Patton electronic 4950-NCE manual Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables

Page 25

SmartNode 4950-NCE Getting Started Guide	3 • SmartNode installation

Connect the cables in the following order:

The interconnecting cables shall be acceptable for external use

and shall be rated for the proper application with respect to volt-

age, current, anticipated temperature, flammability, and

CAUTION mechanical serviceability.

1.Connect the T1/E1 cables to the PRI T1/E1 ports (see Appendix C on page 53 and Appendix D on page 58).

2.Connect the 10/100/1000Base-T Ethernet LAN and WAN (see section “Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables” on page 25)

3.Connect the power mains cable (see section “Connecting the power supply” on page 26)

Connecting the PRI

The SmartNode comes with one or four PRI ports. These ports are usually connected to a PBX or switch (local exchange (LE) ). Each PRI T1/E1 port is a RJ-48C receptacle. In most cases, a straight-through RJ-45 can be used to connect the PRI. Each port can be configured as NT (clock master) or TE (clock slave).

For details on the PRI port pin-out and ISDN cables, refer to Appendix C, “Cabling” on page 43 and Appen- dix D, “port pin-outs” on page 47.

Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables

The SmartNode 4950-NCE has automatic MDX (auto-crossover) detection and configuration on all Ethernet ports. Any of the ports can be connected to a host or hub/switch with a straight-through or cross-over wired cable.

1.Connect to the subscriber port of the broadband access modem (DSL, cable, WLL) to ETH 0/0.

Note The SmartNode Ethernet ports operate in Full Duplex mode only. Do not connect to Half Duplex ports. For best results, use auto-negotiation. Auto negotiation is mandatory when using 1000BaseT (Gigabit) Ethernet.

2.Connect port ETH 0/1 to your LAN.

Installing the DSL WAN cable. The SmartNode Model 4950-NCE comes with an option for a G.SHDSL WAN interface. Use a straight-through RJ-11 cable to connect the G.SHDSL port.

For details on the Ethernet port pinout and cables, refer to Appendix C, “Cabling” on page 53 and Appendix D, “Port pin-outs”on page 58.

Installing the gateway router

25

Image 25

Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions Convention MeaningGeneral information Chapter contentsSmartNode 4950-NCE SmartNode 4950-NCE overviewNCE/4E120V/EUI SN4950-NCE model codesSN4951-NCE model codes SmartNode 4950-NCE rear panelWAN ETH 0/0 SN4950/4E120V SmartNode 4950-NCE front panelDescription LEDApplications overview Introduction Application-Multi-service Isdn Internet telephony IADSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Pstn Regulatory ComplianceAppendix B Specifications Voice connectivity Voice processing signalling dependentData connectivity Fax and modem supportIP services Voice signallingVoice routing-session router System ManagementPhysical Factor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpSmartNode Model SysObjectID Appendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port Pin SignalShdsl port PRI portPin Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination