Patton electronic 4950-NCE manual Termination, Other licenses

Page 65

SmartNode 4950-NCE Getting Started Guide

F • End user license agreement

 

 

If the Program(s) are acquired by or on behalf of a unit or agency of the United States Government, the Gov- ernment agrees that such Program(s) are commercial computer software or computer software documentation and that, absent a written agreement to the contrary, the Government’s rights with respect to such Program(s) are limited by the terms of this Agreement, pursuant to Federal Acquisition Regulations 12.212(a) and/or DEARS 227.7202-1(a) and/or sub-paragraphs (a) through (d) of the “Commercial Computer Software - Restricted Rights” clause at 48 C.F.R. 52.227-19 of the Federal Acquisition Regulations as applicable.

6. Termination

A)The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s).

B)Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License” on page 64.

C)Upon termination for A or B above or the end of the Term, End User is required to destroy all copies of the licensed Program(s)

7. Other licenses

The Program may be subject to licenses extended by third parties. Accordingly, Patton Electronics Company licenses the Programs subject to the terms and conditions dictated by third parties. Third party software identi- fied to the Programs includes:

A routing license is included at no charge.

MGCP capabilities will require the purchase of an additional license.

The LGPL (Lesser General Public License) open source license distributed to you pursuant to the LGPL license terms (http://www.gnu.org/licenses/lgpl.html).

RedBoot (Red Hat Embedded Debug and Bootstrap) embedded system debug/bootstrap environment from Red Hat distributed to you pursuant to the eCos license terms (http://ecos.sourceware.org/license- overview.html) and GNU General Public License (GPL) terms (http://www.gnu.org/copyleft/gpl.html). Source code is available upon request.

End User License Agreement

65

Image 65
Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions Convention MeaningGeneral information Chapter contentsSmartNode 4950-NCE SmartNode 4950-NCE overviewNCE/4E120V/EUI SN4950-NCE model codesSN4951-NCE model codes SmartNode 4950-NCE rear panelWAN ETH 0/0 SN4950/4E120V SmartNode 4950-NCE front panelDescription LEDApplications overview Introduction Application-Multi-service Isdn Internet telephony IADSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information Pstn Regulatory ComplianceAppendix B Specifications Voice connectivity Voice processing signalling dependentData connectivity Fax and modem supportVoice routing-session router Voice signallingIP services Physical ManagementSystem Factor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpSmartNode Model SysObjectID Appendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port Pin SignalPin PRI portShdsl port Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination