TP-Link TL-WA901ND manual Diagnostic

Page 66

TL-WA901ND300Mbps Wireless N Access Point User Guide

SNMP Agent - Select the radio button before Enable will enable this function if you want to have remote control through SNMPv1/v2 agent with MIB-II. Select the radio button before Disable will disable this function. The default setting is Disable.

SysContact - The textual identification of the contact person for this managed node.

SysName - An administratively-assigned name for this managed node.

SysLocation - The physical location of this node.

Note:

Specifying one of these values via the Device's Web-Based Utility makes the corresponding object read-only. If there isn't such a config setting, then the write request will succeed (assuming suitable access control settings), but the new value would be forgotten the next time the agent was restarted.

Get Community - Enter the community name that allows Read-Only access to the Device's SNMP information. The community name can be considered a group password. The default setting is “public”.

Get Source - Get source defines the IP address or subnet for management systems that can read information from this 'get' community device.

Set Community - Enter the community name that allows Read/Write access to the Device's SNMP information. The community name can be considered a group password. The default setting is “private”.

Set Source - Set source defines the IP address or subnet for management systems that can control this 'set' community device.

Note:

A restricted source can be a specific IP address (e.g. 10.10.10.1), or a subnet - represented as IP/BITS (e.g. 10.10.10.0/24). If an IP Address of 0.0.0.0 is specified, the agent will accept all requests under the corresponding community name.

Click the Save button to save your settings.

4.8.2 Diagnostic

Selecting System Tools > Diagnostic allow you to check the connections of your network components on the screen shown in Figure 4-33.

58

Image 66
Contents TL-WA901ND Copyright & Trademarks FCC Statement Korea Warning Statements Safety Information Product Description 300Mbps Wireless N Access Point Yang Hongliang Product Manager of International BusinessContents Factory Defaults Backup & Restore Reboot Password System Log Package Contents Introduction Product OverviewConventions Front Panel Main FeaturesAppearance LED Explanation Name Status Indication Used as Reset button Rear PanelTL-WA901ND  Used as WPS buttonBefore You Begin Hardware InstallationConnecting the Device Basic Requirements Note TL-WA901ND300Mbps Wireless N Access Point User Guide Quick Installation Guide Quick SetupQuick Setup TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide 12 Network Setting 13 Quick Setup Finish Configure the Device LoginStatus WPS Device Status ClientTo add a new device By PBCMethod One Method Two Method Three Add a New DeviceII. By PIN Enter the PIN Click ConnectNetwork Wireless Wireless Settings Wireless menu Note TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Access Point TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Switch Egress Rule Processing mode of Utag FramesPort  Note 13 Wireless Settings in Repeater mode 14 Wireless Settings in Repeater mode TL-WA901ND300Mbps Wireless N Access Point User Guide 15 Wireless Settings in Bridge with AP mode Wireless Security Access Point TL-WA901ND Multi-SSID Client TL-WA901ND300Mbps Wireless N Access Point User Guide WDS Repeater 20 Wireless Security Repeater Universal RepeaterTL-WA901ND300Mbps Wireless N Access Point User Guide Bridge with AP TL-WA901ND Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entryWireless Advanced Wireless Statistics Throughput MonitorDhcp 27 The Dhcp menuDhcp Settings Dhcp Clients List Address ReservationTo modify a Reserved IP address System ToolsTo Reserve IP addresses To delete all Reserved IP addresses Click Clear AllSnmp 31 The System Tools menuDiagnostic TL-WA901ND300Mbps Wireless N Access Point User Guide 34 Diagnostic Results Ping Watch DogFirmware Upgrade To upgrade the devices firmware, follow these instructionsFactory Defaults Backup & RestoreReboot PasswordSystem Log Appendix a Application Example TL-WA901ND TL-WA901ND300Mbps Wireless N Access Point User Guide Common Default Settings Appendix B Factory DefaultsDefault Value WirelessAppendix C Troubleshooting T2. What can I do if I forget my password?Appendix D Specifications GeneralPhysical and Environment Appendix E Glossary TL-WA901ND300Mbps Wireless N Access Point User Guide