Patton electronic 2621, 2635 manual Compliance, Radio and TV Interference FCC Part

Page 116

Models 2603, 2621, and 2635 Getting Started Guide	A • Compliance information

Compliance

EMC

•FCC Part 15, Class A

•EN55022, Class A

•EN55024

Safety

•UL 60950-1/CSA C22.2 N0. 60950-1

•IEC/EN60950-1

•AS/NZS 60950-1

PSTN Regulatory (2603 Model only)

•ACTA Part 68

•CS03

•AS/ACIF S016

Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television recep- tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accordance with the speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide reason- able protection from such interference in a commercial installation. However, there is no guarantee that inter- ference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by disconnecting the cables, try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna, and/or plugging the receiving equipment into a different AC outlet (such that the computing equip- ment and receiver are on different branches).

CE Declaration of Conformity

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec- ognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded at www.patton.com/certiﬁcations

FCC Part 68 (ACTA) Statement (Model 2603 only)

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identiﬁer in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

Compliance

116

Image 116

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity Factory default parameters General observationsTypographical conventions used in this document General conventionsChapter contents General InformationIPLink Series High Speed Routers overview General attributesEthernet Protocol supportPPP Support WAN InterfacesFront Panel Status LEDs and Console Port Logging or Smtp on events POST, Post errors, PPP/DHCP, IPSecurity On the rear panel from left to right are the following Rear panel connectors and switchesConsole port Power connector Ethernet port outlined in greenGeneral Information Product Overview Introduction Applications Overview Sync Serial ApplicationInitial Conﬁguration What you will need Hardware installationInterface cable installation RJ-48C pinout diagram Initial Configuration Ethernet connector Interface connector RJ-45 DB-15 Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 Installing the AC power cord DCEInitial Configuration Installing the Ethernet cable Do the followingIP address modiﬁcation IP address has now been successfully changedWeb Operation and Conﬁguration PC ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port LAN Connections Ethernet PortBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Variables WAN Serial Port ConﬁgurationSerial Interface Web Interface Conﬁguration T1/E1 Interface ConﬁgurationConﬁguring the IPLink Series 2603 for T1 Operation Web Conﬁguration , enter username See ﬁgureLine Options Fractional T1 Conﬁguring the IPLink Series 2603 for E1 OperationSerial Port Configuration WAN Services PPP BridgedWAN Services PPP Bridged WAN Service ConﬁgurationPPP Conﬁguration Leave User name and Password blank. Click on Create PPP Routed Remote site conﬁgurationClick on Create PPP Routed Conﬁguration menuClick the Update button Edit IP address of WAN portPPP link status LMI Conﬁguration Username blank Password blank Click on the Create buttonLMI Management Frame Relay links Web Conﬁguration Methods Frame Relay Conﬁguration Dlci Number UseFrame Relay bridged Frame Relay bridged creationCentral site conﬁguration Frame Relay Routed RelayDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 IP route for Frame Relay routed applicationWAN Services Security Click on Create a new service Conﬁguring the routerClick on the Create a new Ip route... hyperlink Conﬁguring the security interfaces Valid gateway routeSecurity conﬁguration home Conﬁguring Security Policies Click on the hyperlink New Policy... See ﬁgureDeleting a security Policy Enabling the FirewallFirewall Portﬁlters Security Triggers You can now ping between the two networksConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Intrusion Detection System IDS Attack Name Protocol Attacking Host Blacklisted?Security Global address pool and reserved map Introduction to NATEnabling NAT Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other Dhcp Server NATDhcp Server web Parameters for the Dhcp Server subnet Dhcp server conﬁguration webIP Addresses to be available on this subnet Next section see ﬁgure 58. has three parametersExample based on default range of IP address pool DNS server option informationDefault gateway option information Additional option informationDhcp Relay Conﬁguration of the Dhcp RelayDhcp Relay webpage DNS Relay Conﬁguring the DNS RelayDNS Relay conﬁguration webpage IP Services IP Services Next command disables the WEB serverWEB Server CLI ConﬁgurationAssociated Ports for the different System IP Services System Conﬁguration Authentication Authentication web page showing default superuserAlarm Access the conﬁguration and status of the alarmsRemote Access Alarm & Alarm Error Log conﬁgurationSave UpdateBackup/Restore Website Settings RestartError Log Snmp DaemonSystem Tools Snmp Daemon conﬁgurationSntp Client Conﬁguration Sntp Client Mode Conﬁguration Parameters Conﬁguring the Sntp ClientSystem Clock Setting Sntp Client General Conﬁguration ParametersConﬁguration of the internal system calendar clock System Status System Status Port Connection StatusLAN Status MAC address the MAC address of the Ethernet portWAN Status Hardware StatusStatus LEDs Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information EMCCompliance Radio and TV Interference FCC PartCE Declaration of Conformity FCC Part 68 Acta Statement Model 2603 onlyIndustry Canada Notice 2603 Model only Appendix B Speciﬁcations General Characteristics EthernetSync Serial Interface T1/E1 InterfaceManagement Protocol SupportPPP Support Dimensions Power and Power Supply SpeciﬁcationsAC universal power supply VDC power supplyAppendix C Cable Recommendations Ethernet Cable AdapterAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 Assuming the MDI-X switch is in the out positionRJ-45 shielded 10/100 Ethernet port 35 M/34 and DB-25 Connector Serial port21 DB-15 Connector Pin No Circuit Signal Name DirectionE1/T1 RJ-48C Connector Pin No SignalAppendix E Command Line Interface CLI Operation Using the Console CLI TerminologyProduces a list of numbered transport objects Local VT-100 emulationAnother example shows when the user must provide a parameter ThenAdministering user accounts Setting user passwordsEnter the new password twice as prompted Adding new usersChanging user settings Controlling login accessControlling user access For example, to change the security level for fred, enter

Related manuals

Manual 133 pages 54.65 Kb