Patton electronic 4950-NCE manual SmartNode Model SysObjectID

Page 52

SmartNode 4950-NCE Getting Started Guide	B • Specifications

Table 13. SmartNode Models and their Unique sysObjectID (Continued)

SmartNode Model	SysObjectID

SN4951/4E96V	.iso.org.dod.internet.private.enterprises.patton.products.sn49xx.19
	1.3.6.1.4.1.1768.100.4.15.19

SN4951/4E120V	.iso.org.dod.internet.private.enterprises.patton.products.sn49xx.20
	1.3.6.1.4.1.1768.100.4.15.20

Note The SysObjectIDs for the SN4950-NCE G.SHDSL models are the same as the corresponding non-G.SHDSL models listed above.

According to table 13, an SNMP get request to .iso.org.dod.internet.mgmt.mib-2.system.sysObjectID of a Smart- Node 4950/1E30V2GS/EUI-NCE device reads out a numeric OID of 1.3.6.1.4.1.1768.100.4.15.1. The mapping of the sysObjectID to each of the SmartNode model is realized with the SmartNode product identifi- cation MIB.

The SNMP agent running in SmartWare is SNMP version 1 (SNMPv1) compliant. SNMP version 2 (SNMPv2) and SNMP version 3 (SNMPv3) are not currently supported.

IMPORTANT

Identification of the SmartNode devices via SNMP

52

Image 52

Contents SmartNode 4950-NCE Series Mailsupport@patton.com Summary Table of Contents Table of Contents Compliance information Cabling List of Figures List of Tables Audience About this guideStructure Precautions Impaired functioningSafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions Convention MeaningChapter contents General informationSmartNode 4950-NCE overview SmartNode 4950-NCESN4950-NCE model codes NCE/4E120V/EUISmartNode 4950-NCE rear panel SN4951-NCE model codesWAN ETH 0/0 SmartNode 4950-NCE front panel SN4950/4E120VLED DescriptionApplications overview Application-Multi-service Isdn Internet telephony IAD IntroductionSmartNode installation Planning the installation Network DiagramSite log Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCConfiguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Bootloader Start BootloaderStart-up with factory configuration Step Command PurposeStep Command Purpose Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Setting up permanent virtual circuits PVC Using PVC channels in bridged Ethernet modeUsing PVC channels with PPPoE Command PurposeTroubleshooting DSL Connections DiagnosticsContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Compliance Pstn RegulatoryAppendix B Specifications Voice processing signalling dependent Voice connectivityData connectivity Fax and modem supportIP services Voice signallingVoice routing-session router System ManagementPhysical Shdsl Daughter Card if applicable Factor SpecsIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDSmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Pin Signal Console portShdsl port PRI portPin Appendix E SmartNode 4950-NCE factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses