TP-Link TL-WA901ND manual Rear Panel,  Used as Reset button

Page 12

TL-WA901ND300Mbps Wireless N Access Point User Guide

1.4.2 The Rear Panel

Figure 1-2

Viewed from left to right, the following parts are located on the rear panel of TL-WA901ND. ON/OFF: The switch for the power.

POWER: The power port connects to the power adapter provided with the TL-WA901ND 300Mbps Wireless N Access Point.

Ethernet: One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or a router.

WPS/RESET: This button is used for both WPS and Reset function. To use the WPS function, press it for less than five seconds; to use the RESET function, press it for more than five seconds.

Used as RESET button:

There are two ways to reset to the Router's factory defaults:

1)Use the Factory Defaults function on System Tools ->Factory Defaults page in the Router's Web-based Utility.

2)Use the WPS/RESET button: With the Router powered on, press and hold the WPS/RESET button (more than 5 seconds) until the SYS LED becomes quick-flash from slow-flash. Then release the button and wait the Access Point to reboot to its factory default settings.

4

Image 12

Contents TL-WA901ND Copyright & Trademarks FCC Statement Korea Warning Statements Safety Information Product Description 300Mbps Wireless N Access Point Yang Hongliang Product Manager of International BusinessContents Factory Defaults Backup & Restore Reboot Password System Log Package Contents Introduction Product OverviewConventions Main Features AppearanceFront Panel LED Explanation Name Status Indication Used as Reset button Rear PanelTL-WA901ND  Used as WPS buttonHardware Installation Connecting the DeviceBefore You Begin Basic Requirements Note TL-WA901ND300Mbps Wireless N Access Point User Guide Quick Installation Guide Quick SetupQuick Setup TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide 12 Network Setting 13 Quick Setup Finish Configure the Device LoginStatus WPS Device Status ClientTo add a new device By PBCMethod One Method Two Method Three Add a New DeviceII. By PIN Enter the PIN Click ConnectNetwork Wireless Wireless Settings Wireless menu Note TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Access Point TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Switch Egress Rule Processing mode of Utag FramesPort  Note 13 Wireless Settings in Repeater mode 14 Wireless Settings in Repeater mode TL-WA901ND300Mbps Wireless N Access Point User Guide 15 Wireless Settings in Bridge with AP mode Wireless Security Access Point TL-WA901ND Multi-SSID Client TL-WA901ND300Mbps Wireless N Access Point User Guide WDS Repeater 20 Wireless Security Repeater Universal RepeaterTL-WA901ND300Mbps Wireless N Access Point User Guide Bridge with AP TL-WA901ND Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entryWireless Advanced Wireless Statistics Throughput MonitorDhcp 27 The Dhcp menuDhcp Settings Dhcp Clients List Address ReservationSystem Tools To Reserve IP addressesTo modify a Reserved IP address To delete all Reserved IP addresses Click Clear AllSnmp 31 The System Tools menuDiagnostic TL-WA901ND300Mbps Wireless N Access Point User Guide 34 Diagnostic Results Ping Watch DogFirmware Upgrade To upgrade the devices firmware, follow these instructionsFactory Defaults Backup & RestoreReboot PasswordSystem Log Appendix a Application Example TL-WA901ND TL-WA901ND300Mbps Wireless N Access Point User Guide Appendix B Factory Defaults Default ValueCommon Default Settings WirelessAppendix C Troubleshooting T2. What can I do if I forget my password?Appendix D Specifications GeneralPhysical and Environment Appendix E Glossary TL-WA901ND300Mbps Wireless N Access Point User Guide