TP-Link TL-WR340GD manual 4.10 IP & MAC Binding Setting

Page 65
TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide

TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide

Click the Delete All button to delete all entries

4.10 IP & MAC Binding Setting

Figure 3-49 the IP & MAC Binding menu

There are two submenus under the IP &MAC Binding menu (shown in Figure 3-49):Binding Setting and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below.

4.10.1 Binding Setting

This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire. (shown in Figure 3-50).

Figure 3-50 IP & MAC Binding Setting

¾MAC Address - The MAC address of the controlled computer in the LAN.

¾IP Address - The assigned IP address of the controlled computer in the LAN.

¾Bind - Whether or not enable the arp binding.

¾Modify - Edit or delete item.

When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Modify button, and then you will go to the next page. This page is used for adding or modifying an IP & MAC Binding entry (shown in Figure 3-51).

58

Image 65
Contents Rev 1.0.4 TL-WR340G TL-WR340GD 54Mbps Wireless RouterAll rights reserved COPYRIGHT & TRADEMARKSCE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement 2400.0-2483.5 MHz National RestrictionsCountry RestrictionProduct Description 54Mbps Wireless Router DECLARATION OF CONFORMITYModel No. TL-WR340G/TL-WR340GD ETSI EN 300Package Contents CONTENTSHardware Installation Chapter 3. Quick Installation GuideAppendix B Configuring the PC Appendix A FAQAppendix C Specifications Appendix C GlossaryConventions Package ContentsChapter 1.Introduction 1.2 Main Features1.1 Product Overview 54Mbps Wireless Router User Guide¾ Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/2/1Mbps data transfer rates 2.1 The Front Panel Chapter 2.Hardware InstallationLED Explanation Indication2.3 System Requirements 2.2 The Back Panel2.5 Connecting the Device 2.4 Installation Environment Requirements2.6 Configure PC TL-WR340G/TL-WR340GD ¾ Configure the IP address manually Please check it following these steps 3.1 TCP/IP Configuration Chapter 3.Quick Installation GuidePlease check the connection following these steps Figure 3-1 Success result of Ping command3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-8 Quick Setup - Static IP 6. Click the Next button. You will then see the Finish page 4.2 Status Chapter 4.Software Configuration4.1 Login Please refer to Quick Installation Guide 4.3 Quick Setup4.4.2 WAN 4.4 Network4.4.1 LAN Figure 3-4 WAN - Dynamic IP Figure 3-5 WAN - Static IP Figure 3-6 WAN - PPPoE 3-7 will then appear Figure 3-7 PPPoE Advanced Settings Figure 3-8 802.1X + Dynamic IP Settings TL-WR340G/TL-WR340GD QLD - qld.bigpond.net.au NSW / ACT - nsw.bigpond.net.auTL-WR340G/TL-WR340GD 54Mbps Wireless Router User GuideTL-WR340G/TL-WR340GD ¾ Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise TL-WR340G/TL-WR340GD 54Mbps Wireless Router User GuideTL-WR340G/TL-WR340GD 54Mbps Wireless Router User GuideTL-WR340G/TL-WR340GD 4.4.3 MAC Clone 4.5 Wireless4.5.1 Wireless Settings TL-WR340G/TL-WR340GD WEP - Select WEP authentication type based on 802.11 authentications Figure 3-19 WPA-PSK/WPA2-PSK 4.5.2 MAC Filtering 5. Click the Save button to save this entry 4.5.3 Wireless Statistics 4.6 DHCP 4.6.1 DHCP Settings4.6.3 Address Reservation 4.6.2 DHCP Clients ListTo Reserve IP addresses The function wont take effect until the router rebootsTo setup a virtual server entry 4.7 Forwarding4.7.1 Virtual Servers 4.7.2 Port Triggering TL-WR340G/TL-WR340GD 4.7.3 DMZ 4.7.4 UPnP 4.8.1 Firewall 4.8 Security4.8.2 IP Address Filtering 4.8.3 Domain Filtering TL-WR340G/TL-WR340GD 4.8.4 MAC Address Filtering 4.8.5 Remote Management 4.8.6 Advanced Security 4.9 Static Routing To add static routing entries TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 4.10 IP & MAC Binding Setting4.10.1 Binding Setting To add IP & MAC Binding entries 4.10.2 ARP ListTo modify or delete an existing entry To find an existing entry4.11.1 Dyndns.org DDNS 4.11 Dynamic DNS4.11.2 Oray.net DDNS 4.11.3 Comexe.cn DDNS 4.12.1 Time 4.12 System Tools1. Select using daylight saving time 4.12.2 Diagnostic4.12.3 Firmware 4.12.4 Factory Defaults 4.12.6 Reboot 4.12.5 Backup & Restore4.12.8 Syslog 4.12.7 PasswordStatistics Table 4.12.9 StatisticsIP Address Total1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? MAC CloneRemote Management 4. I want to build a WEB Server on the LAN, what should I do?Virtual Server 1. Configure TCP/IP component Appendix B Configuring the PCshown in the Figure below Now you have two ways to configure the TCP/IP protocol below¾ Setting IP address automatically 1 Select Use the following IP address radio button. And the following items available ¾ Setting IP address manuallyClick OK to keep your settings Physical and Environment SpecificationsAppendix C Appendix C Glossary
Related manuals
Manual 2 pages 7.63 Kb