Patton electronic 4950-NCE manual Line Setup, Configuring PPPoE

Page 37

SmartNode 4950-NCE Getting Started Guide	5 • G.SHDSL Basic Configuration

Introduction

The SN4950-NCE model has an option for a built-in G.SHDSL modem. The modem appears in the configu- ration as "port dsl 0 0" mode.

Profile

napt

WAN

port dsl 0\ 0\

	pvc
vpi 8	vci 35

pppoe

session MyISP

use
profile
WAN	napt

WAN

interface

bind subscriber
	MySubscriber
interface
bind	router
WAN

Subscriber PPP MySubscriber

CAUTION

context

ip

Figure 8. Configuring the G.SHDSL card for PPPoE

The Modem setup uses IP messages within its own subnet: 192.0.2.0/24. SmartNodes with built-in modems cannot use this subnet in any other way.

Note For information about the specifications of the G.SHDSL daughter card, see Appendix B, “Specifications” on page 46.

Line Setup

There is no line modulation setting. The modems automatically adapt to the bit rate and modulation used. The status LED on the back of the device is blinking while the modem attempts to connect and lit when the link is established. If the modem keeps blinking, check the cabling,

Configuring PPPoE

Figure 8 explains how to configure PPPoE on the SmartNode’s built-in G.SHDSL card. To configure the DSL port for PPPoE, first you need to log in to the SmartNode via the CLI and enter configuration mode.

login: administrator

password: <enter> SN4xxx>enable SN4xxx>#configure

Introduction

37

Image 37

Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions Convention MeaningGeneral information Chapter contentsSmartNode 4950-NCE SmartNode 4950-NCE overviewNCE/4E120V/EUI SN4950-NCE model codesSN4951-NCE model codes SmartNode 4950-NCE rear panelWAN ETH 0/0 SN4950/4E120V SmartNode 4950-NCE front panelDescription LEDApplications overview Introduction Application-Multi-service Isdn Internet telephony IADSmartNode installation Network Diagram Planning the installationSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCFactory-default IP settings Configuring the desired IP addressLogin Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Start Bootloader BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupConfiguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Command PurposeDiagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Pstn Regulatory ComplianceAppendix B Specifications Voice connectivity Voice processing signalling dependentData connectivity Fax and modem supportIP services Voice signallingVoice routing-session router System ManagementPhysical Factor Specs Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpSmartNode Model SysObjectID Appendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port Pin SignalShdsl port PRI portPin Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination