TP-Link TL-WR340G/TL-WR340GD, 54Mbps Wireless Router User Guide, shown in the Figure below

Page 82

Now you have two ways to configure the TCP/IP protocol below:

TL-WR340G/TL-WR340GD

54Mbps Wireless Router User Guide

Figure 0-2

5)The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.

Now you have two ways to configure the TCP/IP protocol below:

¾Setting IP address automatically

Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as

shown in the Figure below:

75

Image 82

Contents TL-WR340G TL-WR340GD 54Mbps Wireless Router Rev 1.0.4COPYRIGHT & TRADEMARKS All rights reservedFCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Country National Restrictions2400.0-2483.5 MHz RestrictionModel No. TL-WR340G/TL-WR340GD DECLARATION OF CONFORMITYProduct Description 54Mbps Wireless Router ETSI EN 300Hardware Installation CONTENTSPackage Contents Chapter 3. Quick Installation GuideAppendix C Specifications Appendix A FAQAppendix B Configuring the PC Appendix C GlossaryPackage Contents Conventions1.1 Product Overview 1.2 Main FeaturesChapter 1.Introduction 54Mbps Wireless Router User Guide¾ Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/2/1Mbps data transfer rates LED Explanation Chapter 2.Hardware Installation2.1 The Front Panel Indication2.2 The Back Panel 2.3 System Requirements2.4 Installation Environment Requirements 2.5 Connecting the Device2.6 Configure PC 54Mbps Wireless Router User Guide ¾ Configure the IP address manually Please check it following these steps Chapter 3.Quick Installation Guide 3.1 TCP/IP ConfigurationFigure 3-1 Success result of Ping command Please check the connection following these steps3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-8 Quick Setup - Static IP 6. Click the Next button. You will then see the Finish page 4.1 Login Chapter 4.Software Configuration4.2 Status 4.3 Quick Setup Please refer to Quick Installation Guide4.4.1 LAN 4.4 Network4.4.2 WAN Figure 3-4 WAN - Dynamic IP Figure 3-5 WAN - Static IP Figure 3-6 WAN - PPPoE 3-7 will then appear Figure 3-7 PPPoE Advanced Settings Figure 3-8 802.1X + Dynamic IP Settings 54Mbps Wireless Router User Guide NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au54Mbps Wireless Router User Guide TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide ¾ Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise 54Mbps Wireless Router User Guide TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide 4.5 Wireless 4.4.3 MAC Clone4.5.1 Wireless Settings 54Mbps Wireless Router User Guide WEP - Select WEP authentication type based on 802.11 authentications Figure 3-19 WPA-PSK/WPA2-PSK 4.5.2 MAC Filtering 5. Click the Save button to save this entry 4.5.3 Wireless Statistics 4.6.1 DHCP Settings 4.6 DHCP4.6.2 DHCP Clients List 4.6.3 Address ReservationThe function wont take effect until the router reboots To Reserve IP addresses4.7.1 Virtual Servers 4.7 ForwardingTo setup a virtual server entry 4.7.2 Port Triggering 54Mbps Wireless Router User Guide 4.7.3 DMZ 4.7.4 UPnP 4.8 Security 4.8.1 Firewall4.8.2 IP Address Filtering 4.8.3 Domain Filtering 54Mbps Wireless Router User Guide 4.8.4 MAC Address Filtering 4.8.5 Remote Management 4.8.6 Advanced Security 4.9 Static Routing To add static routing entries 4.10.1 Binding Setting 4.10 IP & MAC Binding SettingTL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide To modify or delete an existing entry 4.10.2 ARP ListTo add IP & MAC Binding entries To find an existing entry4.11 Dynamic DNS 4.11.1 Dyndns.org DDNS4.11.2 Oray.net DDNS 4.11.3 Comexe.cn DDNS 4.12 System Tools 4.12.1 Time4.12.2 Diagnostic 1. Select using daylight saving time4.12.3 Firmware 4.12.4 Factory Defaults 4.12.5 Backup & Restore 4.12.6 Reboot4.12.7 Password 4.12.8 SyslogIP Address 4.12.9 StatisticsStatistics Table TotalAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?MAC Clone 3. I want to use Netmeeting, what do I need to do?4. I want to build a WEB Server on the LAN, what should I do? Remote ManagementVirtual Server Appendix B Configuring the PC 1. Configure TCP/IP component¾ Setting IP address automatically Now you have two ways to configure the TCP/IP protocol belowshown in the Figure below ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the following items availableClick OK to keep your settings Appendix C SpecificationsPhysical and Environment Appendix C Glossary

Related manuals

Manual 2 pages 7.63 Kb