TP-Link manual TL-WR340G/TL-WR340GD, 54Mbps Wireless Router User Guide

Page 84
Click OK to keep your settings.

TL-WR340G/TL-WR340GD

54Mbps Wireless Router User Guide

Now:

Click OK to keep your settings.

77

Page 83 Page 85
Image 84
Page 83 Page 85
Contents TL-WR340G TL-WR340GD 54Mbps Wireless Router Rev 1.0.4COPYRIGHT & TRADEMARKS All rights reservedFCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning National Restrictions 2400.0-2483.5 MHzCountry RestrictionDECLARATION OF CONFORMITY Product Description 54Mbps Wireless RouterModel No. TL-WR340G/TL-WR340GD ETSI EN 300CONTENTS Package ContentsHardware Installation Chapter 3. Quick Installation GuideAppendix A FAQ Appendix B Configuring the PCAppendix C Specifications Appendix C GlossaryPackage Contents Conventions1.2 Main Features Chapter 1.Introduction1.1 Product Overview 54Mbps Wireless Router User Guide¾ Supports 54/48/36/24/18/12/9/6Mbps or 11/5.5/2/1Mbps data transfer rates Chapter 2.Hardware Installation 2.1 The Front PanelLED Explanation Indication2.2 The Back Panel 2.3 System Requirements2.4 Installation Environment Requirements 2.5 Connecting the Device2.6 Configure PC 54Mbps Wireless Router User Guide ¾ Configure the IP address manually Please check it following these steps Chapter 3.Quick Installation Guide 3.1 TCP/IP ConfigurationFigure 3-1 Success result of Ping command Please check the connection following these steps3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-8 Quick Setup - Static IP 6. Click the Next button. You will then see the Finish page Chapter 4.Software Configuration 4.1 Login4.2 Status 4.3 Quick Setup Please refer to Quick Installation Guide4.4 Network 4.4.1 LAN4.4.2 WAN Figure 3-4 WAN - Dynamic IP Figure 3-5 WAN - Static IP Figure 3-6 WAN - PPPoE 3-7 will then appear Figure 3-7 PPPoE Advanced Settings Figure 3-8 802.1X + Dynamic IP Settings 54Mbps Wireless Router User Guide NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au54Mbps Wireless Router User Guide TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide ¾ Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise 54Mbps Wireless Router User Guide TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide TL-WR340G/TL-WR340GD54Mbps Wireless Router User Guide 4.5 Wireless 4.4.3 MAC Clone4.5.1 Wireless Settings 54Mbps Wireless Router User Guide WEP - Select WEP authentication type based on 802.11 authentications Figure 3-19 WPA-PSK/WPA2-PSK 4.5.2 MAC Filtering 5. Click the Save button to save this entry 4.5.3 Wireless Statistics 4.6.1 DHCP Settings 4.6 DHCP4.6.2 DHCP Clients List 4.6.3 Address ReservationThe function wont take effect until the router reboots To Reserve IP addresses4.7 Forwarding 4.7.1 Virtual ServersTo setup a virtual server entry 4.7.2 Port Triggering 54Mbps Wireless Router User Guide 4.7.3 DMZ 4.7.4 UPnP 4.8 Security 4.8.1 Firewall4.8.2 IP Address Filtering 4.8.3 Domain Filtering 54Mbps Wireless Router User Guide 4.8.4 MAC Address Filtering 4.8.5 Remote Management 4.8.6 Advanced Security 4.9 Static Routing To add static routing entries 4.10 IP & MAC Binding Setting 4.10.1 Binding SettingTL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 4.10.2 ARP List To add IP & MAC Binding entriesTo modify or delete an existing entry To find an existing entry4.11 Dynamic DNS 4.11.1 Dyndns.org DDNS4.11.2 Oray.net DDNS 4.11.3 Comexe.cn DDNS 4.12 System Tools 4.12.1 Time4.12.2 Diagnostic 1. Select using daylight saving time4.12.3 Firmware 4.12.4 Factory Defaults 4.12.5 Backup & Restore 4.12.6 Reboot4.12.7 Password 4.12.8 Syslog4.12.9 Statistics Statistics TableIP Address TotalAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?MAC Clone 3. I want to use Netmeeting, what do I need to do?4. I want to build a WEB Server on the LAN, what should I do? Remote ManagementVirtual Server Appendix B Configuring the PC 1. Configure TCP/IP componentNow you have two ways to configure the TCP/IP protocol below ¾ Setting IP address automaticallyshown in the Figure below ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the following items availableClick OK to keep your settings Specifications Appendix CPhysical and Environment Appendix C Glossary
Related manuals
Manual 2 pages 7.63 Kb
Top Page Image Contents