Patton electronic 2621 Hardware installation, What you will need, Interface cable installation

Page 28

Models 2603, 2621, and 2635 Getting Started Guide	3 • Initial Configuration

Hardware installation

If you are already familiar with IPLink Series Router installation and conﬁguration, this chapter will enable you to ﬁnish the job quickly. Installation consists of the following:

•Preparing for the installation (see section “What you will need”)

•Installing the T1/E1 WAN, X.21, or V.35 interface cable (see section “Interface cable installation”)

•Hooking up network cables, verifying that the unit will power up, and running a HyperTerminal session (see section “Installing the Ethernet cable” on page 36)

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

•Changing the IP address from the factory default setting (see section “IP address modiﬁcation” on page 37)

•Launching a web browser in preparation for conﬁguring the modem (see “Web Operation and Conﬁgura- tion” on page 37)

What you will need

•IPLink Series High Speed Router

•Ethernet cable with RJ45 plugs on each end (included with router)

•DB9-RJ45 adapter (included with router)

•RJ45/RJ45 straight-through cable for connecting to control port (included with router)

•PC computer with HyperTerminal or equivalent VT-100 emulation program, or an ASCII terminal (also called a dumb terminal) capable of emulating a VT-100.

Interface cable installation

An IPLink Series router comes with a T1/E1 WAN, V.35, or X.21 interface. Refer to the appropriate section to install an interface cable on your IPLink router:

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

•Model 2603 router (see “Installing an interface cable on the IPLink 2603’s T1/E1 interface port” on page 29)

•Model 2621 router (see “Installing an interface cable on the IPLink 2621’s X.21 interface port” on page 31)

•Model 2635 router (see “Installing an interface cable on the IPLink 2635’s V.35 interface port” on page 33)

Hardware installation

28

Image 28

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsImpaired functioning Factory default parameters General observationsTypographical conventions used in this document General conventionsChapter contents General InformationIPLink Series High Speed Routers overview General attributesEthernet Protocol supportPPP Support WAN InterfacesSecurity Logging or Smtp on events POST, Post errors, PPP/DHCP, IPFront Panel Status LEDs and Console Port Console port Rear panel connectors and switchesOn the rear panel from left to right are the following Power connector Ethernet port outlined in greenGeneral Information Product Overview Introduction Applications Overview Sync Serial ApplicationInitial Conﬁguration Interface cable installation Hardware installationWhat you will need RJ-48C pinout diagram Initial Configuration Ethernet connector Interface connector RJ-45 DB-15 Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 Installing the AC power cord DCEInitial Configuration Installing the Ethernet cable Do the followingIP address modiﬁcation IP address has now been successfully changedWeb Operation and Conﬁguration PC ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port LAN Connections Ethernet PortBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Serial Interface WAN Serial Port ConﬁgurationVariables Web Interface Conﬁguration T1/E1 Interface ConﬁgurationConﬁguring the IPLink Series 2603 for T1 Operation Web Conﬁguration , enter username See ﬁgureLine Options Fractional T1 Conﬁguring the IPLink Series 2603 for E1 OperationSerial Port Configuration WAN Services PPP BridgedWAN Services PPP Conﬁguration WAN Service ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create PPP Routed Remote site conﬁgurationClick on Create PPP Routed Conﬁguration menuClick the Update button Edit IP address of WAN portPPP link status LMI Management Frame Relay links Username blank Password blank Click on the Create buttonLMI Conﬁguration Web Conﬁguration Methods Frame Relay Conﬁguration Dlci Number UseFrame Relay bridged Frame Relay bridged creationCentral site conﬁguration Frame Relay Routed RelayDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 IP route for Frame Relay routed applicationWAN Services Security Click on Create a new service Conﬁguring the routerClick on the Create a new Ip route... hyperlink Conﬁguring the security interfaces Valid gateway routeSecurity conﬁguration home Conﬁguring Security Policies Click on the hyperlink New Policy... See ﬁgureFirewall Portﬁlters Enabling the FirewallDeleting a security Policy Security Triggers You can now ping between the two networksConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Intrusion Detection System IDS Attack Name Protocol Attacking Host Blacklisted?Security Enabling NAT Introduction to NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other Dhcp Server NATDhcp Server web Parameters for the Dhcp Server subnet Dhcp server conﬁguration webIP Addresses to be available on this subnet Next section see ﬁgure 58. has three parametersExample based on default range of IP address pool DNS server option informationDefault gateway option information Additional option informationDhcp Relay Conﬁguration of the Dhcp RelayDhcp Relay webpage DNS Relay Conﬁguring the DNS RelayDNS Relay conﬁguration webpage IP Services IP Services Next command disables the WEB serverWEB Server CLI ConﬁgurationAssociated Ports for the different System IP Services System Conﬁguration Authentication Authentication web page showing default superuserAlarm Access the conﬁguration and status of the alarmsRemote Access Alarm & Alarm Error Log conﬁgurationBackup/Restore UpdateSave Website Settings RestartError Log Snmp DaemonSystem Tools Snmp Daemon conﬁgurationSntp Client Conﬁguration Sntp Client Mode Conﬁguration Parameters Conﬁguring the Sntp ClientSystem Clock Setting Sntp Client General Conﬁguration ParametersConﬁguration of the internal system calendar clock System Status System Status Port Connection StatusLAN Status MAC address the MAC address of the Ethernet portWAN Status Hardware StatusStatus LEDs Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information EMCCompliance Radio and TV Interference FCC PartCE Declaration of Conformity FCC Part 68 Acta Statement Model 2603 onlyIndustry Canada Notice 2603 Model only Appendix B Speciﬁcations General Characteristics EthernetSync Serial Interface T1/E1 InterfacePPP Support Protocol SupportManagement Dimensions Power and Power Supply SpeciﬁcationsAC universal power supply VDC power supplyAppendix C Cable Recommendations Ethernet Cable AdapterAppendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port Assuming the MDI-X switch is in the out positionRJ-45 non-shielded RS-232 console port EIA-561 35 M/34 and DB-25 Connector Serial port21 DB-15 Connector Pin No Circuit Signal Name DirectionE1/T1 RJ-48C Connector Pin No SignalAppendix E Command Line Interface CLI Operation Using the Console CLI TerminologyProduces a list of numbered transport objects Local VT-100 emulationAnother example shows when the user must provide a parameter ThenAdministering user accounts Setting user passwordsEnter the new password twice as prompted Adding new usersChanging user settings Controlling login accessControlling user access For example, to change the security level for fred, enter

Related manuals

Manual 133 pages 54.65 Kb