TP-Link manual TL-WR340G/TL-WR340GD, 54Mbps Wireless Router User Guide

Page 15

Manual background

TL-WR340G/TL-WR340GD

54Mbps Wireless Router User Guide

Figure 2-4

2.In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties.

Figure 2-5

3.In the General tab of Internet Protocol (TCP/IP) Properties menu, highlight Internet Protocol (TCP/IP) under “This connection uses the following items:” by clicking on it once. Click on the Properties button.

8

Image 15

Contents Rev 1.0.4 TL-WR340G TL-WR340GD 54Mbps Wireless RouterAll rights reserved COPYRIGHT & TRADEMARKSFCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning Restriction National Restrictions2400.0-2483.5 MHz CountryETSI EN 300 DECLARATION OF CONFORMITYProduct Description 54Mbps Wireless Router Model No. TL-WR340G/TL-WR340GDChapter 3. Quick Installation Guide CONTENTSPackage Contents Hardware InstallationAppendix C Glossary Appendix A FAQAppendix B Configuring the PC Appendix C SpecificationsConventions Package Contents54Mbps Wireless Router User Guide 1.2 Main FeaturesChapter 1.Introduction 1.1 Product Overview¾ Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/2/1Mbps data transfer rates Indication Chapter 2.Hardware Installation2.1 The Front Panel LED Explanation2.3 System Requirements 2.2 The Back Panel2.5 Connecting the Device 2.4 Installation Environment Requirements2.6 Configure PC TL-WR340G/TL-WR340GD ¾ Configure the IP address manually Please check it following these steps 3.1 TCP/IP Configuration Chapter 3.Quick Installation GuidePlease check the connection following these steps Figure 3-1 Success result of Ping command3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-8 Quick Setup - Static IP 6. Click the Next button. You will then see the Finish page Chapter 4.Software Configuration 4.1 Login4.2 Status Please refer to Quick Installation Guide 4.3 Quick Setup4.4 Network 4.4.1 LAN4.4.2 WAN Figure 3-4 WAN - Dynamic IP Figure 3-5 WAN - Static IP Figure 3-6 WAN - PPPoE 3-7 will then appear Figure 3-7 PPPoE Advanced Settings Figure 3-8 802.1X + Dynamic IP Settings TL-WR340G/TL-WR340GD QLD - qld.bigpond.net.au NSW / ACT - nsw.bigpond.net.auTL-WR340G/TL-WR340GD 54Mbps Wireless Router User GuideTL-WR340G/TL-WR340GD ¾ Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise TL-WR340G/TL-WR340GD 54Mbps Wireless Router User GuideTL-WR340G/TL-WR340GD 54Mbps Wireless Router User GuideTL-WR340G/TL-WR340GD 4.4.3 MAC Clone 4.5 Wireless4.5.1 Wireless Settings TL-WR340G/TL-WR340GD WEP - Select WEP authentication type based on 802.11 authentications Figure 3-19 WPA-PSK/WPA2-PSK 4.5.2 MAC Filtering 5. Click the Save button to save this entry 4.5.3 Wireless Statistics 4.6 DHCP 4.6.1 DHCP Settings4.6.3 Address Reservation 4.6.2 DHCP Clients ListTo Reserve IP addresses The function wont take effect until the router reboots4.7 Forwarding 4.7.1 Virtual ServersTo setup a virtual server entry 4.7.2 Port Triggering TL-WR340G/TL-WR340GD 4.7.3 DMZ 4.7.4 UPnP 4.8.1 Firewall 4.8 Security4.8.2 IP Address Filtering 4.8.3 Domain Filtering TL-WR340G/TL-WR340GD 4.8.4 MAC Address Filtering 4.8.5 Remote Management 4.8.6 Advanced Security 4.9 Static Routing To add static routing entries 4.10 IP & MAC Binding Setting 4.10.1 Binding SettingTL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide To find an existing entry 4.10.2 ARP ListTo add IP & MAC Binding entries To modify or delete an existing entry4.11.1 Dyndns.org DDNS 4.11 Dynamic DNS4.11.2 Oray.net DDNS 4.11.3 Comexe.cn DDNS 4.12.1 Time 4.12 System Tools1. Select using daylight saving time 4.12.2 Diagnostic4.12.3 Firmware 4.12.4 Factory Defaults 4.12.6 Reboot 4.12.5 Backup & Restore4.12.8 Syslog 4.12.7 PasswordTotal 4.12.9 StatisticsStatistics Table IP Address1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? MAC CloneRemote Management 4. I want to build a WEB Server on the LAN, what should I do?Virtual Server 1. Configure TCP/IP component Appendix B Configuring the PCNow you have two ways to configure the TCP/IP protocol below ¾ Setting IP address automaticallyshown in the Figure below 1 Select Use the following IP address radio button. And the following items available ¾ Setting IP address manuallyClick OK to keep your settings Specifications Appendix CPhysical and Environment Appendix C Glossary

Related manuals

Manual 2 pages 7.63 Kb