Patton electronic manual SN4950-NCE model codes, NCE/4E120V/EUI

Page 15

SmartNode 4950-NCE Getting Started Guide	1 • General information

SN4950-NCE model codes

The SmartNode 4950-NCE series consists of several models. They differ in the number of PRI ports and voice channels supported. All models come equipped with two 10/100/1000Base-T Ethernet ports. The SmartNode 4950-NCE PRI ports and voice channels are listed in table 2. The SmartNode 4950-NCE G.SHDSL models are listed in table 3.

Table 2. SmartNode 4950-NCE PRI Ports and Voice Channels

Model	PRI Ports	Voice Channels

SN4950-	1	24
NCE/1E24V/EUI
SN4950-	1	30
NCE/1E30V/EUI

SN4950-	4	24
NCE/4E24V/EUI
SN4950-	4	30
NCE/4E30V/EUI

SN4950-	4	48
NCE/4E48V/EUI
SN4950-	4	60
NCE/4E60V/EUI

SN4950-	4	96
NCE/4E96V/EUI
SN4950-	4	120
NCE/4E120V/EUI

Table 3. SmartNode 4950-NCE models with integrated G.SHDSL interface

Model	PRI Ports	Voice Channels

SN4950-	1	24
NCE/1E24V2GS/EUI
SN4950-	1	30
NCE/1E30V2GS/EUI

SN4950-	4	24
NCE/4E24V2GS/EUI
SN4950-	4	30
NCE/4E30V2GS/EUI

SN4950-	4	48
NCE/4E48V2GS/EUI
SN4950-	4	60
NCE/4E60V2GS/EUI

SN4950-	4	96
NCE/4E96V2GS/EUI
SN4950-	4	120
NCE/4E120V2GS/EUI

SmartNode 4950-NCE overview

15

Image 15

Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables About this guide AudienceStructure Impaired functioning PrecautionsSafety when working with electricity Convention Meaning Typographical conventions used in this documentGeneral observations General conventionsGeneral information Chapter contentsSmartNode 4950-NCE SmartNode 4950-NCE overviewNCE/4E120V/EUI SN4950-NCE model codesSN4951-NCE model codes SmartNode 4950-NCE rear panelWAN ETH 0/0 SN4950/4E120V SmartNode 4950-NCE front panelDescription LEDApplications overview Introduction Application-Multi-service Isdn Internet telephony IADSmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Configuring the desired IP addressFactory-default IP settings LoginConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Step Command Purpose BootloaderStart Bootloader Start-up with factory configurationStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Command Purpose Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Using PVC channels with PPPoEDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Pstn Regulatory ComplianceAppendix B Specifications Fax and modem support Voice processing signalling dependentVoice connectivity Data connectivityVoice signalling IP servicesVoice routing-session router Management SystemPhysical Factor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpSmartNode Model SysObjectID Appendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port Pin SignalPRI port Shdsl portPin Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination