TP-Link TL-WA901ND manual To set up an entry, follow these instructions

Page 58

TL-WA901ND300Mbps Wireless N Access Point User Guide

Status - Select a status for this entry, either Enabled or Disabled.

To set up an entry, follow these instructions:

First, you must decide whether the unspecified wireless stations can access the device or not. If you desire that the unspecified wireless stations can access the device, please select the radio button Deny the stations specified by any enabled entries in the list to access, otherwise, select the radio button Allow the stations specified by any enabled entries in the list to

access.

To add a MAC Address Filtering entry, follow these instructions:

1.Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B.

2.Enter a simple description of the wireless station in the Description field. For example: Wireless station A.

3.Select Enabled or Disabled for this entry on the Status pull-down list.

4.Click the Save button to save this entry.

To add additional entries, repeat steps 1-4.

To modify or delete an existing entry:

1.Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete.

2.Modify the information.

3.Click the Save button.

Click the Enable All button to make all entries enabled

Click the Disabled All button to make all entries disabled.

Click the Delete All button to delete all entries

Click the Next button to go to the next page and click the Previous button to return to the previous page.

For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE is able to access the device, while all other wireless stations cannot access the device, you should configure the Wireless MAC Address Filtering list by following these steps:

1.Click the Enable button to enable this function.

2.Select the radio button: Allow the stations specified by any enabled entries in the list to access for Filtering Rules.

3.Delete all or disable all entries if there are any entries already.

4.Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC Address field, enter Wireless Station A in the Description field and select Enabled in the Status pull-down list. Click the Save button.

The filtering rules that configured should be similar to the following list:

50

Page 57 Page 59
Image 58
Page 57 Page 59
Contents TL-WA901ND Copyright & Trademarks FCC Statement Korea Warning Statements Safety Information Product Description 300Mbps Wireless N Access Point Yang Hongliang Product Manager of International BusinessContents Factory Defaults Backup & Restore Reboot Password System Log Package Contents Product Overview IntroductionConventions Front Panel Main FeaturesAppearance LED Explanation Name Status Indication Used as Reset button Rear PanelTL-WA901ND  Used as WPS buttonBefore You Begin Hardware InstallationConnecting the Device Basic Requirements Note TL-WA901ND300Mbps Wireless N Access Point User Guide Quick Installation Guide Quick SetupQuick Setup TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide 12 Network Setting 13 Quick Setup Finish Configure the Device LoginStatus WPS Device Status ClientBy PBC To add a new deviceMethod One Method Two Method Three Add a New DeviceII. By PIN Enter the PIN Click ConnectNetwork Wireless Wireless Settings Wireless menu Note TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Access Point TL-WA901ND300Mbps Wireless N Access Point User Guide Egress Rule Processing mode of Utag Frames Configure the SwitchPort  Note 13 Wireless Settings in Repeater mode 14 Wireless Settings in Repeater mode TL-WA901ND300Mbps Wireless N Access Point User Guide 15 Wireless Settings in Bridge with AP mode Wireless Security Access Point TL-WA901ND Multi-SSID Client TL-WA901ND300Mbps Wireless N Access Point User Guide WDS Repeater 20 Wireless Security Repeater Universal RepeaterTL-WA901ND300Mbps Wireless N Access Point User Guide Bridge with AP TL-WA901ND Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entryWireless Advanced Wireless Statistics Throughput MonitorDhcp 27 The Dhcp menuDhcp Settings Dhcp Clients List Address ReservationTo modify a Reserved IP address System ToolsTo Reserve IP addresses To delete all Reserved IP addresses Click Clear AllSnmp 31 The System Tools menuDiagnostic TL-WA901ND300Mbps Wireless N Access Point User Guide 34 Diagnostic Results Ping Watch DogFirmware Upgrade To upgrade the devices firmware, follow these instructionsFactory Defaults Backup & RestoreReboot PasswordSystem Log Appendix a Application Example TL-WA901ND TL-WA901ND300Mbps Wireless N Access Point User Guide Common Default Settings Appendix B Factory DefaultsDefault Value WirelessAppendix C Troubleshooting T2. What can I do if I forget my password?General Appendix D SpecificationsPhysical and Environment Appendix E Glossary TL-WA901ND300Mbps Wireless N Access Point User Guide
Top Page Image Contents