Patton electronic manual SmartNode 4950-NCE front panel, SN4950/4E120V

Page 18

SmartNode 4950-NCE Getting Started Guide	1 • General information

SmartNode 4950-NCE front panel

Figure 3 shows SmartNode 4950-NCE front panel LEDs, the LED definitions are listed in table 5.

	0
1Port
T1/E	Port1
	T1/E1	2
	1Port
	T1/E	Port3
		T1/E1

Multi-
Port	T1/	SmartNodeIP
	E1/P
		RIV
		erpri4950
		Ent	GatVoIP
		se	GatVoIP
			ayRIAD
			ew
			outer

	SN4950/1E30V
	SmartNode 4950 VoIP IAD
	Multi-Port T1/E1/PRI VoIP Enterprise Gateway Router
Power
Activity	T1/E1 Port 0

VoIP			Ethernet 0/1
VoIP			Activity
Ethernet 0/0	Ethernet 0/0	Ethernet 0/1	Ethernet 0/1
Link	1000	Link	1000

Ethernet 0/0	Ethernet 0/0	Ethernet 0/1
100	Activity	100								SN4950/4E120V
										SN4950/4E120V
										SmartNode 4950 VoIP IAD
										Multi-Port T1/E1/PRI VoIP Enterprise Gateway Router
			Port	0	Port	1	Port	2	Port	3
		T1/E1	Port		Port		Port		Port
		T1/E1	T1/E1		T1/E1		T1/E1

T1/E1 Port 0	T1/E1 Port 3
T1/E1 Port 1	T1/E1 Port 2

Figure 3. SmartNode 4950-NCE front panel

SmartNode 4950-NCE front panel

18

Image 18

Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables About this guide AudienceStructure Precautions Impaired functioningSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations Convention MeaningChapter contents General informationSmartNode 4950-NCE overview SmartNode 4950-NCESN4950-NCE model codes NCE/4E120V/EUISmartNode 4950-NCE rear panel SN4951-NCE model codesWAN ETH 0/0 SmartNode 4950-NCE front panel SN4950/4E120VLED DescriptionApplications overview Application-Multi-service Isdn Internet telephony IAD IntroductionSmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCLogin Configuring the desired IP addressFactory-default IP settings Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Start-up with factory configuration BootloaderStart Bootloader Step Command PurposeStep Command Purpose Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Using PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Command PurposeTroubleshooting DSL Connections DiagnosticsContacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Compliance Pstn RegulatoryAppendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Fax and modem supportVoice signalling IP servicesVoice routing-session router Management SystemPhysical Shdsl Daughter Card if applicable Factor SpecsIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDSmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Pin Signal Console portPRI port Shdsl portPin Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses