Performance Data Sheet

SmartWater Filtration System

GSWF Cartridge

This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.*

(100% safety factors built in for unmetered usage)

Standard No. 42: Aesthetic Effects

Parameter

USEPA

Influent

Influent Challenge

Effluent

 

% Reduction

Min. Required

 

MCL

Average

Concentration

Average

 

Maximum

Average

Minimum

Reduction

Chlorine

1.845 mg/L

2.0 mg/L+10%

< 0.05 mg/L

 

0.05 mg/L

> 97.29%

96.43%

> 50%

 

 

 

 

 

 

 

 

 

 

T & O

 

Particulate**

143,333 #/mL

at least 10,000 particles/mL

29.83 #/mL

 

140 #/mL

99.98%

99.91%

> 85%

Standard No. 53: Health Effects

Parameter

USEPA

Influent

Influent Challenge

Effluent

% Reduction

Min. Required

 

MCL

Average

Concentration

Average

Maximum

Average

Minimum

Reduction

Turbidity

1 NTU***

10.3 NTU***

1+1 NTU***

0.106 NTU

0.14 NTU

98.97%

98.61%

0.5 NTU

Cysts

99.95% Reduction

200,000 #/L

Minimum 50,000 L

0

0

> 99.99%

> 99.99%

> 99.95%

 

 

 

 

 

 

 

 

 

Lead at pH 6.5

0.015 mg/L

0.15 mg/L

0.15 mg/L+10%

< 0.001 mg/L

< 0.001 mg/L

> 99.33%

> 99.33%

0.010 mg/L

 

 

 

 

 

 

 

 

 

Lead at pH 8.5

0.015 mg/L

0.14 mg/L

0.15 mg/L+10%

0.001 mg/L

0.003 mg/L

> 99.29%

97.86%

0.010 mg/L

Lindane

0.0002 mg/L

0.0216 mg/L

0.002 mg/L+10%

< 0.00002 mg/L

< 0.00002 mg/L

99.07%

98.75%

0.0002 mg/L

 

 

 

 

 

 

 

 

 

Atrazine

0.003 mg/L

0.008 mg/L

0.009 mg/L+10%

< 0.002 mg/L

< 0.002 mg/L

> 76.12%

> 66.67%

0.003 mg/L

 

 

 

 

 

 

 

 

 

*Tested using a flow rate of 0.5 gpm; pressure of 60 psig; pH of 7.5 ± 0.5; temp. of 68° ± 5°F (20° ± 3°C) ** Measurement in Particles/ml. Particles used were 0.5-1 microns

*** NTU=Nephelometric Turbidity units

Operating Specifications

Capacity: certified for up to 750 gallons (2,838 l); up to six months

Pressure requirement: 40–120 psi (2.8–8.2 bar)

Temperature: 33–100ºF (0.6–38ºC)

Flow rate: 0.5 gpm (1.9 lpm)

General Installation/Operation/Maintenance Requirements

Flush new cartridge at full flow for 3 minutes to purge out trapped air.

Replace cartridge when flow becomes too slow.

Special Notices

Installation instructions, parts and service availability, and standard warranty are included with the product when shipped. This drinking water system must be maintained according to manufacturer’s instructions, including replacement of filter cartridges.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water. Check for compliance with the state and local laws and regulations.

Note that while the testing was performed under standard laboratory conditions, actual performance may vary. Systems must be installed and operated in accordance with manufacturer’s recommended procedures and guidelines.

System tested and certified by NSF International against Standard 42 for the reduction of chlorine, taste and odor, particulate Class I and Standard 53 for the reduction of cyst, lead, Lindane, Atrazine and turbidity.

NSF®

Manufactured for: General Electric Company, Louisville, KY 40225

45

Page 45
Image 45
GE 225D1804P001 installation instructions Nsf, Performance Data Sheet, Operating Specifications, Special Notices

225D1804P001 specifications

The GE 225D1804P001 is a cutting-edge electric motor that stands out in its class due to its innovative design and advanced technologies. This particular motor exemplifies General Electric's commitment to excellence, blending efficiency, reliability, and performance in one compact device.

One of the main features of the GE 225D1804P001 is its robust construction, designed to withstand demanding industrial environments. The motor is built with high-quality materials that enhance its durability, making it suitable for continuous operation under heavy loads. Its weather-resistant exterior allows it to perform seamlessly in adverse conditions, further extending its lifespan.

In terms of technology, this motor incorporates state-of-the-art variable frequency drive (VFD) compatibility, which enables precise speed control and energy efficiency. The VFD technology allows users to adjust the motor’s speed according to the specific needs of their applications, resulting in energy savings and reduced wear and tear on machinery.

The GE 225D1804P001 also features high starting torque, which is essential for applications requiring a strong initial force to overcome inertia. This characteristic makes it ideal for heavy machinery and equipment within manufacturing, automotive, and industrial sectors. Additionally, the motor's optimized rotor design contributes to improved performance, ensuring effective torque delivery and lower operational costs.

Another significant characteristic of this model is its low noise operation. Unlike many electric motors, the GE 225D1804P001 is engineered to minimize vibrations and sound levels, creating a more comfortable working environment. This feature is particularly beneficial for facilities that operate in close proximity to populated areas or sensitive environments.

Moreover, the ease of maintenance is a noteworthy aspect of this electric motor. It is designed with accessible components, allowing technicians to perform routine checks and repairs without extensive downtime. This user-friendly design not only enhances operational efficiency but also contributes to the overall cost-effectiveness of ownership.

In summary, the GE 225D1804P001 electric motor combines innovation, efficiency, and reliability, making it an exceptional choice for a wide range of industrial applications. With features like VFD compatibility, high starting torque, robust construction, and low noise operation, it continues to set new standards in the electric motor industry, satisfying the needs of modern manufacturing and industrial processes.