Patton electronic 4950-NCE manual Introduction

Page 62

SmartNode 4950-NCE Getting Started GuideE • SmartNode 4950-NCE factory configuration

Introduction

The factory configuration settings for SmartNode 4950-NCE are as follows:

#----------------------------------------------------------------	#
#	#
# 4950-NCE Series	#
# Factory configuration file	#
#	#
#----------------------------------------------------------------	#
dns-relay
sntp-client
sntp-client server primary 129.132.2.21 port 123 version 4
system
ic voice 0
low-bitrate-codec g729
profile napt NAPT_WAN
profile dhcp-server DHCPS_LAN
network 192.168.1.0 255.255.255.0
include 1 192.168.1.10 192.168.1.99
lease 2 hours
default-router 1.192.168.1.1
domain-name-server 1.192.168.1.1
context ip router
interface WAN
ipadress dhcp
use profile napt NAPT_WAN
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
interface LAN
ipadress 192.168.1.1 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context ip router
dhcp-server use DHCPS_LAN
port ethernet 0 0
medium auto
encapsulation ip
bimd interface WAN router
no shutdown
port ethernet 0 1
medium auto
encapsulation ip
bind interface LAN router
no shutdown

Introduction

62

Image 62

Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations Convention MeaningChapter contents General informationSmartNode 4950-NCE overview SmartNode 4950-NCESN4950-NCE model codes NCE/4E120V/EUISmartNode 4950-NCE rear panel SN4951-NCE model codesWAN ETH 0/0 SmartNode 4950-NCE front panel SN4950/4E120VLED DescriptionApplications overview Application-Multi-service Isdn Internet telephony IAD IntroductionSmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCLogin Configuring the desired IP addressFactory-default IP settings Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Start-up with factory configuration BootloaderStart Bootloader Step Command PurposeStep Command Purpose Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Using PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Command PurposeTroubleshooting DSL Connections DiagnosticsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Compliance Pstn RegulatoryAppendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Fax and modem supportVoice routing-session router Voice signallingIP services Physical ManagementSystem Shdsl Daughter Card if applicable Factor SpecsIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDSmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Pin Signal Console portPin PRI portShdsl port Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses