Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.

Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

 

Standard Depth

Counter Depth

 

Models

Models

Sides

1/8(3 mm)

1/8(3 mm)

Top

1(25 mm)

1(25 mm)

Back

1(25 mm)

1/2(13 mm)

REMOVE TOP CAP (on some models)

IMPORTANT NOTE: This refrigerator is 34-1/2deep.

Doors and passageways leading to the installation location must be at least 36wide in order to leave the doors and handles attached to the refrigerator

while transporting it into the installation location. If passageways are less than 36, the refrigerator doors and handles can easily be scratched and damaged. The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. Start with Step A.

If it is not necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the refrigerator is in the final location.

SKID REMOVAL: Tilt refrigerator to each side to remove skid.

NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand truck with a side against the truck. We strongly recommend that TWO PEOPLE move and complete this installation.

ALocate and remove the two Phillips head screws on the top of the refrigerator. Remove the two screws on each side at the rear of the top cap. Lift off and remove top cap.

BRemove the fresh-food door. Refer to Steps 1 through 3 of “Reversing the Door Swing” section.

CRemove the bottom freezer drawer. Refer to “Removing Freezer Drawers” section.

DMove refrigerator to the installation location.

REMOVE TOP CAP (cont.) (on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

ECarefully lower the door onto the center hinge. Reinstall top hinge. NOTE: Ensure the door is properly aligned to the case top to avoid readjustment of the door during top cap reinstallation.

FPlace cap over the top of the refrigerator. Reinstall the original screws in the top and back of the cap.

GReinstall the bottom freezer drawer. Refer to “Replacing the Freezer Drawers” section.

A

Top

Hinge B

1CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker operation. If there is not a cold water supply, you

will need to provide one. See Installing the Water Line section.

NOTES:

Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

If your refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnectRefrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

18

Page 18
Image 18
GE 225D1804P001 Installing the Refrigerator, Refrigerator Location, Clearances, Reinstall DOORS, Drawers and TOP CAP

225D1804P001 specifications

The GE 225D1804P001 is a cutting-edge electric motor that stands out in its class due to its innovative design and advanced technologies. This particular motor exemplifies General Electric's commitment to excellence, blending efficiency, reliability, and performance in one compact device.

One of the main features of the GE 225D1804P001 is its robust construction, designed to withstand demanding industrial environments. The motor is built with high-quality materials that enhance its durability, making it suitable for continuous operation under heavy loads. Its weather-resistant exterior allows it to perform seamlessly in adverse conditions, further extending its lifespan.

In terms of technology, this motor incorporates state-of-the-art variable frequency drive (VFD) compatibility, which enables precise speed control and energy efficiency. The VFD technology allows users to adjust the motor’s speed according to the specific needs of their applications, resulting in energy savings and reduced wear and tear on machinery.

The GE 225D1804P001 also features high starting torque, which is essential for applications requiring a strong initial force to overcome inertia. This characteristic makes it ideal for heavy machinery and equipment within manufacturing, automotive, and industrial sectors. Additionally, the motor's optimized rotor design contributes to improved performance, ensuring effective torque delivery and lower operational costs.

Another significant characteristic of this model is its low noise operation. Unlike many electric motors, the GE 225D1804P001 is engineered to minimize vibrations and sound levels, creating a more comfortable working environment. This feature is particularly beneficial for facilities that operate in close proximity to populated areas or sensitive environments.

Moreover, the ease of maintenance is a noteworthy aspect of this electric motor. It is designed with accessible components, allowing technicians to perform routine checks and repairs without extensive downtime. This user-friendly design not only enhances operational efficiency but also contributes to the overall cost-effectiveness of ownership.

In summary, the GE 225D1804P001 electric motor combines innovation, efficiency, and reliability, making it an exceptional choice for a wide range of industrial applications. With features like VFD compatibility, high starting torque, robust construction, and low noise operation, it continues to set new standards in the electric motor industry, satisfying the needs of modern manufacturing and industrial processes.