBackup/Restore UpdateSave Restart Website SettingsSnmp Daemon Error LogSnmp Daemon conﬁguration System ToolsSntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration ParametersSntp Client General Conﬁguration Parameters System Clock SettingConﬁguration of the internal system calendar clock System Status Port Connection Status System StatusMAC address the MAC address of the Ethernet port LAN StatusWAN Status Hardware StatusStatus LEDs Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersEMC Appendix a Compliance informationRadio and TV Interference FCC Part ComplianceCE Declaration of Conformity FCC Part 68 Acta Statement Model 2603 onlyIndustry Canada Notice 2603 Model only Appendix B Speciﬁcations Ethernet General CharacteristicsSync Serial Interface T1/E1 InterfacePPP Support Protocol SupportManagement Power and Power Supply Speciﬁcations DimensionsAC universal power supply VDC power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port Assuming the MDI-X switch is in the out positionRJ-45 non-shielded RS-232 console port EIA-561 Serial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation CLI Terminology Using the ConsoleProduces a list of numbered transport objects Local VT-100 emulationThen Another example shows when the user must provide a parameterSetting user passwords Administering user accountsEnter the new password twice as prompted Adding new usersControlling login access Changing user settingsControlling user access For example, to change the security level for fred, enter

Related manuals

Manual 133 pages 54.65 Kb