TP-Link TL-WA901ND manual  Note

Page 15

TL-WA901ND300Mbps Wireless N Access Point User Guide

Figure 2-1 The Example of Infrastructure Network Incorporating the TL-WA901ND To establish a typical connection of the AP, please take the following steps:

1.Connect the Cable or DSL modem to a Router.

2.Locate an optimum location for the AP. The best place is usually near the center of the area in which your wireless devices like PCs, smart phones will wirelessly connect.

3.Adjust the direction of the antenna. Normally, upright is a good direction.

4.Connect the Ethernet Broadband Router to the TL-WA901ND Access Point. Power on the AP.

5.Then you can connect a desktop PC or laptop to your network. (Make sure your computer or laptop is equipped with a Wireless Adapter and the IP address is configured as obtain an IP address automatically.)

Note:

If you are not so clear about how to connect your devices to the network, please refer to Appendix A Application Example.

7

Image 15

Contents TL-WA901ND Copyright & Trademarks FCC Statement Korea Warning Statements Safety Information Yang Hongliang Product Manager of International Business Product Description 300Mbps Wireless N Access PointContents Factory Defaults Backup & Restore Reboot Password System Log Package Contents Introduction Product OverviewConventions LED Explanation Name Status Indication Main FeaturesAppearance Front PanelRear Panel  Used as Reset button Used as WPS button TL-WA901NDBasic Requirements Hardware InstallationConnecting the Device Before You Begin Note TL-WA901ND300Mbps Wireless N Access Point User Guide Quick Setup Quick Installation GuideQuick Setup TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide TL-WA901ND300Mbps Wireless N Access Point User Guide 12 Network Setting 13 Quick Setup Finish Login Configure the DeviceStatus Device Status Client WPSTo add a new device By PBCMethod One Method Two Add a New Device Method ThreeII. By PIN Click Connect Enter the PINNetwork Wireless Wireless menu Wireless Settings Note TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Access Point TL-WA901ND300Mbps Wireless N Access Point User Guide Configure the Switch Egress Rule Processing mode of Utag FramesPort  Note 13 Wireless Settings in Repeater mode 14 Wireless Settings in Repeater mode TL-WA901ND300Mbps Wireless N Access Point User Guide 15 Wireless Settings in Bridge with AP mode Wireless Security Access Point TL-WA901ND Multi-SSID Client TL-WA901ND300Mbps Wireless N Access Point User Guide WDS Repeater Universal Repeater 20 Wireless Security RepeaterTL-WA901ND300Mbps Wireless N Access Point User Guide Bridge with AP TL-WA901ND Wireless MAC Filtering To modify or delete an existing entry To set up an entry, follow these instructionsWireless Advanced Throughput Monitor Wireless Statistics27 The Dhcp menu DhcpDhcp Settings Address Reservation Dhcp Clients ListTo delete all Reserved IP addresses Click Clear All System ToolsTo Reserve IP addresses To modify a Reserved IP address31 The System Tools menu SnmpDiagnostic TL-WA901ND300Mbps Wireless N Access Point User Guide Ping Watch Dog 34 Diagnostic ResultsTo upgrade the devices firmware, follow these instructions Firmware UpgradeBackup & Restore Factory DefaultsPassword RebootSystem Log Appendix a Application Example TL-WA901ND TL-WA901ND300Mbps Wireless N Access Point User Guide Wireless Appendix B Factory DefaultsDefault Value Common Default SettingsT2. What can I do if I forget my password? Appendix C TroubleshootingAppendix D Specifications GeneralPhysical and Environment Appendix E Glossary TL-WA901ND300Mbps Wireless N Access Point User Guide